Indian Navy - Andhra Pradesh

33380445 tender for 24k hourly routines on 02 das in ship 1 24k.dismantle auxiliary drives and check bearing clearances. renew bearings if necessary. examine all gear teeth for pitting and scuffing. vta 28 dm.vta 28 dm 2 24k.renew big end bearings, their bolts, nuts and washers.vta 28 dm.vta 28 dm 3 24k.check main bearing clearances and examine the condition. renew bearing if clearances are excessive.vta 28 dm.vta 28 dm 4 24k.remove, clean and examine all cylinder liners for scoring and corrosion. gauge liners internally. renew if necessary.vta 28 dm.vta 28 dm 5 24k.clean all water passages. renew all sealing rings.vta 28 dm.vta 28 dm 6 24k.examine and gauge all pistons. renew pistons if necessary. vta 28 dm.vta 28 dm 7 24k.renew all piston rings.vta 28 dm.vta 28 dm 8 24k.remove crankshaft and check for cracks, scoring and deflection, ( eccentricity ) . clean and flush out oil ways. renew teflon seals.vta 28 dm.vta 28 dm 9 24k.overhaul governor. renew worn out parts. calibrate governor after completion of overhauling.vta 28 dm.vta 28 dm 10 24k. ( a ) remove and chemically clean lub oil cooler and fresh water cooler and carry out pressure testing. replace if required. ( b ) renew gasket and `o seals.vta 28 dm.vta 28 dm 11 24k.remove and check the over speed trip ( protection device / sensor ) for correct setting / functioning, calibrate if necessary.vta 28 dm.vta 28 dm 12 24k.refit cam shaft drive assembly.vta 28 dm.vta 28 dm 13 24k.check all camshaft bearing clearances. renew if necessary. check valve timing.vta 28 dm.vta 28 dm 14 24k.check all connecting rods for bend and twist. clean and flush out oil passages.vta 28 dm.vta 28 dm 15 24k.renew hp fuel pump.vta 28 dm.vta 28 dm 16 24k.remove, clean and retreat the crankcase. vta 28 dm.vta 28 dm 17 24k.clean and repaint bedplate.vta 28 dm.vta 28 dm 18 24k.renew all flexible hoses.vta 28 dm.vta 28 dm 19 24k.gauge all gudgeon pins. replace if wear is excessive.vta 28 dm.vta 28 dm 20 24k.renew s.v. mountings.vta 28 dm.vta 28 dm 21 24k.overhaul turbo supercharger. renew entire unit if parts are excessively worn out.vta 28 dm.vta 28 dm 22 24k.remove air cooler, chemically clean and pressure test on completion of cleaning. replace if required.vta 28 dm.vta 28 dm 23 24k.overhaul air starting motor. renew worn partsvta 28 dm.vta 28 dm 24 24k.renew silicon vibration damper where fitted.vta 28 dm.vta 28 dm 25 24k.overhaul / renew holset / vulcan / centamax coupling as necessary. renew the rubber inserts / member of the flexible coupling. renew all fasteners / bolts while assembling the coupling as per oem recommended procedure. carry out engine to alternator alignment procedure while maintaining the crankshaft end clearances. dowel the alternator carry out full load trials and vibration checks before normal services.vta 28 dm 26 mandatory.spares.camshaft.part no 4073133 27 mandatory.spares.camshaft.part no 4073134 28 mandatory.spares.bearing, thrust.part no 9235 1 29 mandatory.spares.bushing.part no 70437 30 mandatory.spares.pickup, magnetic.part no 4105447 31 mandatory.spares.liner, cylinder.part no 3241328 32 mandatory.spares.damper, vibration.part no 3077985 33 mandatory.spares.kit piston ring set v 28.part no kit3238194 34 mandatory.spares.set main bear..std..part no kitar 4220 35 mandatory.spares.bushing.part no 187420 36 mandatory.spares.bearing, connecting rod.part no 200600 37 mandatory.spares.bolt, connecting rod.part no 146856 38 mandatory.spares.nut, heavy hexagon.part no 69936 39 mandatory.spares.washer, plain.part no 3025100 40 mandatory.spares.nozzle, piston cooling.part no 3044241 41 mandatory.spares.collet, valve.part no 127554 42 mandatory.spares.valve, exhaust.part no 3086436 43 mandatory.spares.guide, valve spring.part no 170296 44 mandatory.spares.guide, valve spring.part no 172034 45 mandatory.spares.spring, valve.part no 211999 46 mandatory.spares.valve, intake.part no 3803876 47 mandatory.spares.insert, valve.part no 127930 48 mandatory.spares.guide, valve stem.part no 3006456 49 mandatory.spares.insert, valve.part no 3084185 50 mandatory.spares.guide, valve crosshead.part no 123558 51 mandatory.spares.retainer, valve spring.part no 219091 52 mandatory.spares.sleeve, injector.part no 3406702 53 mandatory.spares.seal, o ring.part no 3007759 54 mandatory.spares.guide, valve crosshead.part no 123558 55 mandatory.spares.retainer, valve spring.part no 219091 56 mandatory.spares.spring, compression.part no 219092 57 mandatory.spares.plug, o ring.part no 162143 58 mandatory.spares.crosshead.part no 3030038 59 mandatory.spares.screw, slotted set.part no 168306 60 mandatory.spares.nut, regular hexagon.part no s 212 61 mandatory.spares.screw, hexagon head cap.part no 108601 62 mandatory.spares.screw, captive washer cap.part no 3042889 63 mandatory.spares.shaft, rocker lever.part no bm71481 64 mandatory.spares.bushing.part no 140330 65 mandatory.spares.bushing.part no 218153 66 mandatory.spares.plug, expansion.part no 175830 67 mandatory.spares.lever, rocker.part no bm95161 68 mandatory.spares.lever, rocker.part no bm95162 69 mandatory.spares.lever, rocker.part no ar 2308 70 mandatory.spares.tappet, injector.part no 4071619 71 mandatory.spares.tappet, valve.part no 4071615 72 mandatory.spares.rod, push.part no 3046419 73 mandatory.spares.rod, push.part no 3046432 74 mandatory.spares.thermostat.part no 135675 75 mandatory.spares.seal, thermostat.part no 186780 76 mandatory.spares.hose, plain.part no 3017278 77 mandatory.spares.clamp, hose.part no 43828 d 78 mandatory.spares.gasket, thermostat housing.part no 102867 79 mandatory.spares.gasket, water manifold.part no 102791 80 mandatory.spares.gasket, cover plate.part no 124246 81 mandatory.spares.screw, hexagon head cap.part no 120516 82 mandatory.spares.gasket, wtr trf connection.part no 64413 83 mandatory.spares.kit inj barrel plunger.part no kit3238193 84 mandatory.spares.seal, o ring.part no 193736 85 mandatory.spares.spring, compression.part no 166009 86 mandatory.spares.ball, check.part no 167157 87 mandatory.spares.gasket, injector.part no 173086 88 mandatory.spares.retainer, screen.part no 174299 89 mandatory.spares.pin, roll.part no 203426 90 mandatory.spares.screen, filter.part no 3054999 91 mandatory.spares.link, injector plunger.part no 191916 92 mandatory.spares.plug, injector orifice.part no 3045047 93 mandatory.spares.link, injector plunger.part no 191916 94 mandatory.spares.plug, threaded.part no 173085 95 mandatory.spares.clamp, injector.part no 3031137 96 mandatory.spares.kit, turbo repair 4lg.part no 3545661 97 mandatory.spares.stud, double end plain.part no 3042353 98 mandatory.spares.nut, regular hexagon.part no 219138 99 mandatory.spares.gasket, turbocharger.part no 3519763 100 mandatory.spares.gasket, turbocharger.part no 3709749 101 mandatory.spares.gasket, turbocharger.part no 3519762 102 mandatory.spares.gasket set.part no kit3240239 103 mandatory.spares.gasket set vta 1710.part no kit3247965 104 mandatory.spares.gasket, exhaust manifold.part no 3081076 105 mandatory.spares.core, cooler.part no 3010612 106 mandatory.spares.seal, o ring.part no 3010617 107 mandatory.spares.gasket, lub oil clr hsg.part no 172723 108 mandatory.spares.pump, lubricating oil.part no 4979720 109 mandatory.spares.inhibitor, corrosion 10 liters.part no 3167218 110 mandatory.spares.radiwash 3 liters.part no ax1013359 111 mandatory.spares.pump, water.part no 4911528 112 mandatory.spares.gasket, water pump.part no 123078 113 mandatory.spares.gasket, water pump.part no 3011230 114 mandatory.spares.gasket, water pump.part no 69654 115 mandatory.spares.gasket, connection.part no 113914 116 mandatory.spares.gasket, heat exchanger.part no 4104940 117 mandatory.spares.gasket, sea water pump.part no 3055769 118 mandatory.spares.hose, plain.part no 4104834 119 mandatory.spares.clamp, t bolt.part no 140315 120 mandatory.spares.tube, water makeup.part no 4105019 121 mandatory.spares.hose, plain.part no 102522 122 mandatory.spares.clamp, hose.part no 43828 c 123 mandatory.spares.hose, flexible.part no ak 5040 ss 124 mandatory.spares.tank, expansion.part no 4104977 125 mandatory.spares.core, aftercooler.part no 3026923 126 mandatory.spares.gasket, wtr trf connection.part no 215044 127 mandatory.spares.hose, plain.part no 3027706 128 mandatory.spares.gasket, aft housing.part no 3077201 129 mandatory.spares.hose, plain.part no 4957919 130 mandatory.spares.clamp, hose.part no 3010550 131 mandatory.spares.clamp, hose.part no 3026806 132 mandatory.spares.seal, o ring.part no 195952 133 mandatory.spares.element, lub oil filter.part no 3238204 134 mandatory.spares.kit, fuel filter and ring.part no 3238493 135 mandatory.spares.kit, super byp.filter elem.part no 3879488 136 mandatory.spares.seal, o ring.part no 3010937 137 mandatory.spares.element, air cleaner.part no 4020552 138 mandatory.spares.element, air cleaner.part no 4020551 139 mandatory.spares.indicator, restriction.part no 3872813 140 mandatory.spares.separator, fuel water.part no 4912776 141 mandatory.spares.breather, crankcase.part no 255180 142 mandatory.spares.primer, engine lubricating.part no 3225432 143 mandatory.spares.valve, fuel flow.part no 3233695 144 mandatory.spares.hose, flexible.part no am16048 ss 145 mandatory.spares.hose, flexible.part no am10040 ss 146 mandatory.spares.hose, flexible.part no ak10030 ss 147 mandatory.spares.gasket governor set.part no kitbm68356 148 mandatory.spares.valve, shutoff.part no 3096859 149 mandatory.spares.screen, filter.part no 146483 150 mandatory.spares.shaft, fuel pump drive.part no 212601 151 mandatory.spares.screen, filter.part no 3090769 152 mandatory.spares.bushing, tachometer drive.part no 212609 153 mandatory.spares.seal, rectangular ring.part no 154087 154 mandatory.spares.bearing, ball.part no s 16052 155 mandatory.spares.damper, fuel pump.part no bm76340 156 mandatory.spares.valve, shutoff.part no 3096859 157 mandatory.spares.spring, compression.part no 70700 158 mandatory.spares.valve, check.part no 4913272 159 mandatory.spares.seal, o ring.part no 3034412 160 mandatory.spares.seal, o ring.part no 3021123 161 mandatory.spares.cap, fuel pump filter.part no 3014575 162 mandatory.spares.pump, sea water.part no 4912771 163 mandatory.spares.drive, generator.part no 2865786 164 mandatory.spares.pulley, idler.part no 3878763 165 mandatory.spares.actuator, etr fuel control.part no 3408326 166 mandatory.spares.pump, gear fuel.part no 3034246 167 mandatory.spares.flange, crankshaft.part no 213358 168 mandatory.spares.impeller, tur compressor.part no 3503456 169 mandatory.spares.shaft & wheel.part no 3500433 170 mandatory.spares.slinger, oil.part no 3759619 171 mandatory.spares.crankshaft kit.part no kit3881132 172 mandatory.spares.gear, flywheel ring.part no 124507 173 mandatory.spares.motor, air starting.part no 3026797 174 mandatory.spares.rod, engine connecting.part no 3023891...

Indian Navy - Andhra Pradesh

33380201 tender for 12k routines on g1 and g2 da ( vta 28 dm das ) in ship 1 12k routines. carry out a, b and c checks.vta1710.6000h1. vta28 dm. 2 12k routines. fuel system: ( a ) clean and calibrate injectors and record test pressures in service log. also change injector inlet screen. ( b ) replace rocker cover gaskets. ( c ) adjust valve tappet clearances within limits and record in service log. ( d ) replace fuel pump filter ( screen and magnet ) . ( e ) calibrate pt fuel pump and record in service log .6000h2. vta28 dm. 3 12k routines. air system: ( a ) clean turbocharger, compressor wheel and diffuser ( b ) check turbo charger radial / end bearing clearance in situ. note: renew o ring and teflon gasket when turbocharger is opened for checking clearances. 6000h3. vta28 dm. 4 12k routines. charge air cooler & fresh water cooler: ( a ) clean the internal passages of charge air cooler and fresh water cooler coolant side using restore plus as laid down in operating manual. ( b ) renew coolant in the system ( c ) inspect charge air cooler air side and if required clean using hot water and pressure test up to 2kg / cm2 6000h4. vta28 dm. 5 12k routines. other maintenance: ( a ) clean engine with solvent. ( b ) carryout flushing through of coolant system as per jic 6000h5. vta28 dm. 6 12k routines. check thickness of vibration damper at 0, 90, 180 and 270 degree positions. replace damper if variation of the 4 readings exceeds 0.010 inch ( 0.25mm ) or exceeds max allowable thickness. checks to be undertaken in coupled condition 6000h6. vta28 dm. 7 12k routines. check crank end clearances with a dial indicator, attaching against damper min 0.13 mm, max 0.51 mm. 6000h8. vta28 dm. 8 12k routines. tighten mounting bolts / nut as required. 6000h9. vta28 dm. 9 12k routines. for 1710 / 28gc1 engines undertake inspection of two representative pistons liners and bearings of the engine. inspection of balance liners and bearings is to be scheduled based on inspection report of the two sample liners. 6000h11. vta28 dm. 10 12k routines. carryout visual inspection of sv mounts. renew mounts if their condition is deteriorated. sr1. vta28 dm. 11 12k routines. undertake alignment checks between the generator and engine and restore radial / axial initial alignment to 25% of the max limit. sr2. vta28 dm. 12 12k routines. record crankshaft end clearances with a dial indicator, attaching against damper min 0.13 mm, max 0.51 mm when in coupled condition sr3. vta28 dm. 13 12k routines. check torque tightening of coupling inner / outer members as specified in the manual for das fitted with holset ( reynolds ) or centamax couplings. in case of vulcan couplings, check for cracks on rubber and if wear mark does not exceed limits. check tightness of adaptor plate bolts ( coupling bolts ) sr4. vta28 dm. 14 12k routines. check turbo charger radial / end bearing clearance in situ on removal of inlet / exhaust pipes. note: renew o ring and teflon gasket whenever t / c is opened for checking clearances. sr6. vta28 dm. 15 12k routines. offer performance assessment trials on external load tank to dttt / etma and vibration trials to mtu. crankcase blowby / engine smoke condition is also to be recorded along with all other performance parameters. trial teams to forward recommendations. 12000h2. vta28 dm. 16 12k routines. for 1710 / 28gc1 engines remove all cylinder heads for decarbonisation and inspect main / connecting rod bearing. undertake replacement of liners if pitting / corrosion observed on the extracted liners. refit cylinder heads and bearings as required 12000h3. vta28 dm. 17 12k routines. inspect holset / vulcan / centamax flexible coupling and torque tighten inner / outer members. check rubber blocks / disc for deterioration. renew if necessary. 12000h4. vta28 dm. 18 12k routines. undertake alignment checks between the generator and engine and restore radial / axial initial alignment to 25% of the max limit. 12000h5. vta28 dm. 19 12k routines. renew rubber vibration dampers where fitted. 12000h6. vta28 dm. 20 mandatory spares. liner, cylinder. part no. 3241328. 21 mandatory spares. nozzle, piston cooling. part no. 3044241. 22 mandatory spares. bearing, connecting rod. part no. 200600. 23 mandatory spares. bolt, connecting rod. part no. 146856. 24 mandatory spares. nut, heavy hexagon. part no. 69936. 25 mandatory spares. washer, plain. part no. 3025100. 26 mandatory spares. collet, valve. part no. 127554. 27 mandatory spares. guide, valve spring. part no. 170296. 28 mandatory spares. guide, valve spring. part no. 172034. 29 mandatory spares. spring, valve. part no. 211999. 30 mandatory spares. valve, intake. part no. 3803876. 31 mandatory spares. insert, valve. part no. 127930. 32 mandatory spares. guide, valve stem. part no. 3006456. 33 mandatory spares. insert, valve. part no. 3084185. 34 mandatory spares. sleeve, injector. part no. 3406702. 35 mandatory spares. seal, o ring. part no. 3007759. 36 mandatory spares. plug, expansion. part no. 3007636. 37 mandatory spares. plug, expansion. part no. 3007635. 38 mandatory spares. guide, valve crosshead. part no. 123558. 39 mandatory spares. retainer, valve spring. part no. 219091. 40 mandatory spares. plug, o ring. part no. 162143. 41 mandatory spares. screw, hexagon head cap. part no. 209700. 42 mandatory spares. screw, slotted set. part no. 168306. 43 mandatory spares. nut, regular hexagon. part no. s 212. 44 mandatory spares. screw, hexagon head cap. part no. 108601. 45 mandatory spares. screw, captive washer cap. part no. 3042889. 46 mandatory spares. rod, push. part no. 3046419. 47 mandatory spares. rod, push. part no. 3046432. 48 mandatory spares. thermostat. part no. 135675. 49 mandatory spares. seal, thermostat. part no. 186780. 50 mandatory spares. hose, plain. part no. 3017278. 51 mandatory spares. clamp, hose. part no. 43828 d. 52 mandatory spares. gasket, thermostat housing. part no. 102867. 53 mandatory spares. gasket, water manifold. part no. 102791. 54 mandatory spares. gasket, cover plate. part no. 124246. 55 mandatory spares. screw, hexagon head cap. part no. 120516. 56 mandatory spares. gasket, wtr trf connection. part no. 64413. 57 mandatory spares. kit, inj barrel plunger. part no. kit3238193. 58 mandatory spares. seal, o ring. part no. 193736. 59 mandatory spares. spring, compression. part no. 166009. 60 mandatory spares. ball, check. part no. 167157. 61 mandatory spares. gasket, injector. part no. 173086. 62 mandatory spares. retainer, screen. part no. 174299. 63 mandatory spares. pin, roll. part no. 203426. 64 mandatory spares. screen, filter. part no. 3054999. 65 mandatory spares. plug, injector orifice. part no. 3045047. 66 mandatory spares. retainer, injector cup. part no. 185138. 67 mandatory spares. clamp, injector. part no. 3031137. 68 mandatory spares. screw, twelve point cap. part no. 3028279. 69 mandatory spares. link, injector plunger. part no. 191916. 70 mandatory spares. kit, turbo repair 4lg. part no. 3545661. 71 mandatory spares. stud, double end plain. part no. 3042353. 72 mandatory spares. nut, regular hexagon. part no. 219138. 73 mandatory spares. gasket, turbocharger. part no. 3709749. 74 mandatory spares. gasket, turbocharger. part no. 3519763. 75 mandatory spares. gasket set. part no. kit3240239. 76 mandatory spares. gasket set vta 1710. part no. kit3247965. 77 mandatory spares. gasket, exhaust manifold. part no. 3081076. 78 mandatory spares. core, cooler. part no. 3010612. 79 mandatory spares. seal, o ring. part no. 3010617. 80 mandatory spares. gasket, lub oil clr hsg. part no. 172723. 81 mandatory spares. inhibitor, corrosion 10 liters. part no. 3167218. 82 mandatory spares. radiwash 3 liters. part no. ax1013359. 83 mandatory spares. pump, water. part no. 4911528. 84 mandatory spares. gasket, water pump. part no. 123078. 85 mandatory spares. gasket, water pump. part no. 69654. 86 mandatory spares. plug, zinc electrode. part no. 68241. 87 mandatory spares. gasket, heat exchanger. part no. 4009318. 88 mandatory spares. gasket, heat exchanger. part no. 4009319. 89 mandatory spares. seal, o ring. part no. 3011337. 90 mandatory spares. hose, plain. part no. 107063. 91 mandatory spares. clamp, hose. part no. 43828 f. 92 mandatory spares. hose, plain. part no. 102522. 93 mandatory spares. clamp, hose. part no. 43828 c. 94 mandatory spares. tank, expansion. part no. 4104977. 95 mandatory spares. hose, plain. part no. 4104834. 96 mandatory spares. clamp, t bolt. part no. 140315. 97 mandatory spares. tube, water makeup. part no. 4105019. 98 mandatory spares. gasket, heat exchanger. part no. 4104940. 99 mandatory spares. gauge, sight. part no. 4105897. 100 mandatory spares. clamp, t bolt. part no. 135144. 101 mandatory spares. hose, flexible. part no. ak 5040 ss. 102 mandatory spares. gasket, sea water pump. part no. 3055769. 103 mandatory spares. draincock. part no. 107947. 104 mandatory spares. gasket, water pump. part no. 69654. 105 mandatory spares. element, lub oil filter. part no. 3238204. 106 mandatory spares. filter, fuel. part no. 252193. 107 mandatory spares. kit, super byp.filter elem. part no. 3879488. 108 mandatory spares. seal, o ring. part no. 3010937. 109 mandatory spares. element, air cleaner. part no. 4020551. 110 mandatory spares. element, air cleaner. part no. 4020552. 111 mandatory spares. separator, fuel water. part no. 4912776. 112 mandatory spares. elbow, male union. part no. 129859. 113 mandatory spares. indicator, restriction. part no. 3872813. 114 mandatory spares. breather, crankcase. part no. 255180. 115 mandatory spares. hose, plain. part no. 3081053. 116 mandatory spares. hose, flexible. part no. ak10035 ss. 117 mandatory spares. hose, flexible. part no. ak 6030 ss. 118 mandatory spares. hose, flexible. part no. ak 6040 ss. 119 mandatory spares. hose, flexible. part no. ak10060 ss. 120 mandatory spares. hose, elbow. part no. 3235134. 121 mandatory spares. hose, hump. part no. 3235726. 122 mandatory spares. clamp, t bolt. part no. 125739. 123 mandatory spares. clamp, t bolt. part no. 125741. 124 mandatory spares. hose, flexible. part no. am16048 ss. 125 mandatory spares. hose, flexible. part no. am10040 ss. 126 mandatory spares. hose, flexible. part no. ak 5040 ss. 127 mandatory spares. hose, flexible. part no. am12028 ss. 128 mandatory spares. hose, flexible. part no. am 8120 ss. 129 mandatory spares. hose, flexible. part no. am 6065 ss. 130 mandatory spares. hose, flexible. part no. am 6045 ss. 131 mandatory spares. hose, flexible. part no. 3392424. 132 mandatory spares. hose, flexible. part no. ak 4120 ss. 133 mandatory spares. belt, v. part no. 3413583. 134 mandatory spares. gasket governor set. part no. kitbm68356. 135 mandatory spares. shaft, fuel pump drive. part no. 212601. 136 mandatory spares. shaft, tachometer drive. part no. 212607. 137 mandatory spares. diaphragm, ful pump damper. part no. 202897. 138 mandatory spares. valve, check. part no. 4913272. 139 mandatory spares. seal, o ring. part no. 3034412. 140 mandatory spares. spring, valve. part no. 129768. 141 mandatory spares. cover, fuel pump. part no. 3081372. 142 mandatory spares. bearing, ball. part no. s 16052. 143 mandatory spares. damper, fuel pump. part no. bm76340. 144 mandatory spares. carrier, governor weight. part no. 3006550. 145 mandatory spares. screen, filter. part no. 3090769. 146 mandatory spares. valve, shutoff. part no. 3096859. 147 mandatory spares. solenoid. part no. 3021420. 148 mandatory spares. seal, rectangular ring. part no. 154087. 149 mandatory spares. spider, jaw coupling. part no. 3046200. 150 mandatory spares. core, aftercooler. part no. 3026923. 151 mandatory spares. gasket, aft housing. part no. 3077201. 152 mandatory spares. gasket, wtr trf connection. part no. 215044. 153 mandatory spares. gasket, wtr trf connection. part no. 3032348. 154 mandatory spares. hose, plain. part no. 4957919. 155 mandatory spares. hose, plain. part no. 3027706. 156 mandatory spares. clamp, hose. part no. 3010550. 157 mandatory spares. clamp, hose. part no. 3026806. 158 mandatory spares. actuator, etr fuel control. part no. 3408326. 159 mandatory spares. pump, gear fuel. part no. 3034246. 160 mandatory spares. shaft & wheel. part no. 3500433. 161 mandatory spares. impeller, tur compressor. part no. 3503456. 162 mandatory spares. damper, vibration. part no. 3077985. 163 mandatory spares. camshaft. part no. 4073133. 164 mandatory spares. camshaft. part no. 4073134. 165 mandatory spares. bushing. part no. 70437. 166 mandatory spares. pump, lubricating oil. part no. 4979720. 167 mandatory spares. pump, sea water. part no. 4911777. 168 mandatory spares. tappet, injector. part no. 4071619. 169 mandatory spares. tappet, valve. part no. 4071615....

Indian Navy - Andhra Pradesh

31341299 procurement of diesel alternator spares for vta 28d 6bt 59dt 59d and prime , item , lever rocker , hose flexible , breather , gasket exh out connection , gauge sight , gauge temprature , gauge pressure , isolator, vibration , gauge pressure , hose flexible , hose assembly , connection water transfer , screw, socket set , pump, gear fuel , manifold exhaust , belt, vee , pump, water , gasket, connection , hose flexible , sprihose hump , connection exhaust outlet , turbocharger , seal water pump , bracket lifting , plug ball , gasket sea water pump , cover spring , core, aftercooler , seal dust , gasket rocker lever housing , gauge temprature , hose, flexible , tank, fuel transfer , gasket, connection , core cooler , exchanger, heat , clamp hose , hose, flexible , clamp, t bolt , tank, expansion , pump water , washer sealing , housing spring pack , seal grommet , vibration damper , cover fuel pump , screen, filter , hose elbow , starter air , belt, vee , pulley idler , pickup magnetic , hose flexible , screw captive washer cap , gasket connection , gasket turbocharger , clamp, hose , nut, regular hexagon , pickup, magnetic , cap, tappet top stop , seal rectangular ring , spring, injector , link, injector plunger , injector , clamp hose , washer, lock , retainer, screen , turbocharger , washer, plain , screw adjusting , sleeve , elbow male adoptor , seal, o ring , shim governor spring .005 , screw, hexagon head cap , spring, compression , nut lock , bushing camshaft , cap screw , gasket, wtr trf connection , housing spring pack , bearing, thrust , filter, lub oil bypass , washer plain , washer adjusting screw , switch , temperature , gasket gear cover plate , pin, roll , cap screw 1 / 2 13x3 1 / 2 , gasket, water trf conne , screw, hexagon head cap , nut , heat exchanger , gasket , seal , hose flexible , clip , gasket, connection , thermocouple , spring, compression , turbocharger , hose flexible , cover camshaft , hose flexible , hose, flexible , hose, flexible , screw, hexagon head cap , hose flexible , screw, twelve point cap , spring compression , dowel diamond , nut lock , rod engine conn , valve check , retainer, injector link , hose flexible , hose, plain , cup injector , nut lock , ring retaining , hose, plain , screw twelve point cap , gasket set, engine lower / upper set 3804300 / 3800731 , cover, hand hole , hose flexible , hose flexible , seal, o ring , retainer, shaft , hose flexible , spring, valve , gasket , seal, o ring , seal ring , gasket thermostat engine , shield for shut of valve , ball check , gear tacho , valve, check , plug injector orifice , hose, plain , piston ring set , radiwash_3ltr , gasket, oil pan , washer , washer thrust , connecting rod bearings , seal, o ring , resistor corrosion , seal kit , nut regular hexagon , gasket, cover plate , seal, o ring , washer plain , valve piston cooling , screw, twelve point cap , pump, lubricating oil , hose, plain , hose flexible , shaft & wheel , injector , clamp bolt for intake manifold , seal, rectangular strip , hose plan , vibration damper , inhibitor, corrosion ( premix 10 lt ) , gasket connection , valve, piston cooling , element lub oil filter , connection oil transfer , shaft, rockerlever , gasket turbocharger , seal, aftercooler core , guide, valve stem , plug expansion , camshaft , gasket, connection , oil pump , set, lower engine gasket , camshaft , gasket, rkr lever housing , injector , actuator etr fuel control , hose , gasket , switch magnetic 24v , clamp injector , gasket fuel pump , hose, flexible , spring , bolt , tachometer drive , kit engine piston , seal o ring , cap screen filter , idler water pump , crankshaft kit , screw, hex flange head cap , bushing , breather , washer, plain , screw, twelve point cap , liner cylinder , element, air cleaner , pump lubricating oil , tube water inlet , cable , key, plain woodruff , elbowmale adapter , support, bearing , support, bearing , washer, plain , pin roll , spacer crankshaft , gasket, wtr trf connection , element, air cleaner , gasket lub oil pump , pcb control , gasket end covers , washer thrust , oil seal , gasket oil pan , gasket, exhaust manifold , oil filter , gasket brg case , screw hexagon head cap , o ring , seal, o rings , seal o ring , seal o ring , seal ferrule , seal, o ring , cover, fuel pump front , clamp t bolt , gasket flange , screw flat head cap , bearing connecting rod , belt, v ribbed , elbow male adaptor , sleeve salvage , covar o ring , gasket turbocharger , assembly core , hose flexible , barrel & plunger , seal tank o ring , seal lta fitting o ring , hose flexible , kit engine piston , seal oring , hose flexible , hose, flexible , hose flexible , washer lock , cap screw , bearing, ball , hose flexible , bushing reducing pipe , bearing main , dc dc convertor make meanwell , sleeve injector , gasket heat exchanger , spacer mounting , hose flexible , clamp hose , pump lubricating oil , switch magnetic , tee mail union , washer sealing , seal o ring , seal, banjo connector , gasket, oil drain , rod, push , dowel ring , clamp hose , plug, zinc electrod , connector female , seal oil , impeller turbo compressor , seal injector , set upper engine gasket std , block, cylinder , tube fuel drain , clamp t bolt...

National Thermal Power Corporation Limited - Andhra Pradesh

30612702 procurement of mechanical seal assy spares for ntpc projects procurement of mechanical seal assy spares for ntpc projects , pto / pto:4.000 / 3.750:comp mech seal assy , aro :1.375:complete mech seal assly , aro :1.750:complete mech seal assly , ro:65mm:mech seal comp assy , fa1f56:gland gasket , fa1f56:spring# , fa1f56:shaft packing , fa1f56:compression unit , fa1f56:sleeve packing , fa1f56:sleeve , fa1f56:insert mating , fa1f56:seal ring , fa1f56:gland ring , 3h 19290 5.5:gasket: , 3h 19290 5.5:sleeve packing: , 3h 19290 5.5:insert mounting: , 3h 19290 5.5:seal ring: , 3h 19290 5.5:insert: , 3h 19290 5.5:shaft packing: , dhtw:6.750:sleeve gasket, 568358ad , dhtw:6.750:hhcs m12x60, 4n02129ck , dhtw:6.750:gland gasket, 568276ad , dhtw:6.750:hhcs m10x6, 4n04140ck , dhtw:6.750:coil spring, 0300 48 13 0 , dhtw:6.750:coil spring, 4n31723nl , dhtw:6.750:hhcs 3 / 8 16x3 / 4, 4r2893ck , dhtw:6.750:coil spring, 4r0083nl , dhtw:6.750:rotating face, c0020259x818 , dhtw:6.750:stationary face, 2n71845x851 , dhtw:6.750:pin, 4r3217x335 , dhtw:6.750:backing ring, 4r81267bo , dhtw:6.750:backing ring, 3n71833db , dhtw:6.750:backing ring gaskt, 568440x615 , dhtw:6.750:segmentd bushing, 024211056060 , dhtw:6.750:throat bushing, 3n71834ge , dhtw:6.750:vibration damper, 568170mg , dhtw:6.750:snap ring, ur750ck , dhtw:6.750:setting device, 4r8654db , dhtw:6.750:split ring, 3n71825db , dhtw:6.750:rotating face gaskt, 568166mge , dhtw:6.750:o ring gasket, 568372mg , dhtw:6.750:o ring gasket, 568166mg , dhtw:6.750:sscp 1 / 4 20 x1 / 2, 4ro429ci , qbl:85 lub:mech seal comp assy , qbl:w 48 lub:mech seal comp assy , qbl:w 48 lub:gasket , qbl:w 48 lub:set screw , qbl:w 48 lub:flange bushing , qbl:w 48 lub:gasket , qbl:w 48 lub:springholder , qbl:w 48 lub:coil spring , qbl:w 48 lub:seal face , qbl:w 48 lub:seal face , mech.seal:de / nde 4:dura weir fa1e64 , seal ring#3 dura mech.seal weir fa1e64 , insert ( carbon ) #2dur mechseal weir fa1e64 , compr.unit#45 dura 2h25254r3 weir fa1e64 , shaft pkg.#p dura mech.seal weir fa1e64 , sleevepkg.#11dura mechseal weirfa1e64 , gasket#g dura mech.seal weir fa1e64 , o ring#6 dura mech.seal weir fa1e64 => limited...

Indian Navy - Andhra Pradesh

29938331 mov/cpro/e1/21vkcc005 procurement of da spares for equipment model vta 28d(m) , item , belt, vee , seal of o ring , stop,thottle lever , gasket,connection , connection exhaust outlet , tank, fuel transfer , hose plain , tube water makeup , body shutoff valve , gasket connection , clamp, hose , housing spring pack , seal dust , core,aftercooler , flywheel , rod push , plug ball , manifold exhaust , pump, gear fuel , washer plain , belt,vee , seal grommet , valve,shutoff , gasket exh out connection , plunger fuel control , sprihose hump , isolator,vibration , pickup magnetic , gasket turbocharger , lever rocker , seal water pump , screen,filter , pulley idler , vibration damper , valve intake , clamp hose , tank, expansion , hose, flexible , exchanger, heat , core cooler , hose elbow , gasket,connection , hose , gasket exh out connection , gauge sight , clamp hose , pump, water , pump, fuel tln , core,aftercooler , seal o ring , valve collet , gasket,wtr trf connection , shaft,fuel pump drive , gasket breather , bearingr roller , gasket lub oil pump , seal,o ring , gasket,water pump , hose plain , gasket,thermostat housing , gasket, rkr lever housing , screen filter , valve,pressure regulator , cleaner air , clamp t bolt , element,air cleaner , element,air cleaner , cleaner,air , bushing camshaft , hose flexible , hose flexible , housing rkr 4 rm , bearing mainstd set...

Indian Navy - Andhra Pradesh

29771549 mov / cpro.e1 / 21vkcc003 mov / cpro.e1 / 21vkcc003 procurement of me diesel alternator , item , seal, rectangular ring , kit piston rings , o ring , sea water pump , impeller water pump , cap, tappet top stop , washer sealing , clamp hose , nut, tappet top stop lock , screw, injector stop , clamp t bolt , guide, valve stem , camshaft , vibration damper , injector , seal, aftercooler core , shaft & wheel , shaft, rockerlever , gasket, connection , gasket, lub oil cooler cover , hose plan , hose flexible , seal, rectangular strip , kit barel plunger & cup , camshaft , clamp bolt for intake manifold , kit turbo repair hc5a , hose, plain , vibration damper , plug expansion , gasket connection...

Indian Navy - Andhra Pradesh

28397538 concluding rate contract for routines on vta series cummins das in vessels , carry out a , b and c checks . vta1710 . 6000h1 . , fuel system: ( a ) clean and calibrate injectors and record test pressures in service log . also change injector inlet screen . ( b ) replace rocker cover gaskets . ( c ) adjust valve tappet clearances within limits and record in service log . ( d ) replace fuel pump filter ( screen and magnet ) . ( e ) calibrate pt fuel pump and record in service log . vta1710 . 6000h2 . , air system: ( a ) clean turbocharger , compressor wheel and diffuser ( b ) check turbo charger radial / end bearing clearance in situ . note: renew o ring and teflon gasket when turbocharger is opened for checking clearances . vta1710 . 6000h3 . , charge air cooler & fresh water cooler: ( a ) clean the internal passages of charge air cooler and fresh water cooler coolant side using restore plus as laid down in operating manual . ( b ) renew coolant in the system ( c ) inspect charge air cooler air side and if required clean using hot water and pressure test up to 2kg / cm2 . vta1710 . 6000h4 . , other maintenance: ( a ) clean engine with solvent . ( b ) carryout flushing through of coolant system as per jic vta1710 . 6000h5 . , check thickness of vibration damper at 0 , 90 , 180 and 270 degree positions . replace damper if variation of the 4 readings exceeds 0 . 010 inch ( 0 . 25mm ) or exceeds max allowable thickness . checks to be undertaken in coupled condition . vta1710 . 6000h6 . , check all safety alarms and trips . vta1710 . 6000h7 . , check crank end clearances with a dial indicator , attaching against damper min 0 . 13 mm , max 0 . 51 mm . vta1710 . 6000h8 . , tighten mounting bolts / nut as required . vta1710 . 6000h9 . , for 1710 / 28gc1 engines undertake inspection of two representative pistons liners and bearings of the engine . inspection of balance liners and bearings is to be scheduled based on inspection report of the two sample liners . vta1710 . 6000h11 . , carryout visual inspection of sv mounts . renew mounts if their condition is deteriorated . vta1710 . sr1 . , undertake alignment checks between the generator and engine and restore radial / axial initial alignment to 25% of the max limit . vta1710 . sr2 . , record crankshaft end clearances with a dial indicator , attaching against damper min 0 . 13 mm , max 0 . 51 mm when in coupled condition . vta1710 . sr3 . , check torque tightening of coupling inner / outer members as specified in the manual for das fitted with holset ( reynolds ) or centamax couplings . in case of vulcan couplings , check for cracks on rubber and if wear mark does not exceed limits . check tightness of adaptor plate bolts ( coupling bolts ) vta1710 . sr4 . , in case of 743 / 855 engines . check thickness of vibration damper at 0 , 90 , 180 and 270 degree positions . replace damper if variation of the 4 readings exceeds . 0 . 010 inch ( 0 . 25mm ) or exceeds max allowable thickness . checks to be undertaken in coupled condition . vta1710 . sr5 . , check turbo charger radial / end bearing clearance in situ on removal of inlet / exhaust pipes . note: renew o ring and teflon gasket whenever t / c is opened for checking clearances . vta1710 . sr6 . , carry out a , b , c , d and sr checks . vta1710 . 12000h1 . , offer performance assessment trials on external load tank to dttt / etma and vibration trials to mtu . crankcase blowby / engine smoke condition is also to be recorded along with all other performance parameters . trial teams to forward recommendations . vta1710 . 12000h2 . , for 1710 / 28gc1 engines remove all cylinder heads for decarbonisation and inspect main / connecting rod bearing . undertake replacement of liners if pitting / corrosion observed on the extracted liners . refit cylinder heads and bearings as requiredvta1710 . 12000h3 . , inspect holset / vulcan / centamax flexible coupling and torque tighten inner / outer members . check rubber blocks / disc for deterioration . renew if necessary . vta1710 . 12000h4 . , undertake alignment checks between the generator and engine and restore radial / axial initial alignment to 25% of the max limit . vta1710 . 12000h5 . , renew rubber vibration dampers where fitted . vta1710 . 12000h6 . , dismantle auxiliary drives and check bearing clearances . renew bearings if necessary . examine all gear teeth for pitting and scuffing . vta1710 . 24000h1 . , renew big end bearings , their bolts , nuts and washers . vta1710 . 24000h2 . , check main bearing clearances and examine the condition . renew bearing if clearances are excessive . vta1710 . 24000h3 . , remove , clean and examine all cylinder liners for scoring and corrosion . gauge liners internally . renew if necessary . vta1710 . 24000h4 . , clean all water passages . renew all sealing rings . vta1710 . 24000h5 . , examine and gauge all pistons . renew pistons if necessary . vta1710 . 24000h6 . , renew all piston rings . vta1710 . 24000h7 . , remove crankshaft and check for cracks , scoring and deflection , ( eccentricity ) . clean and flush out oil ways . renew teflon seals . vta1710 . 24000h8 . , overhaul governor . renew worn out parts . calibrate governor after completion of overhauling . vta1710 . 24000h9 . , ( a ) remove and chemically clean lub oil cooler and fresh water cooler and carry out pressure testing . replace if required . ( b ) renew gasket and `o seals . vta1710 . 24000h10 . , remove and check the over speed trip ( protection device / sensor ) for correct setting / functioning , calibrate if necessary . vta1710 . 24000h11 . , refit cam shaft drive assembly . vta1710 . 24000h12 . , check all camshaft bearing clearances . renew if necessary . check valve timing . vta1710 . 24000h13 . , check all connecting rods for bend and twist . clean and flush out oil passages . vta1710 . 24000h14 . , renew hp fuel pump . vta1710 . 24000h15 . , remove , clean and retreat the crankcase . vta1710 . 24000h16 . , clean and repaint bedplate . vta1710 . 24000h17 . , renew all flexible hoses . vta1710 . 24000h18 . , gauge all gudgeon pins . replace if wear is excessive . vta1710 . 24000h19 . , renew s . v . mountings . vta1710 . 24000h20 . , overhaul turbo supercharger . renew entire unit if parts are excessively worn out . vta1710 . 24000h21 . , remove air cooler , chemically clean and pressure test on completion of cleaning . replace if required . vta1710 . 24000h22 . , overhaul air starting motor . renew worn partsvta1710 . 24000h23 . , renew silicon vibration damper where fitted . vta1710 . 24000h24 . , overhaul / renew holset / vulcan / centamax coupling as necessary . renew the rubber inserts / member of the flexible coupling . renew all fasteners / bolts while assembling the coupling as per oem recommended procedure . carry out engine to alternator alignment procedure while maintaining the crankshaft end clearances . dowel the alternator . carry out full load trials and vibration checks before normal service . vta1710 . 24000h25 . , carry out a , b and c checks . vta28dm . 6000h1 . , fuel system: ( a ) clean and calibrate injectors and record test pressures in service log . also change injector inlet screen . ( b ) replace rocker cover gaskets . ( c ) adjust valve tappet clearances within limits and record in service log . ( d ) replace fuel pump filter ( screen and magnet ) . ( e ) calibrate pt fuel pump and record in service log . vta28dm . 6000h2 . , air system: ( a ) clean turbocharger , compressor wheel and diffuser ( b ) check turbo charger radial / end bearing clearance in situ . note: renew o ring and teflon gasket when turbocharger is opened for checking clearances . vta28dm . 6000h3 . , charge air cooler & fresh water cooler: ( a ) clean the internal passages of charge air cooler and fresh water cooler coolant side using restore plus as laid down in operating ma...

Hindustan Shipyard Limited - Andhra Pradesh

28393339 overhauling of auxiliary engines on mv swaraj dweep , the following routines is to be carriedout on auxilliary engines no . 4 & no . 5 as per sow to the satisfaction of ss & hsl . post completion of routines and entire assembly of engine , satisfacotry full load trials to be offered to ss & hsl . defects if any observed by ship staff to be liquidated and trials to be reoffered to the satisfaction of ss & hsl . all measuring instruments , consumables and weldind / brazing / grinding works are covered in contractors scope . , uxilliary engine no . 4 , make : man b&w , ssangyong 6l 28/32h , 1600 bhp hyundai , 1999a , 390v , ae 4 gear case inspection doors to be opened and all gears to be inspected . gears backlash to be checked and recorded . after the satisfactory inspection of gear case , inspection doors to be boxed back with new joints . , ae 4 vibration damper inspection doors to be opened and damper to be inspected . vibration damper clearances to be taken and recorded . after satisfactory inspection , doors to be boxed back with new joints . , auxilliary engine no . 5 , the following jobs is to carry out on aux engine 5 . presently the engine is with removed pistons along with con rods and removed attached pumps . , all liners , pistons , connecting rods , piston pins are to clean and to calibrate to check for ovality , dp test to be carried out for crack detection , and to be shown to surveyors . post checks all components to be assembled back with ship supplied spares and all bottom end bearings to be replaced and tightened , all clearances and web deflections to be measured and recorded , renewal of one liner . ( liner ships supply ) , renewal of one piston ( piston ships supply . ) , renewal of one con rod ( con . rod ships supply . ) , all six crank pins to polish and specially attention to pay on the pins which are embedded with wiped out bearing white metal . , #2 unit pin to go grinding for 1 . 0mm under size . , after necessary repairs , the crank shaft pins hardness to be tested . , front gear case cover to remove from place and extract broken drive gear wheel from the main crank shaft . new drive gear wheel ( ships supply ) to fix in place , gear backlash to be taken for all gears in gear case and same to be recorded , front gear wheel cover to box back and mount attached fresh water cooling pump and lube oil pump . , attached lube oil gear pump and fresh water pump to overhaul . all damaged and worn out parts to replace with spare ones supplied by ships staff . satisfactory trials to be shown to ss . , all six cylinder heads to be mounted in place with new joints , gaskets and o rings . holding down nuts to be tightened as per oems ( manual ) , after completion of all jobs in all respects , cooling water to try out . while trying out cooling water circuit , leaks to be rectified and satisfactory condition to be shown to ship staff . crank case oil around 800 ltrs to remove and disposed off . crank case to clean to ship staff satisfaction and fresh oil to take . old lub oil from lo filters & lo cooler to be drained and cleaned . lub oil ship supply . , ae 5 vibration damper inspection doors to be opened and damper to be inspected . vibration damper clearances to be taken and recorded . after satisfactory inspection , doors to be boxed back with new joints . , all safety cut outs ae 5 to be tried out and defect to be rectified by changing with suitable cutout along with required cabling and system to be proved and satisfactory trials to be shown to the ss/surveyors & hsl . ...

Indian Navy - Andhra Pradesh

28275906 rate contract for routines on nt series cummins das in vessels rate contract for routines on nt series cummins das in vessels , carry out a , b and c checks . nt495 . 6000h1 . , fuel system: ( a ) clean and calibrate injectors and record test pressures in service log . also change injector inlet screen . ( b ) replace rocker cover gaskets . ( c ) adjust valve tappet clearances within limits and record in service log . ( d ) replace fuel pump filter ( screen and magnet ) . ( e ) calibrate pt fuel pump and record in service log . nt495 . 6000h2 . , air system: ( a ) clean turbocharger , compressor wheel and diffuser ( b ) check turbo charger radial/end bearing clearance in situ . note: renew o ring and teflon gasket when turbocharger is opened for checking clearances . nt495 . 6000h3 . , charge air cooler & fresh water cooler: ( a ) clean the internal passages of charge air cooler and fresh water cooler coolant side using restore plus as laid down in operating manual . ( b ) renew coolant in the system ( c ) inspect charge air cooler air side and if required clean using hot water and pressure test up to 2kg/cm2 . nt495 . 6000h4 . , other maintenance: ( a ) clean engine with solvent . ( b ) carryout flushing through of coolant system as per jic nt495 . 6000h5 . , check thickness of vibration damper at 0 , 90 , 180 and 270 degree positions . replace damper if variation of the 4 readings exceeds 0 . 010 inch ( 0 . 25mm ) or exceeds max allowable thickness . checks to be undertaken in coupled condition . nt495 . 6000h6 . , check all safety alarms and trips . nt495 . 6000h7 . , check crank end clearances with a dial indicator , attaching against damper min 0 . 13 mm , max 0 . 51 mm . nt495 . 6000h8 . , tighten mounting bolts/nut as required . nt495 . 6000h9 . , alignment checks: ( for nt/nta 855 series engines ) undertake alignment checks between the generator and engine and restore radial/axial initial alignment to 25% of the max limit . nt495 . 6000h10 . , carryout visual inspection of sv mounts . renew mounts if their condition is deteriorated . nt495 . sr1 . , undertake alignment checks between the generator and engine and restore radial/axial initial alignment to 25% of the max limit . nt495 . sr2 . , record crankshaft end clearances with a dial indicator , attaching against damper min 0 . 13 mm , max 0 . 51 mm when in coupled condition . nt495 . sr3 . , check torque tightening of coupling inner/outer members as specified in the manual for das fitted with holset ( reynolds ) or centamax couplings . in case of vulcan couplings , check for cracks on rubber and if wear mark does not exceed limits . check tightness of adaptor plate bolts ( coupling bolts ) nt495 . sr4 . , in case of 743/855 engines . check thickness of vibration damper at 0 , 90 , 180 and 270 degree positions . replace damper if variation of the 4 readings exceeds . 0 . 010 inch ( 0 . 25mm ) or exceeds max allowable thickness . checks to be undertaken in coupled condition . nt495 . sr5 . , check turbo charger radial/end bearing clearance in situ on removal of inlet/exhaust pipes . note: renew o ring and teflon gasket whenever t/c is opened for checking clearances . nt495 . sr6 . , carry out a , b , c , d and sr checks . nt495 . 12000h1 . , offer performance assessment trials on external load tank to dttt/etma and vibration trials to mtu . crankcase blowby/engine smoke condition is also to be recorded along with all other performance parameters . trial teams to forward recommendations . nt495 . 12000h2 . , undertake random inspection of two representative liners and bearings of the engine . inspect other liners/bearings incase deteriorated . following inspection and examination cylinders to be carried out: ( a ) gauging and inspection of one liner from each bank for corrosion/pitting post extraction . ( b ) gauging of connecting rod big end bearing clearances and examination of big end shell for the cylinder opened . ( c ) check condition of valve gear bracket , transfer sleeve sealing ring and injector tube . inspection of valve gear parts and valve seat inserts of the cylinder head opened . ( d ) examine crank pin surfaces and check for ovality and wear . ( e ) examine pistons for wear and gauge piston ring clearances . renew rings if necessary . ( f ) examine lub oil pump drive for wear . nt495 . 12000h3 . , inspect holset/vulcan/centamax flexible coupling and torque tighten inner/outer members . check rubber blocks/disc for deterioration . renew if necessary . nt495 . 12000h4 . , undertake alignment checks between the generator and engine and restore radial/axial initial alignment to 25% of the max limit . nt495 . 12000h5 . , renew rubber vibration dampers where fitted . nt495 . 12000h6 . , dismantle auxiliary drives and check bearing clearances . renew bearings if necessary . examine all gear teeth for pitting and scuffing . nt495 . 24000h1 . , renew big end bearings , their bolts , nuts and washers . nt495 . 24000h2 . , check main bearing clearances and examine the condition . renew bearing if clearances are excessive . nt495 . 24000h3 . , remove , clean and examine all cylinder liners for scoring and corrosion . gauge liners internally . renew if necessary . nt495 . 24000h4 . , clean all water passages . renew all sealing rings . nt495 . 24000h5 . , examine and gauge all pistons . renew pistons if necessary . nt495 . 24000h6 . , renew all piston rings . nt495 . 24000h7 . , remove crankshaft and check for cracks , scoring and deflection , ( eccentricity ) . clean and flush out oil ways . renew teflon seals . nt495 . 24000h8 . , overhaul governor . renew worn out parts . calibrate governor after completion of overhauling . nt495 . 24000h9 . , ( a ) remove and chemically clean lub oil cooler and fresh water cooler and carry out pressure testing . replace if required . ( b ) renew gasket and `o seals . nt495 . 24000h10 . , remove and check the over speed trip ( protection device/ sensor ) for correct setting/functioning , calibrate if necessary . nt495 . 24000h11 . , refit cam shaft drive assembly . nt495 . 24000h12 . , check all camshaft bearing clearances . renew if necessary . check valve timing . nt495 . 24000h13 . , check all connecting rods for bend and twist . clean and flush out oil passages . nt495 . 24000h14 . , renew hp fuel pump . nt495 . 24000h15 . , remove , clean and retreat the crankcase . nt495 . 24000h16 . , clean and repaint bedplate . nt495 . 24000h17 . , renew all flexible hoses . nt495 . 24000h18 . , gauge all gudgeon pins . replace if wear is excessive . nt495 . 24000h19 . , renew s . v . mountings . nt495 . 24000h20 . , overhaul turbo supercharger . renew entire unit if parts are excessively worn out . nt495 . 24000h21 . , remove air cooler , chemically clean and pressure test on completion of cleaning . replace if required . nt495 . 24000h22 . , overhaul air starting motor . renew worn partsnt495 . 24000h23 . , renew silicon vibration damper where fitted . nt495 . 24000h24 . , overhaul/renew holset/vulcan/centamax coupling as necessary . renew the rubber inserts/ member of the flexible coupling . renew all fasteners /bolts while assembling the coupling as per oem recommended procedure . carry out engine to alternator alignment procedure while maintaining the crankshaft end clearances . dowel the alternator . carry out full load trials and vibration checks before normal service . nt495 . 24000h25 . , carry out a , b and c checks . nt855 . 6000h1 . , fuel system: ( a ) clean and calibrate injectors and record test pressures in service log . also change injector inlet screen . ( b ) replace rocker cover gaskets . ( c ) adjust valve tappet clearances within limits and record in service log . ( d ) replace fuel pump filter ( screen and magnet ) . ( e ) calibrate pt fuel p...

Indian Navy - Andhra Pradesh

28275897 rate contract for routines on kta series cummins das in vessels , carry out a , b and c checks . 6000h1 . kta50g3 . , fuel system: ( a ) clean and calibrate injectors and record test pressures in service log . also change injector inlet screen . ( b ) replace rocker cover gaskets . ( c ) adjust valve tappet clearances within limits and record in service log . ( d ) replace fuel pump filter ( screen and magnet ) . ( e ) calibrate pt fuel pump and record in service log . 6000h2 . kta50g3 . , air system: ( a ) clean turbocharger , compressor wheel and diffuser ( b ) check turbo charger radial / end bearing clearance in situ . note: renew o ring and teflon gasket when turbocharger is opened for checking clearances . 6000h3 . kta50g3 . , charge air cooler & fresh water cooler: ( a ) clean the internal passages of charge air cooler and fresh water cooler coolant side using restore plus as laid down in operating manual . ( b ) renew coolant in the system ( c ) inspect charge air cooler air side and if required clean using hot water and pressure test up to 2kg / cm2 . 6000h4 . kta50g3 . , other maintenance: ( a ) clean engine with solvent . ( b ) carryout flushing through of coolant system as per jic 6000h5 . kta50g3 . , check thickness of vibration damper at 0 , 90 , 180 and 270 degree positions . replace damper if variation of the 4 readings exceeds 0 . 010 inch ( 0 . 25mm ) or exceeds max allowable thickness . checks to be undertaken in coupled condition . 6000h6 . kta50g3 . , check all safety alarms and trips . 6000h7 . kta50g3 . , check crank end clearances with a dial indicator , attaching against damper min 0 . 13 mm , max 0 . 51 mm . 6000h8 . kta50g3 . , tighten mounting bolts / nut as required . 6000h9 . kta50g3 . , alignment checks: ( for nt / nta 855 series engines ) undertake alignment checks between the generator and engine and restore radial / axial initial alignment to 25% of the max limit . 6000h10 . kta50g3 . , carryout visual inspection of sv mounts . renew mounts if their condition is deteriorated . sr1 . kta50g3 . , undertake alignment checks between the generator and engine and restore radial / axial initial alignment to 25% of the max limit . sr2 . kta50g3 . , record crankshaft end clearances with a dial indicator , attaching against damper min 0 . 13 mm , max 0 . 51 mm when in coupled condition . sr3 . kta50g3 . , check torque tightening of coupling inner / outer members as specified in the manual for das fitted with holset ( reynolds ) or centamax couplings . in case of vulcan couplings , check for cracks on rubber and if wear mark does not exceed limits . check tightness of adaptor plate bolts ( coupling bolts ) sr4 . kta50g3 . , in case of 743 / 855 engines . check thickness of vibration damper at 0 , 90 , 180 and 270 degree positions . replace damper if variation of the 4 readings exceeds . 0 . 010 inch ( 0 . 25mm ) or exceeds max allowable thickness . checks to be undertaken in coupled condition . sr5 . kta50g3 . , check turbo charger radial / end bearing clearance in situ on removal of inlet / exhaust pipes . note: renew o ring and teflon gasket whenever t / c is opened for checking clearances . sr6 . kta50g3 . , carry out a , b , c , d and sr checks . 12000h1 . kta50g3 . , offer performance assessment trials on external load tank to dttt / etma and vibration trials to mtu . crankcase blowby / engine smoke condition is also to be recorded along with all other performance parameters . trial teams to forward recommendations . 12000h2 . kta50g3 . , undertake random inspection of two representative liners and bearings of the engine . inspect other liners / bearings incase deteriorated . following inspection and examination cylinders to be carried out: ( a ) gauging and inspection of one liner from each bank for corrosion / pitting post extraction . ( b ) gauging of connecting rod big end bearing clearances and examination of big end shell for the cylinder opened . ( c ) check condition of valve gear bracket , transfer sleeve sealing ring and injector tube . inspection of valve gear parts and valve seat inserts of the cylinder head opened . ( d ) examine crank pin surfaces and check for ovality and wear . ( e ) examine pistons for wear and gauge piston ring clearances . renew rings if necessary . ( f ) examine lub oil pump drive for wear . 12000h3 . kta50g3 . , inspect holset / vulcan / centamax flexible coupling and torque tighten inner / outer members . check rubber blocks / disc for deterioration . renew if necessary . 12000h4 . kta50g3 . , undertake alignment checks between the generator and engine and restore radial / axial initial alignment to 25% of the max limit . 12000h5 . kta50g3 . , renew rubber vibration dampers where fitted . 12000h6 . kta50g3 . , dismantle auxiliary drives and check bearing clearances . renew bearings if necessary . examine all gear teeth for pitting and scuffing . 24000h1 . kta50g3 . , renew big end bearings , their bolts , nuts and washers . 24000h2 . kta50g3 . , check main bearing clearances and examine the condition . renew bearing if clearances are excessive . 24000h3 . kta50g3 . , remove , clean and examine all cylinder liners for scoring and corrosion . gauge liners internally . renew if necessary . 24000h4 . kta50g3 . , clean all water passages . renew all sealing rings . 24000h5 . kta50g3 . , examine and gauge all pistons . renew pistons if necessary . 24000h6 . kta50g3 . , renew all piston rings . 24000h7 . kta50g3 . , remove crankshaft and check for cracks , scoring and deflection , ( eccentricity ) . clean and flush out oil ways . renew teflon seals . 24000h8 . kta50g3 . , overhaul governor . renew worn out parts . calibrate governor after completion of overhauling . 24000h9 . kta50g3 . , ( a ) remove and chemically clean lub oil cooler and fresh water cooler and carry out pressure testing . replace if required . ( b ) renew gasket and `o seals . 24000h10 . kta50g3 . , remove and check the over speed trip ( protection device / sensor ) for correct setting / functioning , calibrate if necessary . 24000h11 . kta50g3 . , refit cam shaft drive assembly . 24000h12 . kta50g3 . , check all camshaft bearing clearances . renew if necessary . check valve timing . 24000h13 . kta50g3 . , check all connecting rods for bend and twist . clean and flush out oil passages . 24000h14 . kta50g3 . , renew hp fuel pump . 24000h15 . kta50g3 . , remove , clean and retreat the crankcase . 24000h16 . kta50g3 . , clean and repaint bedplate . 24000h17 . kta50g3 . , renew all flexible hoses . 24000h18 . kta50g3 . , gauge all gudgeon pins . replace if wear is excessive . 24000h19 . kta50g3 . , renew s . v . mountings . 24000h20 . kta50g3 . , overhaul turbo supercharger . renew entire unit if parts are excessively worn out . 24000h21 . kta50g3 . , remove air cooler , chemically clean and pressure test on completion of cleaning . replace if required . 24000h22 . kta50g3 . , overhaul air starting motor . renew worn parts24000h23 . kta50g3 . , renew silicon vibration damper where fitted . 24000h24 . kta50g3 . , overhaul / renew holset / vulcan / centamax coupling as necessary . renew the rubber inserts / member of the flexible coupling . renew all fasteners / bolts while assembling the coupling as per oem recommended procedure . carry out engine to alternator alignment procedure while maintaining the crankshaft end clearances . dowel the alternator . carry out full load trials and vibration checks before normal service . 24000h25 . kta50g3 . , carry out a , b and c checks . 6000h1 . kta50dm . , fuel system: ( a ) clean and calibrate injectors and record test pressures in service log . also change injector inlet screen . ( b ) replace rocker cover gaskets . ( c ) adjust valve tappet clearances within limits and record in service log . ( d ) replace fuel pump filter ( screen and magnet...

Indian Navy - Andhra Pradesh

27011501 supply of 24k routines on bmes in ship 1 bme.carry out following as part of 24000 hrly routine ( major ovehaul ) on both main engine.16pa6v 280 2 bme.dismantle complete engine and check crank shaft wear. grind the crank pins and journals. note: job will be done as : check and measure diamensions of crankpins and journals of crank shaft. carry out cam wears measurement on cranpins..16pa6v 280 3 bme.replace crack shaft bearing shells and thrust collars.16pa6v 280 4 bme.check cam shaft shaft journals and cam. examine cam shaft bearing bushes. renew if necessary. renew cam followers and push rods.16pa6v 280 5 bme.carryout complete cleaning and inspection of crank case, internally and externally, with crank shaft in place. note: dp test on crankcase ( at 4 points only ) 1. liner bore, 2. all gears of gear train ( except water pump gear ) , .16pa6v 280 6 bme.change all full flow and diversion element of lub oil filter hydraulic motor.16pa6v 280 7 bme.renew big end bearing and small end bearing and gudgeon pins.16pa6v 280 8 bme.descale all cylinder liners and renew sealing rings. examine upper flange. note: ( no rehoning of liners consided ) .16pa6v 280 9 bme.renew idle pinion roller bearings of timing gear train..16pa6v 280 10 bme.inspect vibration damper. renew bushes and springs..16pa6v 280 11 bme.overhaul and carry out timing, phasing and calibration of fuel injection pump.16pa6v 280 12 bme.overhaul lub oil pump. reset safety valve..16pa6v 280 13 bme.overhaul fresh water and sea water pumps. renew bearing and seals. inspect drive pinion. replace unit if necessary.16pa6v 280 14 bme.replace all springs of gieslinger coupling and friction bush.16pa6v 280 15 bme.overhaul turning gear mechanism.16pa6v 280 16 bme.clean glacier centrifuge purifier and “moatti” filter.16pa6v 280 17 bme.test the injectors for spray, seat tightness and automisation and carry out calibration.16pa6v 280 18 bme.check and reset tappet clearance under cold condition.16pa6v 280 19 bme.measure and record crank shaft deflection.16pa6v 280 20 bme.overhaul fuel booster pump. replace serrated bush of pump drive. renew all seals and joints.16pa6v 280 21 bme.inspect piston and connecting rod for serviceabilty. renew as necessary. replace all piston rings and measure clearances inside their grooves.16pa6v 280 22 bme.overhaul complete turbo charger unit, renew bearings, sealing rings and bushes..16pa6v 280 23 bme. ( aj ) overhaul the air distributor disc and air starting valves. renew air starting valves.16pa6v 280 24 bme. ( ak ) overhaul over speed trip slide valve and replace seals..16pa6v 280 25 bme. ( al ) overhaul cylinder heads, decorbonise, descale coolant passage. replace cylinder head gaket. check for serviceability replace if necessary. renew rocker arm bushes and tappets. replace inlet and exhaust valves. renew valve bridges. recondition the e.16pa6v 280 26 bme.check valves and rings of air stating valve. renew if necessary.16pa6v 280 27 bme.check for zero error of fuel rack on engine and correct as required.16pa6v 280 28 bme.renew seal of fuel linkage rods. check link rods for bending and adjust dead rack position.16pa6v 280 29 bme.inspect / overhaul speed governor and carry out bench test.16pa6v 280 30 bme.removal & fitment of governor assly.16pa6v 280 31 bme.overhaling & calibaration of governor assly carry out bench test. note: governor transportation / packing to be arranged by yard / ss ) .16pa6v 280 32 bme.check teething and serration clearance and backlash of governor drive.16pa6v 280 33 bme.renew sv mounts. note: the job involves renewal of mount and carrying out engine alignment with respect to gear box. work on girder, machine, chock supply, welding, cutting, system piping removal / refitment, in yard scope ) .16pa6v 280 34 bme.chemically clean and pressure test lub oil coolers. rectify the defects if any..16pa6v 280 35 bme.replace rings of expansion joints of exhaust manifold of main engine to clean & realign.16pa6v 280 36 bme.chemically clean charge air cooler fresh water side and air space side, pressure test for leaks repair defects..16pa6v 280 37 bme.renew all rubber hoses bellow 250 mm 02 nos . change all flexible hoses.16pa6v 280 38 bme.dismantle and clean the thermostat valve replace as necessary.16pa6v 280 39 bme.chemical cleaning and pressure test of fresh water cooler rectify the defects if any. job to be done as follow.16pa6v 280 40 bme.replace two way pneumatic valve of fuel circuit..16pa6v 280 41 bme.check over speed trip at no load. ( gestra valve to be overhauled ) ..16pa6v 280 42 mandatory spares.roller bearing.74.266.16.0.00 43 mandatory spares.o ring.79.068.20.0.00 44 mandatory spares.punched joint.74.105.12.0.00 45 mandatory spares.punched gasket.74.105.18.0.00 46 mandatory spares.joint.74.105.23.0.00 47 mandatory spares.joint for balmo fuel feed pump.74.421.02.0.00 48 mandatory spares.bush for fuel booster pump.74.326.41.0.00 49 mandatory spares.hose pipe.72.115.24.0.00 50 mandatory spares.hose clip ( 30 mm ) for 48.019.02.0.00, 40.149.02.0.00.50.519.06.000. 51 mandatory spares.flex.hose.74.381.02.0.00 52 mandatory spares.rubber compensating sleeve.74.381.64.0.00 53 mandatory spares.rubber compensating sleeve.74.381.68.0.00 54 mandatory spares.rubber compensating sleeve.74.381.70.0.00 55 mandatory spares.breather o / l conn. bank a / b.74.381.98.0.00 56 mandatory spares.rubber compensating sleeve.74.381.72.0.00 57 mandatory spares.rubber compensating sleeve.75.267.23.0.00 58 mandatory spares.rubber compensating sleeve.74.381.77.0.00 59 mandatory spares.flex hose.74.381.21.0.00 60 mandatory spares.rubber compensating sleeve.74.381.81.0.00 61 mandatory spares.rubber compensating sleeve.74.381.82.0.00 62 mandatory spares.flex hose.74.381.26.0.00 63 mandatory spares.flex hose.74.381.29.0.00 64 mandatory spares.flex hose.74.381.33.0.00 65 mandatory spares.flexible hose.74.381.34.0.00 66 mandatory spares.flexible hose.74.381.39.0.00 67 mandatory spares.flexible hose.74.381.45.0.00 68 mandatory spares.flex hose.74.381.36.0.00 69 mandatory spares.set of gaskets for lub oil filter housing.74.386.78.0.00 70 mandatory spares.o ring.79.160.07.0.00 71 mandatory spares.ball bearing for lub oil filter.74.386.67.0.00 72 mandatory spares.ball bearing for hyd. motor.74.306.83.0.00 73 mandatory spares.bearing bushes.79.053.19.0.00 74 mandatory spares.uniball joint female socket type.79.056.18.0.00 75 mandatory spares.oval gasket.74.263.02.0.00 76 mandatory spares.stop ring.79.053.17.0.00 77 mandatory spares.coupling ring.79.053.18.0.00 78 mandatory spares.bearing bush.74.262.06.0.00 79 mandatory spares.bearing bush.74.262.07.0.00 80 mandatory spares.simrit ring.74.262.08.0.00 81 mandatory spares.copper washer ( 18x24 ) .50.508.17.000. 82 mandatory spares.o ring.74.265.05.0.00 83 mandatory spares.joint.74.265.06.0.00 84 mandatory spares.gasket.74.356.34.0.00 85 mandatory spares.o ring.79.160.07.0.00 86 mandatory spares.o ring.74.402.21.0.00 87 mandatory spares.o ring.74.402.11.0.00 88 mandatory spares.o ring.74.402.10.0.00 89 mandatory spares.reinforced thrust bearing.74.007.04.0.00 90 mandatory spares.o ring.79.101.03.0.00 91 mandatory spares.o ring.79.101.04.0.00 92 mandatory spares.copper washer ( 12x18 ) .50.508.10.000. 93 mandatory spares.gasket.74.352.21.0.00 94 mandatory spares.o ring.74.065.17.0.00 95 mandatory spares.joint.74.159.13.0.00 96 mandatory spares.joint.74.159.12.0.00 97 mandatory spares.o ring.79.149.13.0.00 98 mandatory spares.o ring.79.160.07.0.00 99 mandatory spares.gasket.74.389.14.0.00 100 mandatory spares.copper washer ( 30x38 ) .50.508.35.000. 101 mandatory spares.joint.75.312.08.0.00 102 mandatory spares.copper washer ( 14x18 ) .50.508.11.000. 103 mandatory spares.o ring.79.046.28.0.00 104 mandatory spares.o ring.71.067.33.0.00 105 mandatory spares.o ring.74.411.06.0.00 106 mandatory spares.o ring.79.068.20.0.00 107 mandatory spares.pressure switch, xmlbs04b2s11.74.631.52.0.00 108 mandatory spares.hose pipe.72.115.24.0.00 109 mandatory spares.hose clip ( 30 mm ) for 48.019.02.0.00, 40.149.02.0.00.50.519.06.000. 110 mandatory spares.rubber compensating sleeve.74.378.45.0.00 111 mandatory spares.locking plate.79.426.51.0.00 112 mandatory spares.locking plate.79.426.50.0.00 113 mandatory spares.locking plate.79.426.52.0.00 114 mandatory spares.sleeve spring.74.279.03.0.00 115 mandatory spares.ball bearing.74.050.05.0.00 116 mandatory spares.ball bearing.79.068.11.0.00 117 mandatory spares.ball bearing.79.050.12.0.00 118 mandatory spares.ball bearing.74.050.07.0.00 119 mandatory spares.serrated bush.74.050.62.0.00 120 mandatory spares.roller bearing.79.016.07.0.00 121 mandatory spares.cylindrical roller bearing.74.254.12.0.00 122 mandatory spares.circlip external 19 mm.50.501.19.000. 123 mandatory spares.internal circlip.74.254.16.0.00 124 mandatory spares.circlip external 65 mm.50.501.65.000. 125 mandatory spares.gasket.74.372.06.0.00 126 mandatory spares.copper washer ( 27x34 ) .50.508.31.000. 127 mandatory spares.shim.79.001.12.0.00 128 mandatory spares.gasket.79.095.02.0.00 129 mandatory spares.o ring.79.046.29.0.00 130 mandatory spares.o ring.74.260.23.0.00 131 mandatory spares.feed valve.79.046.09.0.00 132 mandatory spares.barrel cap.79.046.08.0.00 133 mandatory spares.antisplash piece.79.046.24.0.00 134 mandatory spares.copper washer ( 16x22 ) .50.508.14.000. 135 mandatory spares.copper washer ( 10x14 ) .50.508.07.000. 136 mandatory spares.o ring.79.060.15.0.00 137 mandatory spares.fuel pump filter.79.046.25.0.00 138 mandatory spares.locking wire.74.254.28.0.00 139 mandatory spares.banjo bolt.79.093.04.0.00 140 mandatory spares.feed valve spring.79.046.10.0.00 141 mandatory spares.o ring 15 x 204.74.531.38.0.00 142 mandatory spares.o ring 5 x 589.74.531.39.0.00 143 mandatory spares.o ring 5 x 260 ( 20313 ) .74.531.40.0.00 144 mandatory spares.o ring.27.065.04.0.00 145 mandatory spares.o ring.79.068.20.0.00 146 mandatory spares.o ring.71.067.33.0.00 147 mandatory spares.spacer.75.295.36.0.00 148 mandatory spares.bronze shim.75.295.37.0.00 149 mandatory spares.spherical bearing assly. for tacoma opv s.74.531.78.0.00 150 mandatory spares.silastic black.75.345.18.0.00 151 mandatory spares.large end bearing pair.74.369.10.0.00 152 mandatory spares.expansion bellow.74.405.01.0.00 153 mandatory spares.expansion bellow.79.079.25.0.00 154 mandatory spares.cyclam seal assly.75.068.90.0.00 155 mandatory spares.mechanical seal for ffp.74.326.46.0.00 156 mandatory spares.o ring for ffp.74.326.34.0.00 157 mandatory spares.o ring fuel feed pump.74.326.35.0.00 158 mandatory spares.bearing bush for fuel feed pump.74.269.63.0.00 159 mandatory spares.set of gaskets for hyd. motor ( mh 114a ) .27.039.42.0.00 160 mandatory spares.set of full flow elements for lo filter.74.386.75.0.00 161 mandatory spares.set of diversion element for lo filter.74.386.76.0.00 162 mandatory spares.sealing ring.79.155.03.0.00 163 mandatory spares.main bearing assly.74.456.20.0.00 164 mandatory spares.brg.opp.side to timing gear.79.011.01.0.00 165 mandatory spares.bearing.74.011.03.0.00 166 mandatory spares.o ring for particle detecting filter.79.152.68.0.00 167 mandatory spares.o ring for particle detecting filter.79.152.74.0.00 168 mandatory spares.o ring for particle detecting filter.79.152.67.0.00 169 mandatory spares.element for l.o.thermostat ( 63 / 71deg c ) .74.385.11.0.00 170 mandatory spares.elastic mountings.74.364.01.0.00 171 mandatory spares.overspeed air solenoid valve ( 241 no, 24v ) .79.720.04.0.00 172 mandatory spares.valve with pneumatic control.74.501.02.0.00 173 mandatory spares.circulation heater element for ktmi opv.74.631.30.0.00 174 mandatory spares.thermostat for circulation heater for ktmi opv.74.631.31.0.00 175 mandatory spares.thermostat element for naval opv.74.631.24.0.00 176 mandatory spares.seal kit ( fresh water thermostatic valve for naval opv.74.631.25.0.00 177 mandatory spares.filter element.75.513.13.0.00 178 mandatory spares.special seal.75.513.14.0.00 179 mandatory spares.regu valve.75.509.10.0.00 180 mandatory spares.2 way pneumatic valve.74.510.10.0.00 181 mandatory spares.gasket for glacier filter gf600 11.72.152.13.0.00 182 mandatory spares.damper bush.74.279.05.0.00 183 mandatory spares.bearing shell.76.078.22.0.00 184 mandatory spares.barrel plunger assembly 23 dia grad.74.398.02.0.00 185 mandatory spares.bs ring.79.093.08.0.00 186 mandatory spares.spring pack.74.531.50.0.00 187 mandatory spares.link.75.295.35.0.00 188 mandatory spares.helicoflex sealing joint.27.067.16.0.00 189 mandatory spares.o ring.79.041.15.0.00 190 mandatory spares.injector gasket.79.041.18.0.00 191 mandatory spares.o ring.79.041.21.0.00 192 mandatory spares.b s ring.79.041.17.0.00 193 mandatory spares.bush viton.79.041.19.0.00 194 mandatory spares.injector nozzle assembly.27.067.05.0.00 195 mandatory spares.o ring for centrifugal filter.79.421.53.0.00 196 mandatory spares.o ring for centrifugal filter.79.421.54.0.00 197 mandatory spares.o ring for centrifugal filter.79.421.50.0.00 198 mandatory spares.copper washer ( 12x16 ) .50.508.09.000. 199 mandatory spares.starting air valve assly ( cyl.head ) .79.040.30.0.00 200 mandatory spares.o ring.79.040.10.0.00 201 mandatory spares.copper washer ( 30x38 ) .50.508.35.000. 202 mandatory spares.ring.79.040.06.0.00 203 mandatory spares.conical spring washer ( m14 ) .50.527.10.000. 204 mandatory spares.o ring.79.103.03.0.00 205 mandatory spares.bs ring.79.093.08.0.00 206 mandatory spares.oil seal.79.161.50.0.00 207 mandatory spares.o ring.79.161.51.0.00 208 mandatory spares.o ring.79.161.52.0.00 209 mandatory spares.o ring.79.046.28.0.00 210 mandatory spares.seal joint.79.168.10.0.00 211 mandatory spares.seal joint.79.168.11.0.00 212 mandatory spares.c0pper washer.79.038.05.0.00 213 mandatory spares.copper washer ( 20x26 ) .50.508.19.000. 214 mandatory spares.indicator cock assembly.79.238.50.0.00 215 mandatory spares.o ring.79.043.14.0.00 216 mandatory spares.loctite 242.79.001.34.0.00 217 mandatory spares.loctite 549.79.001.35.0.00 218 mandatory spares.bearing unit comp.79.665.01.0.00 219 mandatory spares.bearing unit.79.665.02.0.00 220 mandatory spares.sealing bush.79.665.04.0.00 221 mandatory spares.gauge glass.79.665.08.0.00 222 mandatory spares.gasket.79.665.09.0.00 223 mandatory spares.sealing bush.79.665.03.0.00 224 mandatory spares.safety ring.79.665.13.0.00 225 mandatory spares.piston ring.79.665.12.0.00 226 mandatory spares.ring nut.79.421.78.0.00 227 mandatory spares.o ring.79.001.09.0.00 228 mandatory spares.bush.79.001.11.0.00 229 mandatory spares.bush.79.001.08.0.00 230 mandatory spares.self locking nyloc nut m12.50.037.12.000. 231 mandatory spares.o ring for inspection door.74.357.15.0.00 232 mandatory spares.sealing joint.79.119.05.0.00 233 mandatory spares.sealing joint.79.119.05.0.00 234 mandatory spares.o ring.79.403.03.0.00 235 mandatory spares.addesive.75.345.08.0.00 236 mandatory spares.bolt.79.021.03.0.00 237 mandatory spares.bolt.79.021.04.0.00 238 mandatory spares.o ring.79.026.02.0.00 239 mandatory spares.hylomar paste.79.026.04.0.00 240 mandatory spares.piston ring top.80.192.25.0.00 241 mandatory spares.piston ring ( compression ) .80.192.05.0.00 242 mandatory spares.scrapper ring assembly.80.192.15.0.00 243 mandatory spares.o ring.79.022.10.0.00 244 mandatory spares.circlip i48.50.502.48.000. 245 mandatory spares.inlet valve.70.075.87.0.00 246 mandatory spares.valve seat insert inlet.79.029.03.0.00 247 mandatory spares.exhaust valve.27.099.43.0.00 248 mandatory spares.exhaust valve seat.79.029.06.0.00 249 mandatory spares.copper washer ( 60x68 ) .50.508.51.000. 250 mandatory spares.copper washer.79.029.04.0.00 251 mandatory spares.gasket for cyl. head.79.029.32.0.00 252 mandatory spares.valve guide.27.023.22.0.00 253 mandatory spares.ring.79.029.39.0.00 254 mandatory spares.o ring / sealing cord.74.466.02.0.00 255 mandatory spares.rocking arm assly.79.028.07.0.00 256 mandatory spares.safety valve on cyl.head.79.044.20.0.00 257 mandatory spares.spring dowel ( 3x12 ) .50.540.05.012. 258 mandatory spares.ball.50.529.21.000. 259 mandatory spares.metafram bush.79.048.08.0.00 260 mandatory spares.oil seal.79.048.10.0.00 261 mandatory spares.distributor disc tufftriding comp.79.048.05.0.00 262 mandatory spares.spring dowel pin.50.540.05.024. 263 mandatory spares.o ring.79.351.59.0.00 264 mandatory spares.o ring.79.351.60.0.00 265 mandatory spares.copper washer ( 18x24 ) .50.508.17.000. 266 mandatory spares.joint.74.078.09.0.00 267 mandatory spares.gasket for exh.79.078.04.0.00 268 mandatory spares.copaslip.27.005.56.0.00 269 mandatory spares.molykote.27.005.57.0.00 270 mandatory spares.inlet manifold seal.79.077.02.0.00 271 mandatory spares.o ring.79.087.06.0.00 272 mandatory spares.gasket.79.087.05.0.00 273 mandatory spares.joint.74.251.34.0.00 274 mandatory spares.copper washer ( 18x22 ) .50.508.16.000. 275 mandatory spares.joint.74.280.22.0.00 276 mandatory spares.flexmast connection.74.271.17.0.00 277 mandatory spares.joint.74.271.24.0.00 278 mandatory spares.oval joint.79.088.21.0.00 279 mandatory spares.joint.74.271.24.0.00 280 mandatory spares.gasket.79.148.04.0.00 281 mandatory spares.gasket.74.378.49.0.00 282 mandatory spares.flexmast coupling.74.144.06.0.00 283 mandatory spares.o ring.75.084.12.0.00 284 mandatory spares.sealing ring.75.068.11.0.00 285 mandatory spares.o ring.74.266.18.0.00 286 mandatory spares.o ring.74.266.20.0.00 287 mandatory spares.loctite 641.79.016.20.0.00 288 mandatory spares.o ring.74.266.19.0.00 289 mandatory spares.roller cyl.brg..79.068.12.0.00...

Indian Navy - Andhra Pradesh

26673642 6000 hourly routines and camshaft replacement on bmes in ship , bme . clean and check all injectors . 6pa6l 280 semt . , bme . inspect crank case through upper and lower doors . 6pa6l 280 semt . , bme . examine cams and rollers6pa6l 280 semt . , bme . drain and top up governor . 6pa6l 280 semt . , bme . check engine foundation bolts and anchor bolts tightening torque6pa6l 280 semt . , bme . check fuel rack movement6pa6l 280 semt . , bme . check over speed trip at no load . run the electronic overspeed test ( over speed safety slide valve to be overhauled ) 6pa6l 280 semt . , bme . measure crankshaft deflections6pa6l 280 semt . , bme . check replace sealing filters of injection pumps6pa6l 280 semt . , bme . carry out tappet setting6pa6l 280 semt . , bme . two pistons , connecting rod assemblies , cylinder heads and con rod bearings to be examined per engine6pa6l 280 semt . , bme . visual examination of timing gear train teeth6pa6l 280 semt . , bme . inspection & examination of turbocharger and cleaning of the compressor & turbine casing insitu ( koel note: replacement of bearings , repair to water casing , rotor balancing , removal , & refitment is not covered in this scope . if required will be charges6pa6l 280 semt . , bme . inspection of starting air disc and starting air valve6pa6l 280 semt . , bme . removal & refitment of air inter cooler6pa6l 280 semt . , bme . chemicle claeaning of cac6pa6l 280 semt . , bme . fuel booster pump drive and governor drive bearings , serrated bush replacement6pa6l 280 semt . , bme . fuel booster pump overhauling6pa6l 280 semt . , bme . visual inspection of valkun coupling6pa6l 280 semt . , bme . inspection of spring packs of vibration damper by extraction from slots one at a time6pa6l 280 semt . , bme . replacement of both main engines camshafts . 6pa6l 280 semt . , mandatory spares . bush . 79 . 001 . 08 . 0 . 00 , mandatory spares . o ring . 79 . 001 . 09 . 0 . 00 , mandatory spares . bush . 79 . 001 . 11 . 0 . 00 , mandatory spares . o ring / sealing cord . 74 . 466 . 02 . 0 . 00 , mandatory spares . gasket for cyl . head . 79 . 029 . 32 . 0 . 00 , mandatory spares . copper washer ( 12x18 ) . 50 . 508 . 10 . 000 . , mandatory spares . c0pper washer . 79 . 038 . 05 . 0 . 00 , mandatory spares . o ring . 79 . 152 . 50 . 0 . 00 , mandatory spares . o ring . 79 . 152 . 94 . 0 . 00 , mandatory spares . paper insert . 79 . 152 . 53 . 0 . 00 , mandatory spares . o ring . 79 . 040 . 10 . 0 . 00 , mandatory spares . copper washer ( 30x38 ) . 50 . 508 . 35 . 000 . , mandatory spares . o ring . 79 . 161 . 52 . 0 . 00 , mandatory spares . copper washer ( 12x18 ) . 50 . 508 . 10 . 000 . , mandatory spares . ring . 72 . 040 . 10 . 0 . 00 , mandatory spares . c0pper washer . 79 . 038 . 05 . 0 . 00 , mandatory spares . o ring . 79 . 043 . 14 . 0 . 00 , mandatory spares . copper washer ( 20x26 ) . 50 . 508 . 19 . 000 . , mandatory spares . ring . 79 . 040 . 06 . 0 . 00 , mandatory spares . b s ring . 79 . 041 . 17 . 0 . 00 , mandatory spares . o ring . 79 . 041 . 21 . 0 . 00 , mandatory spares . o ring . 79 . 041 . 15 . 0 . 00 , mandatory spares . bush viton . 79 . 041 . 19 . 0 . 00 , mandatory spares . injector gasket . 79 . 041 . 18 . 0 . 00 , mandatory spares . helicoflex sealing joint . 27 . 067 . 16 . 0 . 00 , mandatory spares . injector nozzle assembly . 27 . 067 . 05 . 0 . 00 , mandatory spares . fuel pump filter . 79 . 046 . 25 . 0 . 00 , mandatory spares . copper washer ( 12x18 ) . 50 . 508 . 10 . 000 . , mandatory spares . inlet manifold seal . 79 . 077 . 02 . 0 . 00 , mandatory spares . gasket for exh . 79 . 078 . 04 . 0 . 00 , mandatory spares . gasket sq . . 81 . 081 . 03 . 0 . 00 , mandatory spares . gasket . 79 . 087 . 05 . 0 . 00 , mandatory spares . o ring . 79 . 087 . 06 . 0 . 00 , mandatory spares . gasket . 81 . 177 . 05 . 0 . 00 , mandatory spares . gasket . 81 . 177 . 06 . 0 . 00 , mandatory spares . gasket . 81 . 177 . 07 . 0 . 00 , mandatory spares . o ring for inspection door . 74 . 357 . 15 . 0 . 00 , mandatory spares . oil seal . 79 . 161 . 50 . 0 . 00 , mandatory spares . o ring . 79 . 161 . 51 . 0 . 00 , mandatory spares . o ring . 79 . 161 . 52 . 0 . 00 , mandatory spares . o ring . 79 . 046 . 28 . 0 . 00 , mandatory spares . loctite 242 . 79 . 001 . 34 . 0 . 00 , mandatory spares . loctite 549 . 79 . 001 . 35 . 0 . 00 , mandatory spares . loctite . 74 . 588 . 03 . 0 . 00 , mandatory spares . prc glue . 79 . 034 . 76 . 0 . 00 , mandatory spares . copaslip . 27 . 005 . 56 . 0 . 00 , mandatory spares . molykote . 27 . 005 . 57 . 0 . 00 , mandatory spares . brg . complete compressor end . 81 . 665 . 02 . 0 . 00 , mandatory spares . brg . complete , turbine end . 81 . 665 . 03 . 0 . 00 , mandatory spares . sealing bush . 81 . 665 . 07 . 0 . 00 , mandatory spares . sealing bush . 81 . 665 . 08 . 0 . 00 , mandatory spares . gauge glass 583 . 81 . 665 . 05 . 0 . 00 , mandatory spares . insert bush . 81 . 665 . 10 . 0 . 00 , mandatory spares . piston ring for t/c . 81 . 665 . 43 . 0 . 00 , mandatory spares . safety ring for t/c . 81 . 665 . 52 . 0 . 00 , mandatory spares . gasket . 79 . 148 . 04 . 0 . 00 , mandatory spares . o ring / sealing cord . 79 . 036 . 26 . 0 . 00 , mandatory spares . gasket . 70 . 054 . 15 . 0 . 00 , mandatory spares . gasket . 70 . 054 . 16 . 0 . 00 , mandatory spares . copper washer ( 18x24 ) . 50 . 508 . 17 . 000 . , mandatory spares . ball bearing . 79 . 049 . 11 . 0 . 00 , mandatory spares . ball bearing . 79 . 049 . 13 . 0 . 00 , mandatory spares . o ring . 79 . 049 . 24 . 0 . 00 , mandatory spares . set of oil seal for fuel booster pump . 79 . 426 . 56 . 0 . 00 , mandatory spares . ball bearing . 79 . 350 . 15 . 0 . 00 , mandatory spares . needle roller bearing . 79 . 350 . 19 . 0 . 00 , mandatory spares . washer . 79 . 350 . 31 . 0 . 00 , mandatory spares . o ring . 81 . 700 . 06 . 0 . 00 , mandatory spares . o ring . 81 . 700 . 07 . 0 . 00 , mandatory spares . o ring . 81 . 700 . 08 . 0 . 00 , mandatory spares . con rod brg ( pair ) . 74 . 369 . 10 . 0 . 00 , mandatory spares . piston ring top . 79 . 023 . 01 . 0 . 00 , mandatory spares . piston ring ( compression ) . 79 . 024 . 01 . 0 . 00 , mandatory spares . scrapper ring assembly . 80 . 192 . 15 . 0 . 00 , mandatory spares . exhaust valve . 27 . 099 . 43 . 0 . 00 , mandatory spares . inlet valve . 70 . 075 . 87 . 0 . 00 , mandatory spares . valve guide . 27 . 023 . 22 . 0 . 00 , mandatory spares . o ring exh . valve guide . 27 . 023 . 25 . 0 . 00 , mandatory spares . screw with expanded tappet . 79 . 033 . 28 . 0 . 00 , mandatory spares . outside spring . 79 . 031 . 09 . 0 . 00 , mandatory spares . spring . 79 . 031 . 08 . 0 . 00 , mandatory spares . split collar ( pair ) . 79 . 031 . 86 . 0 . 00 , mandatory spares . indicator cock assembly . 79 . 238 . 50 . 0 . 00 , mandatory spares . exhaust valve seat . 79 . 029 . 06 . 0 . 00 , mandatory spares . valve seat insert inlet . 79 . 029 . 03 . 0 . 00 , mandatory spares . connection . 79 . 042 . 22 . 0 . 00 , mandatory spares . injector tappet . 79 . 041 . 04 . 0 . 00 , mandatory spares . spring . 79 . 041 . 05 . 0 . 00 , mandatory spares . sheathed injection pipe . 79 . 101 . 01 . 0 . 00 , mandatory spares . clamping collar . 79 . 079 . 49 . 0 . 00 , mandatory spares . driven rotor . 79 . 350 . 23 . 0 . 00 , mandatory spares . drive rotor for fuel feed pump . 79 . 350 . 11 . 0 . 00 , mandatory spares . ring . 79 . 040 . 06 . 0 . 00 , mandatory spares . conical spring washer ( m14 ) . 50 . 527 . 10 . 000 . , mandatory spares . assembly valve gear . 79 . 028 . 20 . 0 . 00 , mandatory spares . screw with dog point . 79 . 028 . 06 . 0 . 00 , mandatory spares . loctite 242 . 79 . 001 . 34 . 0 . 00 , mandatory spares . loctite 549 . 79 . 001 . 35 . 0 . 00 , mandatory spares . camshaft section for cyl 1 2 3 . 81 . 017 . 01 . 0 . 00 , mandatory spares . camshaft section for cyl 4 5 6 . 81 . 017 . 02 . 0 ...

Indian Navy - Andhra Pradesh

26432893 tender for otr for undertaking 12 k routines on ins kamorta g3 da , services , fuel system: ( a ) clean and calibrate injectors and record test pressure in service log . also change injector inlet screen , ( b ) replace rocker cover gaskets . ( c ) adjust valve tappet clearances within limits and record in service log . ( d ) replace fuel pump filter ( screen and magnet ) . ( e ) calibrate pt pump and record in service log . , air system: ( a ) clean turbocharger , compressor wheel and diffuser . ( b ) check turbo charger radial / end bearing clearance insitu . ( c ) renew o ring and teflon gasket when turbocharger is opened for checking clearances . ( d ) torque manifold nuts or cap screws as per specifications . , charge air cooler & fresh water cooler: ( a ) clean the internal passages of charge air cooler and fresh water cooler coolant side using restore plus as laid down in operating manual . pressure testing to be undertaken . ( b ) renew coolant in the system . ( c ) remove and chemically clean fresh water cooler . renew gasket and o rings . pressure testing to be undertaken , vibration damper: ( a ) check thickness of vibration damper at 0 . 90 , 180 and 270 degree positions . ( b ) replace damper if variation of the 4 readings exceeds 0 . 010 inch ( 0 . 25mm ) or exceeds max allowable thickness . checks to be undertaken in coupled condition . , check crank end clearances with a dial indicator , attaching against damper min 0 . 13 mm , max 0 . 51 mm . , carry out visual inspection of sv mounts and torque tighting , torque tightening: check torque tightening of coupling inner / outer members as specified in the manual for das fitted with holset or centamax couplings . in case of vulcan couplings , check for cracks on rubber and if wear mark does not exceed limits . check tightness of adapt plate bolts . alignment : undertake alignment checks between the generator and engine . , checking and trails ( for all engines ) cold checks , hot checks and trails , random inspection of two representative liners and bearings of the engines ( a ) remove all cylinder heads for decarbonisation , pressure testing and vacuum testing . ( b ) gauging and inspection of liner from each bank for corrosion / pitting post extraction . ( c ) gauging of connecting rod big end bearing / small end bushes clearances and examination of big end shell for the cylinders opened . ( d ) checking condition of valve gear bracket , transfer sleeve saelings ring and injector tube . inspection of valve gear parts and valve seat inserts of the cylinder head opened ( e ) examine crank pin surfaces and check for ovality and wear . ( f ) examine of pistons for wear and gauge piston ring clearances . , anticipatory scope of work ( a ) inspection of balance liners and bearings based on inspection report of the two sample liners . replacement of cylinder liners . ( b ) renew rings based on piston rings clearances during gauging . ( c ) replacement of pistons ( per pistons ) in case wear / corrosion is observed beyond permissiable limits . , overhauling of lub oil filter bed , spares , kit , piston , set , piston ring , screw , connecting rod cap , guide valve stem , tappet , hyd var timing , retainer , screen , spring , injector , ball , check , pin , roll , plug , nut , lock , retainer , injector spring , gasket , turbocharger , hose , flexible , seal , o ring , bearing , ball , shaft , tachometer drive , gear , tachometer drive , seal , o ring , seal , o ring , barrel & plunger , kit , seal , seal , o ring , seal , rectangular strip , seal , dust , filler , cap , seal , o ring , seal , o ring , seal , o ring , gasket , lub oil clr cover , plug , zinc electrode , seal , lta fitting o ring , anticipatory spares , shield , turbocharger heat , impeller , tur compressor...

Indian Navy - Andhra Pradesh

25112131 one time repair for undertaking 12000 hourly routines on k da of ins kadmatt , services , fuel system: ( a ) clean and calibrate injectors and also change injector inlet screen . ( b ) replace rocker cover gaskets . ( c ) adjust valve tappet clearances within limits . ( d ) replace fuel pump filter ( screen and magnet ) . ( e ) calibrate pt fuel pump . , air system: ( a ) clean turbocharger , compressor wheel and diffuser . ( b ) check turbo charger radial/end bearing clearance insitu . ( c ) torque tightening of manifold nuts or cap screws as per specifications . , charge air cooler & fresh water cooler: ( a ) clean the internal passages of charge air cooler and fresh water cooler coolant side using restore plus as laid down in operating manual . ( b ) renew coolant in the system . ( c ) inspect charge air cooler air side and if required clean using hot water and pressure test up to 2kg/cm2 . , vibration damper: ( a ) check thickness of vibration damper at 0 . 90 , 180 and 270 degree positions . ( b ) replace damper if variation of the 4 readings exceeds 0 . 010 inch ( 0 . 25mm ) or exceeds max allowable thickness . , carryout the visual inspection of sv mounts . renew if their condition is deteriorated . , check crank end clearances with a dial indicator , attaching against damper min 0 . 13 mm , max 0 . 51 mm . , torque tightening: check torque tightening of coupling inner/outer members as specified in the manual for das fitted with holset or centamax couplings . in case of vulcan couplings , check for cracks on rubber and if wear mark does not exceed limits . check tightness of adaptor plate bolts . , alignment checks: undertake alignment checks between the generator and engine and restore radial/axial initial alignment to 25% of the max limit . , dttt and etmu trails , dismantling the engine into components for overhaul and visual inspection ( a ) remove all cylinder heads for de carbonisation . ( b ) removal of pistons and connecting rods . ( c ) removal cylinder liners for renewal . ( d ) gauging as required , mandatory spares , kit , upper engine gasket , kit , liner , kit , piston , set , piston ring , screw , connecting rod cap , washer , plain , thermostat , seal , thermostat , valve exhaust , guide valve stem , spring valve , insert , valve seat , insert valve seat , collet valve , plug , expansion , plug , expansion , retainer , valve spring , pin , groove , tappet , hyd var timing , kit inj barrel & plunger , cup injector , seal , o ring , spring , injector , ball , check , pin , roll , screen , filter , gasket , injector , spring , injector , plug , nut , lock , link , injector plunger , retainer , injector spring , tappet , hyd var timing , cap , tappet top stop , nut , tappet top stop lock , nut , lock , clamp , injector , kit , turbo repair hc5a , screw , hex flange head cap , gasket , turbocharger , gasket , connection , gasket , connection , hose , flexible , hose , flexible , seal , o ring , gasket governor set , bearing , ball , shield , shutoff valve , screen , filter , shaft , throttle , shaft , fuel pump drive , valve , check , shaft , tachometer drive , gear , tachometer drive , screw , hexagon head cap , pump , gear fuel , actuator , etr fuel control , seal , o ring , seal , o ring , valve , shutoff , seal , o ring , cap , fuel pump filter , barrel & plunger , core , aftercooler , seal , rectangular strip , seal , dust , hose , flexible , seal , o ring , gasket , lub oil clr cover , nut , lock , filler , cap , seal , o ring , seal , o ring , seal , o ring , cover , o ring seal , seal , tank o ring , seal , lta fitting o ring , element , lub oil filter , inhibitor , corrosion , radiwash_3ltr , indicator , restriction , shield , turbocharger heat , impeller , tur compressor , diffuser , turbocharger , slinger , oil , rod , push , cover , fuel pump front , cover , o ring seal , seal , tank o ring , seal , o ring , plug , zinc electrode , cover , tank assembly , in out , tank assembly , glass , sight , damper , vibration , damper , vibration , anticipatory spares , exchanger , heat , set , lower engine gasket , bearing , connecting rod , valve intake , rotator , valve , retainer , screen , seal , injector , link , injector plunger , nut , lock , knob , seal , o ring , key , square , cap , fuel pump filter , kit , seal , screen , filter , seal , rectangular ring , seal , aftercooler core , seal , o ring , seal , grommet , core , cooler , pump , water , zinc , plug , seal , o ring , element air cleaner , element air cleaner , shaft & wheel , rod , push , seal , lta fitting o ring...

Indian Navy - Andhra Pradesh

25057908 tender enquiry for 24k routines on bmes in ship 1 bme.carry out following as part of 24000 hrly routine (major ovehaul) on both main engine.16pa6v 280 2 bme.dismantle complete engine and check crank shaft wear. grind the crank pins and journals. note: job will be done as : check and measure diamensions of crankpins and journals of crank shaft. carry out cam wears measurement on cranpins..16pa6v 280 3 bme.replace crack shaft bearing shells and thrust collars.16pa6v 280 4 bme.check cam shaft shaft journals and cam. examine cam shaft bearing bushes. renew if necessary. renew cam followers and push rods.16pa6v 280 5 bme.carryout complete cleaning and inspection of crank case, internally and externally, with crank shaft in place. note: dp test on crankcase (at 4 points only) 1. liner bore, 2. all gears of gear train (except water pump gear),.16pa6v 280 6 bme.change all full flow and diversion element of lub oil filter hydraulic motor.16pa6v 280 7 bme.renew big end bearing and small end bearing and gudgeon pins.16pa6v 280 8 bme.descale all cylinder liners and renew sealing rings. examine upper flange. note: (no rehoning of liners consided).16pa6v 280 9 bme.renew idle pinion roller bearings of timing gear train..16pa6v 280 10 bme.inspect vibration damper. renew bushes and springs..16pa6v 280 11 bme.overhaul and carry out timing, phasing and calibration of fuel injection pump.16pa6v 280 12 bme.overhaul lub oil pump. reset safety valve..16pa6v 280 13 bme.overhaul fresh water and sea water pumps. renew bearing and seals. inspect drive pinion. replace unit if necessary.16pa6v 280 14 bme.replace all springs of gieslinger coupling and friction bush.16pa6v 280 15 bme.overhaul turning gear mechanism.16pa6v 280 16 bme.clean glacier centrifuge purifier and “moatti” filter.16pa6v 280 17 bme.test the injectors for spray, seat tightness and automisation and carry out calibration.16pa6v 280 18 bme.check and reset tappet clearance under cold condition.16pa6v 280 19 bme.measure and record crank shaft deflection.16pa6v 280 20 bme.overhaul fuel booster pump. replace serrated bush of pump drive. renew all seals and joints.16pa6v 280 21 bme.inspect piston and connecting rod for serviceabilty. renew as necessary. replace all piston rings and measure clearances inside their grooves.16pa6v 280 22 bme.overhaul complete turbo charger unit, renew bearings, sealing rings and bushes..16pa6v 280 23 bme.(aj) overhaul the air distributor disc and air starting valves. renew air starting valves.16pa6v 280 24 bme.(ak) overhaul over speed trip slide valve and replace seals..16pa6v 280 25 bme.(al) overhaul cylinder heads, decorbonise, descale coolant passage. replace cylinder head gaket. check for serviceability replace if necessary. renew rocker arm bushes and tappets. replace inlet and exhaust valves. renew valve bridges. recondition the e.16pa6v 280 26 bme.check valves and rings of air stating valve. renew if necessary.16pa6v 280 27 bme.check for zero error of fuel rack on engine and correct as required.16pa6v 280 28 bme.renew seal of fuel linkage rods. check link rods for bending and adjust dead rack position.16pa6v 280 29 bme.inspect / overhaul speed governor and carry out bench test.16pa6v 280 30 bme.removal & fitment of governor assly.16pa6v 280 31 bme.overhaling & calibaration of governor assly carry out bench test. note: governor transportation / packing to be arranged by yard / ss).16pa6v 280 32 bme.check teething and serration clearance and backlash of governor drive.16pa6v 280 33 bme.renew sv mounts. note: the job involves renewal of mount and carrying out engine alignment with respect to gear box. work on girder, machine, chock supply, welding, cutting, system piping removal / refitment, in yard scope).16pa6v 280 34 bme.chemically clean and pressure test lub oil coolers. rectify the defects if any..16pa6v 280 35 bme.replace rings of expansion joints of exhaust manifold of main engine to clean & realign.16pa6v 280 36 bme.chemically clean charge air cooler fresh water side and air space side, pressure test for leaks repair defects..16pa6v 280 37 bme.renew all rubber hoses bellow 250 mm 02 nos . change all flexible hoses.16pa6v 280 38 bme.dismantle and clean the thermostat valve replace as necessary.16pa6v 280 39 bme.chemical cleaning and pressure test of fresh water cooler rectify the defects if any. job to be done as follow.16pa6v 280 40 bme.replace two way pneumatic valve of fuel circuit..16pa6v 280 41 bme.check over speed trip at no load. (gestra valve to be overhauled)..16pa6v 280 42 mandatory spares.roller bearing.74.266.16.0.00 43 mandatory spares.o ring.79.068.20.0.00 44 mandatory spares.punched joint.74.105.12.0.00 45 mandatory spares.punched gasket.74.105.18.0.00 46 mandatory spares.joint.74.105.23.0.00 47 mandatory spares.joint for balmo fuel feed pump.74.421.02.0.00 48 mandatory spares.bush for fuel booster pump.74.326.41.0.00 49 mandatory spares.hose pipe.72.115.24.0.00 50 mandatory spares.hose clip (30 mm) for 48.019.02.0.00, 40.149.02.0.00.50.519.06.000. 51 mandatory spares.flex.hose.74.381.02.0.00 52 mandatory spares.rubber compensating sleeve.74.381.64.0.00 53 mandatory spares.rubber compensating sleeve.74.381.68.0.00 54 mandatory spares.rubber compensating sleeve.74.381.70.0.00 55 mandatory spares.breather o/l conn. bank a/b.74.381.98.0.00 56 mandatory spares.rubber compensating sleeve.74.381.72.0.00 57 mandatory spares.rubber compensating sleeve.75.267.23.0.00 58 mandatory spares.rubber compensating sleeve.74.381.77.0.00 59 mandatory spares.flex hose.74.381.21.0.00 60 mandatory spares.rubber compensating sleeve.74.381.81.0.00 61 mandatory spares.rubber compensating sleeve.74.381.82.0.00 62 mandatory spares.flex hose.74.381.26.0.00 63 mandatory spares.flex hose.74.381.29.0.00 64 mandatory spares.flex hose.74.381.33.0.00 65 mandatory spares.flexible hose.74.381.34.0.00 66 mandatory spares.flexible hose.74.381.39.0.00 67 mandatory spares.flexible hose.74.381.45.0.00 68 mandatory spares.flex hose.74.381.36.0.00 69 mandatory spares.set of gaskets for lub oil filter housing.74.386.78.0.00 70 mandatory spares.o ring.79.160.07.0.00 71 mandatory spares.ball bearing for lub oil filter.74.386.67.0.00 72 mandatory spares.ball bearing for hyd. motor.74.306.83.0.00 73 mandatory spares.bearing bushes.79.053.19.0.00 74 mandatory spares.uniball joint female socket type.79.056.18.0.00 75 mandatory spares.oval gasket.74.263.02.0.00 76 mandatory spares.stop ring.79.053.17.0.00 77 mandatory spares.coupling ring.79.053.18.0.00 78 mandatory spares.bearing bush.74.262.06.0.00 79 mandatory spares.bearing bush.74.262.07.0.00 80 mandatory spares.simrit ring.74.262.08.0.00 81 mandatory spares.copper washer (18x24).50.508.17.000. 82 mandatory spares.o ring.74.265.05.0.00 83 mandatory spares.joint.74.265.06.0.00 84 mandatory spares.gasket.74.356.34.0.00 85 mandatory spares.o ring.79.160.07.0.00 86 mandatory spares.o ring.74.402.21.0.00 87 mandatory spares.o ring.74.402.11.0.00 88 mandatory spares.o ring.74.402.10.0.00 89 mandatory spares.reinforced thrust bearing.74.007.04.0.00 90 mandatory spares.o ring.79.101.03.0.00 91 mandatory spares.o ring.79.101.04.0.00 92 mandatory spares.copper washer (12x18).50.508.10.000. 93 mandatory spares.gasket.74.352.21.0.00 94 mandatory spares.o ring.74.065.17.0.00 95 mandatory spares.joint.74.159.13.0.00 96 mandatory spares.joint.74.159.12.0.00 97 mandatory spares.o ring.79.149.13.0.00 98 mandatory spares.o ring.79.160.07.0.00 99 mandatory spares.gasket.74.389.14.0.00 100 mandatory spares.copper washer (30x38).50.508.35.000. 101 mandatory spares.joint.75.312.08.0.00 102 mandatory spares.copper washer (14x18).50.508.11.000. 103 mandatory spares.o ring.79.046.28.0.00 104 mandatory spares.o ring.71.067.33.0.00 105 mandatory spares.o ring.74.411.06.0.00 106 mandatory spares.o ring.79.068.20.0.00 107 mandatory spares.pressure switch, xmlbs04b2s11.74.631.52.0.00 108 mandatory spares.hose pipe.72.115.24.0.00 109 mandatory spares.hose clip (30 mm) for 48.019.02.0.00, 40.149.02.0.00.50.519.06.000. 110 mandatory spares.rubber compensating sleeve.74.378.45.0.00 111 mandatory spares.locking plate.79.426.51.0.00 112 mandatory spares.locking plate.79.426.50.0.00 113 mandatory spares.locking plate.79.426.52.0.00 114 mandatory spares.sleeve spring.74.279.03.0.00 115 mandatory spares.ball bearing.74.050.05.0.00 116 mandatory spares.ball bearing.79.068.11.0.00 117 mandatory spares.ball bearing.79.050.12.0.00 118 mandatory spares.ball bearing.74.050.07.0.00 119 mandatory spares.serrated bush.74.050.62.0.00 120 mandatory spares.roller bearing.79.016.07.0.00 121 mandatory spares.cylindrical roller bearing.74.254.12.0.00 122 mandatory spares.circlip external 19 mm.50.501.19.000. 123 mandatory spares.internal circlip.74.254.16.0.00 124 mandatory spares.circlip external 65 mm.50.501.65.000. 125 mandatory spares.gasket.74.372.06.0.00 126 mandatory spares.copper washer (27x34).50.508.31.000. 127 mandatory spares.shim.79.001.12.0.00 128 mandatory spares.gasket.79.095.02.0.00 129 mandatory spares.o ring.79.046.29.0.00 130 mandatory spares.o ring.74.260.23.0.00 131 mandatory spares.feed valve.79.046.09.0.00 132 mandatory spares.barrel cap.79.046.08.0.00 133 mandatory spares.antisplash piece.79.046.24.0.00 134 mandatory spares.copper washer (16x22).50.508.14.000. 135 mandatory spares.copper washer (10x14).50.508.07.000. 136 mandatory spares.o ring.79.060.15.0.00 137 mandatory spares.fuel pump filter.79.046.25.0.00 138 mandatory spares.locking wire.74.254.28.0.00 139 mandatory spares.banjo bolt.79.093.04.0.00 140 mandatory spares.feed valve spring.79.046.10.0.00 141 mandatory spares.o ring 15 x 204.74.531.38.0.00 142 mandatory spares.o ring 5 x 589.74.531.39.0.00 143 mandatory spares.o ring 5 x 260 (20313).74.531.40.0.00 144 mandatory spares.o ring.27.065.04.0.00 145 mandatory spares.o ring.79.068.20.0.00 146 mandatory spares.o ring.71.067.33.0.00 147 mandatory spares.spacer.75.295.36.0.00 148 mandatory spares.bronze shim.75.295.37.0.00 149 mandatory spares.spherical bearing assly. for tacoma opv s.74.531.78.0.00 150 mandatory spares.silastic black.75.345.18.0.00 151 mandatory spares.large end bearing pair.74.369.10.0.00 152 mandatory spares.expansion bellow.74.405.01.0.00 153 mandatory spares.expansion bellow.79.079.25.0.00 154 mandatory spares.cyclam seal assly.75.068.90.0.00 155 mandatory spares.mechanical seal for ffp.74.326.46.0.00 156 mandatory spares.o ring for ffp.74.326.34.0.00 157 mandatory spares.o ring fuel feed pump.74.326.35.0.00 158 mandatory spares.bearing bush for fuel feed pump.74.269.63.0.00 159 mandatory spares.set of gaskets for hyd. motor (mh 114a).27.039.42.0.00 160 mandatory spares.set of full flow elements for lo filter.74.386.75.0.00 161 mandatory spares.set of diversion element for lo filter.74.386.76.0.00 162 mandatory spares.sealing ring.79.155.03.0.00 163 mandatory spares.main bearing assly.74.456.20.0.00 164 mandatory spares.brg.opp.side to timing gear.79.011.01.0.00 165 mandatory spares.bearing.74.011.03.0.00 166 mandatory spares.o ring for particle detecting filter.79.152.68.0.00 167 mandatory spares.o ring for particle detecting filter.79.152.74.0.00 168 mandatory spares.o ring for particle detecting filter.79.152.67.0.00 169 mandatory spares.element for l.o.thermostat (63/71deg c).74.385.11.0.00 170 mandatory spares.elastic mountings.74.364.01.0.00 171 mandatory spares.overspeed air solenoid valve (241 no,24v).79.720.04.0.00 172 mandatory spares.valve with pneumatic control.74.501.02.0.00 173 mandatory spares.circulation heater element for ktmi opv.74.631.30.0.00 174 mandatory spares.thermostat for circulation heater for ktmi opv.74.631.31.0.00 175 mandatory spares.thermostat element for naval opv.74.631.24.0.00 176 mandatory spares.seal kit (fresh water thermostatic valve for naval opv.74.631.25.0.00 177 mandatory spares.filter element.75.513.13.0.00 178 mandatory spares.special seal.75.513.14.0.00 179 mandatory spares.regu valve.75.509.10.0.00 180 mandatory spares.2 way pneumatic valve.74.510.10.0.00 181 mandatory spares.gasket for glacier filter gf600 11.72.152.13.0.00 182 mandatory spares.damper bush.74.279.05.0.00 183 mandatory spares.bearing shell.76.078.22.0.00 184 mandatory spares.barrel plunger assembly 23 dia grad.74.398.02.0.00 185 mandatory spares.bs ring.79.093.08.0.00 186 mandatory spares.spring pack.74.531.50.0.00 187 mandatory spares.link.75.295.35.0.00 188 mandatory spares.helicoflex sealing joint.27.067.16.0.00 189 mandatory spares.o ring.79.041.15.0.00 190 mandatory spares.injector gasket.79.041.18.0.00 191 mandatory spares.o ring.79.041.21.0.00 192 mandatory spares.b s ring.79.041.17.0.00 193 mandatory spares.bush viton.79.041.19.0.00 194 mandatory spares.injector nozzle assembly.27.067.05.0.00 195 mandatory spares.o ring for centrifugal filter.79.421.53.0.00 196 mandatory spares.o ring for centrifugal filter.79.421.54.0.00 197 mandatory spares.o ring for centrifugal filter.79.421.50.0.00 198 mandatory spares.copper washer (12x16).50.508.09.000. 199 mandatory spares.starting air valve assly (cyl.head).79.040.30.0.00 200 mandatory spares.o ring.79.040.10.0.00 201 mandatory spares.copper washer (30x38).50.508.35.000. 202 mandatory spares.ring.79.040.06.0.00 203 mandatory spares.conical spring washer (m14).50.527.10.000. 204 mandatory spares.o ring.79.103.03.0.00 205 mandatory spares.bs ring.79.093.08.0.00 206 mandatory spares.oil seal.79.161.50.0.00 207 mandatory spares.o ring.79.161.51.0.00 208 mandatory spares.o ring.79.161.52.0.00 209 mandatory spares.o ring.79.046.28.0.00 210 mandatory spares.seal joint.79.168.10.0.00 211 mandatory spares.seal joint.79.168.11.0.00 212 mandatory spares.c0pper washer.79.038.05.0.00 213 mandatory spares.copper washer (20x26).50.508.19.000. 214 mandatory spares.indicator cock assembly.79.238.50.0.00 215 mandatory spares.o ring.79.043.14.0.00 216 mandatory spares.loctite 242.79.001.34.0.00 217 mandatory spares.loctite 549.79.001.35.0.00 218 mandatory spares.bearing unit comp.79.665.01.0.00 219 mandatory spares.bearing unit.79.665.02.0.00 220 mandatory spares.sealing bush.79.665.04.0.00 221 mandatory spares.gauge glass.79.665.08.0.00 222 mandatory spares.gasket.79.665.09.0.00 223 mandatory spares.sealing bush.79.665.03.0.00 224 mandatory spares.safety ring.79.665.13.0.00 225 mandatory spares.piston ring.79.665.12.0.00 226 mandatory spares.ring nut.79.421.78.0.00 227 mandatory spares.o ring.79.001.09.0.00 228 mandatory spares.bush.79.001.11.0.00 229 mandatory spares.bush.79.001.08.0.00 230 mandatory spares.self locking nyloc nut m12.50.037.12.000. 231 mandatory spares.o ring for inspection door.74.357.15.0.00 232 mandatory spares.sealing joint.79.119.05.0.00 233 mandatory spares.sealing joint.79.119.05.0.00 234 mandatory spares.o ring.79.403.03.0.00 235 mandatory spares.addesive.75.345.08.0.00 236 mandatory spares.bolt.79.021.03.0.00 237 mandatory spares.bolt.79.021.04.0.00 238 mandatory spares.o ring.79.026.02.0.00 239 mandatory spares.hylomar paste.79.026.04.0.00 240 mandatory spares.piston ring top.80.192.25.0.00 241 mandatory spares.piston ring (compression).80.192.05.0.00 242 mandatory spares.scrapper ring assembly.80.192.15.0.00 243 mandatory spares.o ring.79.022.10.0.00 244 mandatory spares.circlip i48.50.502.48.000. 245 mandatory spares.inlet valve.70.075.87.0.00 246 mandatory spares.valve seat insert inlet.79.029.03.0.00 247 mandatory spares.exhaust valve.27.099.43.0.00 248 mandatory spares.exhaust valve seat.79.029.06.0.00 249 mandatory spares.copper washer (60x68).50.508.51.000. 250 mandatory spares.copper washer.79.029.04.0.00 251 mandatory spares.gasket for cyl. head.79.029.32.0.00 252 mandatory spares.valve guide.27.023.22.0.00 253 mandatory spares.ring.79.029.39.0.00 254 mandatory spares.o ring / sealing cord.74.466.02.0.00 255 mandatory spares.rocking arm assly.79.028.07.0.00 256 mandatory spares.safety valve on cyl.head.79.044.20.0.00 257 mandatory spares.spring dowel (3x12).50.540.05.012. 258 mandatory spares.ball.50.529.21.000. 259 mandatory spares.metafram bush.79.048.08.0.00 260 mandatory spares.oil seal.79.048.10.0.00 261 mandatory spares.distributor disc tufftriding comp.79.048.05.0.00 262 mandatory spares.spring dowel pin.50.540.05.024. 263 mandatory spares.o ring.79.351.59.0.00 264 mandatory spares.o ring.79.351.60.0.00 265 mandatory spares.copper washer (18x24).50.508.17.000. 266 mandatory spares.joint.74.078.09.0.00 267 mandatory spares.gasket for exh.79.078.04.0.00 268 mandatory spares.copaslip.27.005.56.0.00 269 mandatory spares.molykote.27.005.57.0.00 270 mandatory spares.inlet manifold seal.79.077.02.0.00 271 mandatory spares.o ring.79.087.06.0.00 272 mandatory spares.gasket.79.087.05.0.00 273 mandatory spares.joint.74.251.34.0.00 274 mandatory spares.copper washer (18x22).50.508.16.000. 275 mandatory spares.joint.74.280.22.0.00 276 mandatory spares.flexmast connection.74.271.17.0.00 277 mandatory spares.joint.74.271.24.0.00 278 mandatory spares.oval joint.79.088.21.0.00 279 mandatory spares.joint.74.271.24.0.00 280 mandatory spares.gasket.79.148.04.0.00 281 mandatory spares.gasket.74.378.49.0.00 282 mandatory spares.flexmast coupling.74.144.06.0.00 283 mandatory spares.o ring.75.084.12.0.00 284 mandatory spares.sealing ring.75.068.11.0.00 285 mandatory spares.o ring.74.266.18.0.00 286 mandatory spares.o ring.74.266.20.0.00 287 mandatory spares.loctite 641.79.016.20.0.00 288 mandatory spares.o ring.74.266.19.0.00 289 mandatory spares.roller cyl.brg..79.068.12.0.00 ...

Indian Navy - Andhra Pradesh

24982963 tender enquiry for 24k routines on 02 das 6k routines 0n 01 da in ship , 24k . degutting of the connected pipe lines to facilitate the removal of the engine , lifting & shifting , shifting of engine . lowering and reinstallation charges for overhauled engine on foundation on board . renew all foundation bolts , fasteners and washers . connecting all degutted pipe lines of sea water pump , fresh water and fuel lines or in situ overhaul . nt 495 mg , 24k . dismantling all accessories , aux drives & check bearing clearances . check crankshaft dimension at main journal , crank pin , fillet area , check for any crack / bend . clean & flush out oil ways . renew big end bearings , their bolts , nuts and washers . check main bearing clearance . nt 495 mg , 24k . examine all liners for corrosion , scoring and wear limit . renew if requirednt 495 mg , 24k . clean and calibrate injectors and also change injector inlet screen . calibrate pt fuel pump , replace parts required . replace fip if required check . nt 495 mg , 24k . check engine block . clean all water passages and renew all sealing rings . examine gear teethes for any damages and worn out . replace if required . nt 495 mg , 24k . gauge all gudgeon pins , replace if required . examine and gauge all pistons for dimension , renew if necessary . renew all piston ringsnt 495 mg , 24k . overhaul hydraulic governor , renew worn out parts and calibrate . nt 495 mg , 24k . remove and chemically clean the lube oil cooler & fresh water cooler and carryout pressure testing . replace if required . renew all o rings and gaskets . remove after cooler air element , clean and pressure test it . replace if require . nt 495 mg , 24k . carryout injection timing . nt 495 mg , 24k . check all connecting rods for bend & twist . clean all oil passages . replace all small end bushesnt 495 mg , 24k . remove , clean and retreat the crankcase . clean , repaint bed platent 495 mg , 24k . overhaul turbocharger , renew turbocharger if excessively worn outnt 495 mg , 24k . overhaul starter motor renew all the worn out parts . repair renew of worn out parts of charging alternator , renew if required ( only electrical starter ) nt 495 mg , 24k . remove and clean lube oil pump , replace all worn out parts . replace if necessary . renew lube oil pump suction pipe and strainernt 495 mg , 24k . check and replace fresh water pump . nt 495 mg , 24k . replace all coupling rubber insertsnt 495 mg , 24k . carryout engine & alternator alignment by maintaining the crankshaft end clearancesnt 495 mg , 24k . remove all cylinder heads and dismantle valve gear . decarbonise combustion spaces . grind in valves and removal of pistons . nt 495 mg , 24k . offering da for cold checks / hot checks to trial agencies . connecting the safety devises post calibration . nt 495 mg , 24k . droop setting and load trails . nt 495 mg , 24k . renewal of sv mounts ( grouping in ndv scope ) nt 495 mg , 24k . shifting the engine to ssspl service center and backnt 495 mg , 24k . dp test for critical componentsnt 495 mg , 6k . clean and calibrate injectors . also change injector inlet screen . nt 495 mg , 6k . replace rocker cover gaskets . adjust valve tappet clearances within limits . nt 495 mg , 6k . replace fuel pump fitter ( screen and magnet ) and calibrate pt fuel pumpnt 495 mg , 6k . clean turbocharger , compressor wheel and diffuser . check turbo charger radial / end bearing clearance insite . renew 0 ring and teflon gasket when turbocharger is opened for checking clearances . nt 495 mg , 6k . torque manifold nuts or cap screws as per specifications . nt 495 mg , 6k . drain coolant . flush through using restore plus as laid down in operating manual . renew coolant . nt 495 mg , 6k . check sw and fw pumps for performance / defects and overhaul if required pumps replacement onlynt 495 mg , 6k . inspect idler and drive gears . nt 495 mg , 6k . check thickness of vibration damper at 0 , 90 , 180 and 270 degree positions . replace damper if variation of the 4 readings exceeds 0 . 010 inch ( 0 . 25mm ) or exceeds max allowable thickness . checks to be undertaken in coupled condition . nt 495 mg , 6k . check crank end clearances with a dial indicator , attaching against damper min 0 . 13mm . max 0 . 51mm . nt 495 mg , 6k . undertake alignment checks between the generator and engine and restore radial / axial limits . nt 495 mg , 6k . remove and chemically clean lub oil cooler and fresh water cooler and carryout pressure testing . renew gasket and o seal . nt 495 mg , 6k . cold checks , hot checks & trials . nt 495 mg , mandatory spares . kit , liner . bm98224 , mandatory spares . lockplate . 3009213 , mandatory spares . kit piston and ring set . kit4105239 , mandatory spares . set , main bearing ( std ) . 3240000 , mandatory spares . bearing , connecting rod . 203670 , mandatory spares . bolt , connecting rod . 9195 3 , mandatory spares . nut , heavy hexagon . 69936 , mandatory spares . washer , plain . 3025100 , mandatory spares . gasket , cylinder head . bm54940 , mandatory spares . gasket , set . bm62427 , mandatory spares . bearing , camshaft . bm27253 , mandatory spares . bearing , thrust . 9235 1 , mandatory spares . lockplate . 127677 , mandatory spares . lockplate . 127678 , mandatory spares . lockplate . 136698 , mandatory spares . seal , o ring . 70549 , mandatory spares . screw , slotted set . 168306 , mandatory spares . nut , regular hexagon . s 212 , mandatory spares . rod , push . 3046418 , mandatory spares . rod , push . 3046431 , mandatory spares . screw , hexagon head cap . s 127 , mandatory spares . screw , hexagon head cap . s 155 , mandatory spares . seal , o ring . 3010157 , mandatory spares . gasket , oil suc connection . 157551 , mandatory spares . core , cooler . 110848 , mandatory spares . retainer cooler & ring . 110827 , mandatory spares . seal , o ring . 3019116 , mandatory spares . gasket , oil cooler support . 3008017 , mandatory spares . gasket , connection . 68210 , mandatory spares . valve , exhaust . 144911 , mandatory spares . valve , intake . 150288 , mandatory spares . guide , valve stem . 66890 , mandatory spares . insert , valve . 69965 , mandatory spares . sleeve , injector . 8901 2 , mandatory spares . collet , valve . s 2037 , mandatory spares . spring , valve . 111446 , mandatory spares . guide , valve crosshead . 123558 , mandatory spares . guide , valve spring . 3235611 , mandatory spares . retainer , valve spring . 66871 , mandatory spares . kit injector repair nt495 . 3880780 , mandatory spares . spring , compression . 166009 , mandatory spares . ball , check . 167157 , mandatory spares . connector , female . 70855 , mandatory spares . key , square . 68174 , mandatory spares . shaft , fuel pump drive . 100192 , mandatory spares . bearing , ball . s 1650 , mandatory spares . gasket governor set . kitbm68356 , mandatory spares . screen , filter . 146483 , mandatory spares . cap , fuel pump filter . 157088 , mandatory spares . drive tachometer . bm28848 , mandatory spares . hub , jaw coupling . 101918 , mandatory spares . shaft , tachometer drive . 104087 , mandatory spares . diaphragm , ful pump damper . 202897 , mandatory spares . valve , check . 4913272 , mandatory spares . seal , o ring . 3034412 , mandatory spares . elbow , plain adapter . s 1028 , mandatory spares . valve , solendid . 3240573 , mandatory spares . manifold , fuel . bm30265 , mandatory spares . manifold , fuel drain . bm31780 , mandatory spares . sleeve , wear . 190397 , mandatory spares . seal , keyway . 3008947 , mandatory spares . seal , keyway . 181236 , mandatory spares . seal , rectangular ring . 154087 , mandatory spares . adapter double drive . 3247372 , mandatory spares . pump , water . 3166497 , mandatory spares . gasket , water pump . 9097 , mandatory spares . thermostat . 135675 , mandatory spares . seal , thermostat . 186780 , mandatory spares . inhibito...

Indian Navy - Andhra Pradesh

24622497 repair rate contract for detroit engines fitted onboard enc ships , first year , services , detroit engine ( 12v71 ) , top overhaul toh lcm boats , major overhaul moh lcm boats , cylinder block reconditioning , crank shaft reconditioning , flywheel & housing checking if required replacement , cylinder head reconditioning ( each cyl . head ) , checking and reconditioning of main bearing bore , overhauling of fresh water pump , overhauling of lub oil pump , overhauling of fuel pump , chemical cleaning and pressure testing of fresh water cooler keel cooler system flushing only , chemical cleaning and pressure testing of lub oil cooler , chemical cleaning and pressure testing of return fuel oil cooler , chemical cleaning and pressure testing of exhaust manifold , air inlet filter cleaning , changing of lub oil & fuel filter ( 01 set ) , changing of control cables engine ( throttle , acc . , air shut off , fuel shut off ) each , renewal of hoses with unions ( list of inaccessible hoses ) , renewal of gauges ( each guage ) , renewal of piston rings ( each piston ) , renewal of connecting rod ( each c / rod ) , renewal of crankshaft bearing ( each brg pair ) , renewal of cylinder liner ( each cyl . liner ) , renewal of gasket ( cylinder head , cac , tc , coolers ) each , overhauling of governor , overhauling of vane blower ( each blower ) , renewal of connecting rod brgs ( each pair ) , overhauling of starter , check / replacement of rocker arm and push rod , renewal of crankshaft oil seal ring , renewal of crankshaft rear oil seal , overhauling of gear train and timing marks , changing of solenoid shut off valve , changing of thermostat element ( each th . ) , calibration of pressure temp switch , assembling the cylinder head and changing of gasket ( each cyl . head ) , all exhaust valve replacement , setting and renewal of seal , calibration / changing of fuel injector ( each inj . ) , changing of injector tube ( each tube ) , decarbonization of cylinder head ( each head ) , chemical cleaning and pressure testing of cylinder head ( each head ) , fuel rack adjustment , governor setting , tappet setting , check all instrumentation for working , crankshaft deflection reading , renewal of piston assy with piston installation kit , gauging / reconditioning of camshaft assy , renewal of camshaft bearings , renewal of camfollowers , valve bridges , shafts , springs , washers of cylinder head assy , renewal of vibration damper , overhauling of accumulator pump , overhauling of hand charging pump , cleaning and inspection of steering gear pump , renewal of steering gear pump , repair / renewal of sea water pump , detroit edg ( 12v71t ) , top overhaul toh edg , major overhaul moh edg , cylinder block reconditioning , crank shaft reconditioning , flywheel & housing checking if required replacement , cylinder head reconditioning ( each cyl . head ) , checking and reconditioning of main bearing bore , overhauling of turbocharger ( each turbo ) , overhauling of fresh water pump , overhauling of lub oil pump , overhauling of fuel pump , chemical cleaning and pressure testing of fresh water cooler , chemical cleaning and pressure testing of lub oil cooler , chemical cleaning and pressure testing of return fuel oil cooler , chemical cleaning and pressure testing of air cooler , chemical cleaning and pressure testing of exhaust manifold , air inlet filter cleaning , changing of lub oil & fuel filter ( 01 set ) , changing of control cables engine ( throttle , acc . , air shut off , fuel shut off ) each , renewal of hoses with unions each one for a particular system . , checking and calibration of pyrometer scanner , if required replace pyrometer probe with cable , renewal of gauges ( each guage ) , renewal of piston rings ( each piston ) , renewal of connecting rod ( each c / rod ) , renewal of crankshaft bearing ( each brg pair ) , renewal of cylinder liner ( each cyl . liner ) , renewal of gasket ( cylinder head , cac , tc , coolers ) each , renewal of governor , overhauling of vane blower ( each blower ) , renewal of connecting rod brgs ( each pair ) , overhauling of starter , electrical system checks of pyrometer and starting solenoid , check / replacement of rocker arm and push rod , renewal of crankshaft oil seal ring , renewal of crankshaft rear oil seal ring , overhauling of gear train and timing marks , changing of solenoid shut off valve , changing of thermostat element ( each th . ) , calibration of pressure temp switch , assembling the cylinder head and changing of gasket ( each cyl . head ) , all exhaust valve replacement , setting and renewal of seal , calibration / changing of fuel injector ( each inj . ) , changing of injector tube ( each tube ) , decarbonization of cylinder head ( each head ) , chemical cleaning and pressure testing of cylinder head ( each head ) , fuel rack adjustment , governor setting , tappet setting , check all instrumentation for working each , crankshaft deflection reading , renewal of pisotn assy with piston installation kit , gauging / reconditioning of camshaft assy , renewal of camshaft bearings , renewal of camfollowers , valve bridges , shafts , springs , washers of cylinder head assy , renewal of vibration damper , renewal of silencer , spares , detroit engine and edg , stud , 3 / 8 16 / 24x1 13 / 16 , pin , 3 / 16x1 / 2 dowel ( 12 . 9290 ) , washer , 1 . 125o . d . x . 656i . d . ( 1 . 3140 ) , bolt , 5 / 8 11 x 6 . 62 12 pt main brg cap ( 1 . 3140 ) , pin , 5 / 16x3 / 8 dowel , bolt , 5 / 8 11 x 6 . 01 6 pt main brg cap ( 1 . 3140 ) , plug , 2 cup ( 1 . 2001 ) , cap , crankshaft main bearing ( unfinished ) ( 1 . 3110 ) , plug , 5 / 16 spl cup , plug , 1 5 / 8 cup ( stainless steel ) , plug , 2 1 / 2 16 , gasket , 2 . 75x . 063 plug , plug , 2 1 / 4 cup ( stainless ) ( 1 . 1001 ) , plug , 1 1 / 4 cup ( 1 . 1001 ) , pin , 1 / 2x1 5 / 8 dowel , plug , 1 / 4x5 / 16 pipe , cap , crankshaft main bearing ( finished ) ( 1 . 3110 ) , bolt , 5 / 16 18x1 flg . hex . hd . lk ctd ( 12 . 9001 ) , plug , 3 / 4 pipe ( 12 . 9550 ) , plug , pipe 1 / 4 18 nptf , plug , 1 / 2 pipe ( 12 . 9550 ) , draincock , 1 / 4 ( 12 . 9510 ) , plug , 3 / 8 18 sq . soc . vibra seal ( 12 . 9550 ) , stud 3 / 8 16 24 x 1 . 62 lg ctd thd , bolt , 7 / 16 14x1 1 / 8 lock , plug , 9 / 16 ( 9 . 3550 ) , plug , 2 1 / 8 cup , plug , 15 / 16 cup ( 2 . 7340 ) , fitting , female swiv . 3 / 8 hose 5 / 8 18 ( 12 . 6692 ) , hose , #6x75 l . ( 7 . 4699 ) , fitting , male . 38 hose 5 / 8 18 ( 2 . 5010 ) , check valve assy . ( 1 psi ) , elbow , 90 deg . 3 / 8 inv . fl . tube 1 / 4 nptf brs , connector , 3 / 8 inv . fl . tube ( 12 . 9460 ) , elbow , lockwasher , 3 / 8 , bolt , 3 / 8 16 x 1 , bolt , 3 / 8 16x2 1 / 4 , bolt , 3 / 8 16 x 1 . 25 , clip . 688 dia 3 / 8 bolt ctd ( 12 . 8554 ) , spacer , 13 / 32x3 / 4x1 / 2 ( 7 . 1581 ) , sleeve , pilot , insert , valve ( 1 . 8330 ) , nozzle , water ( double outlet ) ( 1 . 2005 ) , washer , 1 / 2x15 / 16x1 / 16 ( 1 . 8360 ) , guide , exhaust valve bridge ( 1 . 8345 ) , plug , 1 / 4 pipe , washer , 7 / 16x3 / 4 ( 2 . 4030 ) , plug , pipe 1 / 4 18 nptf , guide , exhaust valve , plug , 3 / 4 pipe ( 12 . 9550 ) , plug , 3 / 4 dia . cup ( 1 . 1001 ) , plug , 3 / 8 16 ( 12 . 001 ) , nozzle , water ( single outlet ) ( 1 . 2005 ) , plug , 7 / 16 14 ( 1 . 3160 ) , plug , fuse 1 / 8 pipe slotted hd . ( early units ) , tube kit , injector hole ( includes 5104701 seal rin , stud , 7 / 16 14 / 20x2 3 / 32 ( 6 . 1020 ) , plug , 3 / 8 18 sq . soc . vibra seal ( 12 . 9550 ) , bolt , 5 / 8 11 x 5 3 / 8 , pw , 1 / 4 stl zinc , bolt , 1 / 4 20x5 / 8 , ...

Indian Navy - Andhra Pradesh

24320741 24k routines on 04 das in ship , 04 dasdismantle auxiliary drives and check bearing clearances . renew bearings if necessary . examine all gear teeth for pitting and scuffing . kta 50 g3 , 04 dasrenew big end bearings , their bolts , nuts and washers . kta 50 g3 , 04 dascheck main bearing clearances and examine the condition . renew bearing if clearances are excessive . kta 50 g3 , 04 dasremove , clean and examine all cylinder liners for scoring and corrosion . gauge liners internally . renew if necessary . overhaul cylinder heads . kta 50 g3 , 04 dasexamine and gauge all pistons . renew pistons if necessary . kta 50 g3 , 04 dasclean all water passages . renew all sealing rings . kta 50 g3 , 04 dasremove crankshaft and check for cracks , scoring and deflection ( eccentricity ) . clean and flush out oil ways . renew teflon seals . kta 50 g3 , 04 dasoverhaul governor . renew worn out parts . calibrate governor after completion of overhauling . kta 50 g3 , 04 dasdegutting of exhaust pipelines , bellows , air intake pipes , fresh water pipelines , sea water pipelines and fuel lines & removal and fitment of gear case cover and idler gears of both rb and lb camshafts , adaptor plates for removal of cam shafts and shiftinkta 50 g3 , 04 das ( a ) remove and chemically clean lub oil cooler and fresh water cooler and carry out pressure testing . replace if required , ( b ) renew gasket and o seals . kta 50 g3 , 04 dasrefit cam shaft drive assembly . kta 50 g3 , 04 dascheck all camshaft bearing clearances . renew if necessary . check valve timing . kta 50 g3 , 04 dascheck all connecting rods for bend and twist . clean and flush out oil passages . kta 50 g3 , 04 dasrenew hp fuel pump / calibration of pt pup & injectors . kta 50 g3 , 04 dasremove , clean and retreat the crankcase . clean and repaint bedplate . kta 50 g3 , 04 dasrenew all flexible hoses . kta 50 g3 , 04 dasoverhaul turbo supercharger . renew entire unit if parts are excessively worn out . kta 50 g3 , 04 dascomplete cleaning of engine block , lub oil galleries and coolant passages . kta 50 g3 , 04 dasclean crank casekta 50 g3 , 04 dasremove air cooler , chemically clean and pressure test on completion of cleaning . replace if required . kta 50 g3 , 04 dasrenew silicon vibration damper where fitted . kta 50 g3 , 04 dasoverhaul/renew holset/ vulcan/ centamax coupling as necessary . renew the rubber inserts/ member of the flexible coupling . renew all fasteners /bolts while assembling the coupling as per oem recommended procedure . carry out engine to alternator alignment . kta 50 g3 , 04 dasremoval and fitment of fresh air blower & electrical fittings . kta 50 g3 , 04 dasremoved and fitment of exhaust trunking & air intake trunking . kta 50 g3 , 04 dascutting and fitment of acoustic canopy to facility engine tiltingkta 50 g3 , 04 daslift the engine from base plate within lifting arrangements . kta 50 g3 , 04 dastilting the engine block to 180 deg ckta 50 g3 , 04 dasremoval or renewal of lub oil sump with strainer pipes . kta 50 g3 , 04 dasshifting of removed crankshaft from engine room if main bearings are found excessive limit . kta 50 g3 , mandatory spare: nut , lock . part no:3002126 , mandatory spare: core , aftercooler . part no:3638360 , mandatory spare: seal , o ring . part no:68910 , mandatory spare: seal , rectangular strip . part no:3627381 , mandatory spare: seal , grommet . part no:3063294 , mandatory spare: seal , dust . part no:3058812 , mandatory spare: gasket , aftercooler cover . part no:3178289 , mandatory spare: gasket , connection . part no:3179028 , mandatory spare: gasket , connection . part no:3047665 , mandatory spare: screw , hexagon head cap . part no:69028 , mandatory spare: screw , hexagon head cap . part no:s 106 c , mandatory spare: tube , water transfer . part no:3050953 , mandatory spare: tube , water transfer . part no:3179850 , mandatory spare: kit , upper engine gasket . part no:4352581 , mandatory spare: tube , water transfer . part no:3179853 , mandatory spare: tube , water transfer . part no:3179856 , mandatory spare: tube , water transfer . part no:3179859 , mandatory spare: hose , flexible . part no:ak 4016 ss , mandatory spare: hose , flexible . part no:2870393 , mandatory spare: shaft , rocker lever . part no:3176772 , mandatory spare: bushing . part no:207344 , mandatory spare: bushing . part no:207226 , mandatory spare: socket , rocker lever . part no:194037 , mandatory spare: screw , slotted set . part no:168306 , mandatory spare: nut , regular hexagon . part no:s 212 , mandatory spare: plug , expansion . part no:203933 , mandatory spare: rivet . part no:208084 , mandatory spare: screw , twelve point cap . part no:205393 , mandatory spare: screw , twelve point cap . part no:205394 , mandatory spare: washer , plain . part no:205128 , mandatory spare: dowel , ring . part no:205129 , mandatory spare: screw , hexagon head cap . part no:3628194 , mandatory spare: screw , hexagon head cap . part no:3628196 , mandatory spare: housing , rocker lever . part no:3202199 , mandatory spare: housing , rocker lever . part no:3629538 , mandatory spare: cover , rocker lever . part no:3010388 , mandatory spare: pump , water . part no:4372339 , mandatory spare: seal , o ring . part no:206457 , mandatory spare: bushing . part no:3629855 , mandatory spare: pump , raw water . part no:4314522 , mandatory spare: seal , o ring . part no:3033248 , mandatory spare: bushing . part no:3014993 , mandatory spare: bearing , thrust . part no:188040 , mandatory spare: set , lower engine gasket . part no:3804300 , mandatory spare: liner , cylinder . part no:3006089 , mandatory spare: valve , piston cooling . part no:3879479 , mandatory spare: camshaft . part no:3074304 , mandatory spare: camshaft . part no:3074305 , mandatory spare: bearing , camshaft thrust . part no:3007971 , mandatory spare: bushing . part no:205230 , mandatory spare: bushing . part no:3177510 , mandatory spare: kit piston & rings . part no:kit3238277 , mandatory spare: bearing , connecting rod . part no:3047390 , mandatory spare: screw , connecting rod cap . part no:3013266 , mandatory spare: washer , plain . part no:205126 , mandatory spare: bushing . part no:3043909 , mandatory spare: dowel , pin . part no:69558 , mandatory spare: thermostat . part no:3629205 , mandatory spare: seal , thermostat . part no:186780 , mandatory spare: gasket , thermostat housing . part no:3052906 , mandatory spare: gasket , wtr trf connection . part no:3052908 , mandatory spare: valve exhaust . part no:3088389 , mandatory spare: valve intake . part no:3052820 , mandatory spare: guide valve stem . part no:3202210 , mandatory spare: spring valve . part no:3643725 , mandatory spare: insert valve seat . part no:3086192 , mandatory spare: insert valve seat . part no:3086193 , mandatory spare: collet valve . part no:205091 , mandatory spare: plug , expansion . part no:205401 , mandatory spare: plug , expansion . part no:206224 , mandatory spare: retainer , valve spring . part no:205094 , mandatory spare: rotator , valve . part no:3640315 , mandatory spare: pin , groove . part no:68445 , mandatory spare: shaft , cam follower . part no:3078218 , mandatory spare: rod , push . part no:3057139 , mandatory spare: rod , push . part no:3017961 , mandatory spare: lever , cam follower . part no:3642503 , mandatory spare: lever , camfollower . part no:3039164 , mandatory spare: tappet , hyd var timing . part no:3075381 , mandatory spare: kit barrel , plunger& cup . part no:kit3238196 , mandatory spare: clamp , injector . part no:3411695 , mandatory spare: link , injector plunger . part no:3627894 , mandatory spare: seal , o ring . part no:193736 , mandatory spare: retainer , screen . part no:174299 , mandatory spare: spring , injector . part no:3042428 , mandatory spare: ball , check . part no:167157 , mandatory spare: pin , roll . part no:203426 , mandatory spare: screen , filter . part no:3054999 , mandato...

Hindustan Shipyard Limited - Andhra Pradesh

24132111 tender for engineering equipments ( ac plant , fo , lo centrifuges , dd pump engine , ahus , fcus ) works , a / c plant no . 1 & 2 6000 hrs & nr routines . make voltas model 5h126; 6000 hourly & nr routines on ac 1 & ac 2 as mentioned below: ( 2 nos ) ; the scope of work includes removal , overhauling , refitment and commissioning , satisfactory trails of ac plant to be shown to shipastaff , hsl and all naval trial agencies; required spares and consumables are to be sourced from oem ( m / s . voltas ) ; the job is to be carriedout under supervision of oem; oem service engineer is to be arranged by contractor only . , remove and refit all isolating valves on liquid and gas lines . renew all nylon / teflon washers and seating of all valves ( brassomatic valve , mat brass ) , check all temperature gauges , pressure gauges , safety alarms and trips . rectify defects . sow includes procurement and renewal of all pressure switches , temp . switches , wiring , pcb cards , gauges , sensors , relays , solenoids and other components . ( low lub oil switch qty 02; low suction pr switch qty 02; high discharge pressure switch qty 02; differential oil pressure switch qty 02; low chilled water temp switch and sensor qty 02; loading unloading solenoid qty 06; a / c sea water pressure switch 02; display unit 02 , mpd card 04; heater 08; control panel plc 02; mcbs 04; vpd card 04; timer relay 02 ) ; contractor has to quote seperately for procurement of required spares; , renew all sv mounts post survey of seating and foundation plates . job includes grouping , fitment and attenuation check after fitment and report to be forwarded to the ship . carry out alignment checks and vibration trial on completion in presence of naval trial team / naval representative as per naval specifications . , renew compressor suction and delivery valves . 12 suction reeds and 12 discharge valves each compressor . 24 nos , a ) withdraw piston and inspect for wear and scoring . b ) measure wear down of piston rings and oil scrapper rings ( 12 pistons each ) ; c ) inspect all bearings and measure wear down . replace if necessary; d ) measure the ovality of cylinder and replace if necessary; e ) inspect unloading device for correct functioning; f ) check and repack all valve stem in the refrigerant line; g ) drain the compressor and clean the crankcase with lint free cloth . clean sight glass from inside and charge fresh oil as per required quantity; h ) withdraw piston heads and inspect valve spring , valve plate and securing arrangement; i ) firm has to procure and renew oil strainers and liquid line strainers; j ) firm has to procure and renew compressor suction strainers; k ) renew expansion valves; contractor has to quote seperately for procurement of required spares; , renew corrosion plugs . , carry out chemical cleaning of condensors , heat exchanger coils and all associated refrigerant pipe work includig gas and sea water side . carry out pressure test . rectify defects if any . sow includes removal , chemical cleaning , defect rectification , pressure testing and refitment of end plates . , all vibration dampers to be replaced with new ones . , leak test of gas system to be carried out all leaks to be rectified . post completion of work system to be pressure tested by nitrogen as per procedure and vaccumiesd for 24 hours . gas to be charged post vacuumising and system to be proved , carry out cold and hot safety devices checks before commencement and post completion of work . all pressure gauges , temperature gauges , cut outs , solenoids and thermometers are to becalibrated and all defective components are to be procured and replaced . firm has to quote seperately for procurement of all control components including pcbs , sensors , indications , hooters and cutouts . all items are to be sourced from oem / authorised dealer and a detailed report including calibration certificates is to be forwarded to ship . instrumentation . pr gauge 07 each temp gauges 04 each sea water pr . switch 01 each chilled water pr switch 01 each temp switch 01 each sensors 04 each cut outs 03 each mpd 0 1 each control cards 05 each thermometer 08 each solenoids 03 each expn valve 01 each misc . components as fitted , all gas system relief valves to be calibrated and replaced with new valves and calibration certificates to be provided to ships . outlet of all gas system relief valves to be directed to atmosphere and tail pipes of adequate strengths and length to be manufactured and fitted along with end fittings . , consumables / components / items / spares / material: contractor has to quote lumpsum cost for the entire sow ( i . e . s . no 1 to s . no 12 line items in our boq ) , against third party / oem invoice for all spares supplied for the scope . the taxes will be paid as per actuals . the cost of spares quoted by the contractor will be considered on not exceeding basis of total lumpsum cost mentioned in the boq for satisfactory completion of the specified sow . payment will be made at actuals on not exceeding quoted cost of this serial ( 13 ) against third party invoices / oem invoice ( as applicable ) . any cost implication towards spares beyond this lumpsum cost is to be borne by contractor . , ac control panel ( 2 nos ) , remove the control panel from ship and shift to shop floor . carry out calibration and overhauling of compressor motor and starter with safty cut out . starter body to be painted . , all internal wiring , indication lamp ( 08 nos ) , terminal blocks and knobs ( 06 nos ) to be replaced . , over load relay to be procured and replaced . over load to be calibrated before fitment and calibration certificate to be provided to ss . , mccb to be procured and replaced . , vendor to procure and replace the contacts of main contactor ( 110 amps ) 02 nos , star contactor ( 110 amps ) 02 nos and delta contactor ( 110 amps ) 02 nos . , control panel to be offered for trials to ss after assembling at shop floor . , procure and replace lpc with plc based card , vpd , mpd and contactors in both control panels; model: mhcdr1100ma & capacity: 332640kcal / hr; , fit the control panel in ship with earthing strap and take trials with motor . , check and overhaul all starters of motors ( routine to be undertaken in conjunction with electrical dept ) , consumables / components / items / spares / material: contractor has to quote lumpsum cost for the entire sow ( i . e . s . no 14 to s . no 23 line items in our boq ) , against third party / oem invoice for all spares supplied for the scope . the taxes will be paid as per actuals . the cost of spares quoted by the contractor will be considered on not exceeding basis of total lumpsum cost mentioned in the boq for satisfactory completion of the specified sow . payment will be made at actuals on not exceeding quoted cost of this serial ( 24 ) against third party invoices / oem invoice ( as applicable ) . any cost implication towards spares beyond this lumpsum cost is to be borne by contractor . , routines on ahus and fcus: the scope of work includes removal , overhauling / servicing , refitment and commissioning , satisfactory trails of ahus and fcus to be shown to shipastaff , hsl and all naval trial agencies; required spares , materials and consumables are to be supplied by contractor only . pressure testing of ahus and fcus are covered in contractors scope . new ahus , new fcus will be supplied by hsl anf fitment of new ahus , new fcus are included in contractors scope . lifting , shifting and installation of new ahus , new fcus onboard is covered in contractors scope . any...

Indian Navy - Andhra Pradesh

24114884 repair rate contract for detroit engines fitted onboard enc ships repair rate contract for detroit engines fittedonboard enc ships , first year , services , detroit engine ( 12v71 ) services , top overhaul toh lcm boats , major overhaul moh lcm boats , cylinder block reconditioning , crank shaft reconditioning , flywheel & housing checking if required replacement , cylinder head reconditioning ( each cyl . head ) , checking and reconditioning of main bearing bore , overhauling of fresh water pump , overhauling of lub oil pump , overhauling of fuel pump , chemical cleaning and pressure testing of fresh water cooler keel cooler system flushing only , chemical cleaning and pressure testing of lub oil cooler , chemical cleaning and pressure testing of return fuel oil cooler , chemical cleaning and pressure testing of exhaust manifold , air inlet filter cleaning , changing of lub oil & fuel filter ( 01 set ) , changing of control cables engine ( throttle , acc . , air shut off , fuel shut off ) each , renewal of hoses with unions ( list of inaccessible hoses ) , renewal of gauges ( each guage ) , renewal of piston rings ( each piston ) , renewal of connecting rod ( each c/rod ) , renewal of crankshaft bearing ( each brg pair ) , renewal of cylinder liner ( each cyl . liner ) , renewal of gasket ( cylinder head , cac , tc , coolers ) each , overhauling of governor , overhauling of vane blower ( each blower ) , renewal of connecting rod brgs ( each pair ) , overhauling of starter , check/replacement of rocker arm and push rod , renewal of crankshaft oil seal ring , renewal of crankshaft rear oil seal , overhauling of gear train and timing marks , changing of solenoid shut off valve , changing of thermostat element ( each th . ) , calibration of pressure temp switch , assembling the cylinder head and changing of gasket ( each cyl . head ) , all exhaust valve replacement , setting and renewal of seal , calibration/changing of fuel injector ( each inj . ) , changing of injector tube ( each tube ) , decarbonization of cylinder head ( each head ) , chemical cleaning and pressure testing of cylinder head ( each head ) , fuel rack adjustment , governor setting , tappet setting , check all instrumentation for working , crankshaft deflection reading , renewal of piston assy with piston installation kit , gauging/reconditioning of camshaft assy , renewal of camshaft bearings , renewal of camfollowers , valve bridges , shafts , springs , washers of cylinder head assy , renewal of vibration damper , overhauling of accumulator pump , overhauling of hand charging pump , cleaning and inspection of steering gear pump , renewal of steering gear pump , repair/renewal of sea water pump , detroit edg ( 12v71 t ) services , top overhaul toh lcm boats , major overhaul moh lcm boats , cylinder block reconditioning , crank shaft reconditioning , flywheel & housing checking if required replacement , cylinder head reconditioning ( each cyl . head ) , checking and reconditioning of main bearing bore , overhauling of fresh water pump , overhauling of lub oil pump , overhauling of fuel pump , chemical cleaning and pressure testing of fresh water cooler keel cooler system flushing only , chemical cleaning and pressure testing of lub oil cooler , chemical cleaning and pressure testing of return fuel oil cooler , chemical cleaning and pressure testing of exhaust manifold , air inlet filter cleaning , changing of lub oil & fuel filter ( 01 set ) , changing of control cables engine ( throttle , acc . , air shut off , fuel shut off ) each , renewal of hoses with unions ( list of inaccessible hoses ) , renewal of gauges ( each guage ) , renewal of piston rings ( each piston ) , renewal of connecting rod ( each c/rod ) , renewal of crankshaft bearing ( each brg pair ) , renewal of cylinder liner ( each cyl . liner ) , renewal of gasket ( cylinder head , cac , tc , coolers ) each , overhauling of governor , overhauling of vane blower ( each blower ) , renewal of connecting rod brgs ( each pair ) , overhauling of starter , check/replacement of rocker arm and push rod , renewal of crankshaft oil seal ring , renewal of crankshaft rear oil seal , overhauling of gear train and timing marks , changing of solenoid shut off valve , changing of thermostat element ( each th . ) , calibration of pressure temp switch , assembling the cylinder head and changing of gasket ( each cyl . head ) , all exhaust valve replacement , setting and renewal of seal , calibration/changing of fuel injector ( each inj . ) , changing of injector tube ( each tube ) , decarbonization of cylinder head ( each head ) , chemical cleaning and pressure testing of cylinder head ( each head ) , fuel rack adjustment , governor setting , tappet setting , check all instrumentation for working , crankshaft deflection reading , renewal of piston assy with piston installation kit , gauging/reconditioning of camshaft assy , renewal of camshaft bearings , renewal of camfollowers , valve bridges , shafts , springs , washers of cylinder head assy , renewal of vibration damper , overhauling of accumulator pump , overhauling of hand charging pump , cleaning and inspection of steering gear pump , renewal of steering gear pump , repair/renewal of sea water pump , spares , stud , 3/8 16/24x1 13/16 , pin , 3/16x1/2 dowel ( 12 . 9290 ) , washer , 1 . 125o . d . x . 656i . d . ( 1 . 3140 ) , bolt , 5/8 11 x 6 . 62 12 pt main brg cap ( 1 . 3140 ) , pin , 5/16x3/8 dowel , bolt , 5/8 11 x 6 . 01 6 pt main brg cap ( 1 . 3140 ) , plug , 2 cup ( 1 . 2001 ) , cap , crankshaft main bearing ( unfinished ) ( 1 . 3110 ) , plug , 5/16 spl cup , plug , 1 5/8 cup ( stainless steel ) , plug , 2 1/2 16 , gasket , 2 . 75x . 063 plug , plug , 2 1/4 cup ( stainless ) ( 1 . 1001 ) , plug , 1 1/4 cup ( 1 . 1001 ) , pin , 1/2x1 5/8 dowel , plug , 1/4x5/16 pipe , cap , crankshaft main bearing ( finished ) ( 1 . 3110 ) , bolt , 5/16 18x1 flg . hex . hd . lk ctd ( 12 . 9001 ) , plug , 3/4 pipe ( 12 . 9550 ) , plug , pipe 1/4 18 nptf , plug , 1/2 pipe ( 12 . 9550 ) , draincock , 1/4 ( 12 . 9510 ) , plug , 3/8 18 sq . soc . vibra seal ( 12 . 9550 ) , stud 3/8 16 24 x 1 . 62 lg ctd thd , bolt , 7/16 14x1 1/8 lock , plug , 9/16 ( 9 . 3550 ) , plug , 2 1/8 cup , plug , 15/16 cup ( 2 . 7340 ) , fitting , female swiv . 3/8 hose 5/8 18 ( 12 . 6692 ) , hose , #6x75 l . ( 7 . 4699 ) , fitting , male . 38 hose 5/8 18 ( 2 . 5010 ) , check valve assy . ( 1 psi ) , elbow , 90 deg . 3/8 inv . fl . tube 1/4 nptf brs , connector , 3/8 inv . fl . tube ( 12 . 9460 ) , elbow , lockwasher , 3/8 , bolt , 3/8 16 x 1 , bolt , 3/8 16x2 1/4 , bolt , 3/8 16 x 1 . 25 , clip . 688 dia 3/8 bolt ctd ( 12 . 8554 ) , spacer , 13/32x3/4x1/2 ( 7 . 1581 ) , sleeve , pilot , insert , valve ( 1 . 8330 ) , nozzle , water ( double outlet ) ( 1 . 2005 ) , washer , 1/2x15/16x1/16 ( 1 . 8360 ) , guide , exhaust valve bridge ( 1 . 8345 ) , plug , 1/4 pipe , washer , 7/16x3/4 ( 2 . 4030 ) , plug , pipe 1/4 18 nptf , guide , exhaust valve , plug , 3/4 pipe ( 12 . 9550 ) , plug , 3/4 dia . cup ( 1 . 1001 ) , plug , 3/8 16 ( 12 . 001 ) , nozzle , water ( single outlet ) ( 1 . 2005 ) , plug , 7/16 14 ( 1 . 3160 ) , plug , fuse 1/8 pipe slotted hd . ( early units ) , tube kit , injector hole ( includes 5104701 seal rin , stud , 7/16 14/20x2 3/32 ( 6 . 1020 ) , plug , 3/8 18 sq . soc . vibra seal ( 12 . 9550 ) , bolt , 5/8 11 x 5 3/8 , pw , 1/4 stl zinc , bolt , 1/4 20x5/8 , bolt , 1/4 20x1/2 ( w/seal patch ) ( 12 . 9001 ) , cover ...

Indian Navy - Andhra Pradesh

23989345 one time repair to undertake 6k hourly routines on l2 da of ins shivalik one time repair to undertake 6k hourly routines on l2 da of ins shivalik , services , fuel system ( a ) clean and calibrate injectors inlet screen . ( b ) replace rocker cover gaskets . ( c ) adjust valve tappet clearance within limit . ( d ) replace fuel pump filter ( screen and magnet ) ( e ) calibrate pt fuel pump , air system ( a ) clean turbocharger , compressor wheel and diffuser . ( b ) check turbo charger radial / end bearing clearance . note: renew o ring and teflon gasket when turbocharger is opened for checking for clearances ( c ) torque manifold nuts or cap screw as per specifications , cooling system ( a ) charge air cooler and fresh water cooler ( b ) ( i ) clean the internal passages of charge air cooler and fresh water cooler coolant side using restore plus as laid down in operating manual . ( ii ) renew coolant in the system ( iii ) inspection charge air cooler air side and if required clean using hot water and pressure test up to 2 kg / cm2 , misc routines , check thickness of vibration damper at 0 , 90 , 180 and 270 degree , positions . replace damper if variation of the 4 readings exceeds 0 . 010 inch ( 0 . 25mm ) or exceeds max , check crank end clearances with a dial indicator , attaching against damper min 0 . 13 mm , max 0 . 51 mm . , tighten mounting bolts / nut as required , spares , gasket sets , kit , upper engine gasket , injectors , tappet , hyd var timing , kit barrel , plunger& cup , seal , o ring , retainer , screen , spring , injector , ball , check , pin , roll , screen , filter , plug , threaded , link injector plunger , seal injector , cap tappet top stop , nut tappet top stop lock , clamp injecor , turbocharger , kit , turbo repair hc5a , nut , lock , screw , hex flange head cap , gasket , turbocharger , gasket , connection , hose flexible , hose flexible , fuel pump , gasket governor set , bearing , ball , knob , shield , shutoff valve , screen , filter , cover , fuel pump front , seal , o ring , shaft , fuel pump drive , key , square , cap , fuel pump filter , valve , check , kit , seal , gear , tachometer drive , screw , hexagon head cap , pump , gear fuel , seal , o ring , seal , o ring , valve , shutoff , screen , filter , seal , o ring , cap fuel pump filter , seal , rectangular ring , housing filter , barrel & plunger , anticipatory spares , impeller , tur compressor , shaft & wheel , actuator , etr fuel control , diffuser turbocharger , slinger oil...

East Coast Railway - Andhra Pradesh

23965594 supply of , floating bushing (oil inlet to vibration damper) to dlw drg.no.19c 74706 1, alt a or latest and dlw pt.no.10130822. note: date of manufacturing should not be more than three months before the date of supply....

Indian Navy - Andhra Pradesh

23468961 tender for repair rate contract ( rrc ) for volvo penta engine d3 160 ( i c ) and d4 225 ( a e ) fitted onboard enc ships , first year , services , d3 160 ( i c ) , top overhauling , major overhauling , renewal of oil cooler , water / coolant ingress in engine , renewal of flywheel housing , renewal of big end bearings , renewal of piston & piston rings , removal &refitment of clutch , removal &refitment of sv mounts , removal &refitment of engine , overhauling of outboard drive , removal and fitment of transom shield , renewal / refitment of engine wiring harness , checking / renewal of eecu control unit , electrical works control panel to engine , electrical works trim sytem , electrical works rudder system , removal and fitment of gimble ring and pivot housing , steering hard to turn same to be rectified , removal &refitment of inner transom plate , removal and refitment of camshaft , calibration of high pressure pump , overhauling of lower gear unit , overhauling of upper gear unit , renewal / fitment of suspension fork , overhauling of steering gear unit , removal &refitment of trim pump , removal and refitment of propeller set , diagnosing fault by vodia , renewal of lubricating pump , removal and refitment of injector / injectors , removal and refitment of universal bellows , renewal of steering hoses d4 engine , chemical cleaning and pressure testing of exhaust manifold , overhauling of shift mechanism , overhauling of sea water pump , removal and fitment of starter motor , removal &refitment of exhaust manifold , removal &refitment of out board drive , overhauling of steering ram , renewal of steering hose ( each ) , decorbonizing of turbocharger , removal and fitment of high pressure pump , changing of control cables , replacement of control mechanism , removal &refitment of trim cylinder each , removal &refitment of steering ram , chemical cleaning and pressure testing of heat exchanger , chemical cleaning and pressure testing of air inter cooler , removal &refitment of timing belt with setting , renewal of sensors ( each ) , removal &reiftment of turbocharger , removal and fitment of belt tensioner , calibration of injector each , removal and fitment of alternator , renewal of exhaust elbow ( engine ) , removal &reiftment of s / w pump , renewal of zinc anodes ( each ) , renewal of drive belt , removal &refitment of filter fuel , lube each , removal &refitment of engine hose ( each ) , removal &refitment of guages each , d4 225 ( a e ) , top overhauling , major overhauling , renewal of oil cooler , water / coolant ingress in engine , renewal of flywheel housing , renewal of big end bearings , renewal of piston & piston rings , removal &refitment of clutch , removal &refitment of sv mounts , removal &refitment of engine , overhauling of outboard drive , removal and fitment of transom shield , renewal / refitment of engine wiring harness , checking / renewal of eecu control unit , electrical works control panel to engine , electrical works trim sysytem , electrical works rudder system , removal and fitment of gimble ring and pivot housing , steering hard to turn same to be rectified , removal &refitment of inner transom plate , removal and refitment of camshaft , calibration of high pressure pump , overhauling of lower gear unit , overhauling of upper gear unit , renewal / fitment of suspension fork , overhauling of steering gear unit , removal &refitment of trim pump , removal and refitment of propeller set , diagnising fault by vodia , renewal of lubricating pump , removal and refitment of injector / injectors , removal and refitment of universal bellows , renewal of steering hoses d4 engine , chemical cleaning and pressure testing of exhaust manifold , overhauling of shift mechanism , overhauling of sea water pump , removal and fitment of starter motor , removal &refitment of exhaust manifold , removal &refitment of out board drive , overhauling of steering ram , renewal of steering hose ( each ) , decorbonizing of turbocharger , removal and fitment of high pressure pump , changing of control cables , replacement of control mechanism , removal &refitment of trim cylinder each , removal &refitment of steering ram , chemical cleaning and pressure testing of heat exchanger , chemical cleaning and pressure testing of air inter cooler , removal &refitment of timing belt with setting , renewal of sensors ( each ) , removal &reiftment of turbocharder , removal and fitment of belt tensioner , calibration of injector each , removal and fitment of alternator , renewal of exhaust elbow ( engine ) , removal &reiftment of s / w pump , renewal of zinc anodes ( each ) , renewal of drive belt , removal &refitment of filter fuel , lube each , removal &refitment of engine hose ( each ) , removal &refitment of guages each , o / h of flywheel housing d4 engine , renewal of absorber d4 engine , electrical works evc d control d4 engine , o / h of heat exchanger unit d4 engine , renewal of steering pump d4 engine , renewal of shift actuator d4 engine , renewal of steering cylinder d4 engine , renewal of steering control block d4 engine , renewal of fuel feed pump , renewal of pcu d4 engine , electrical works shift actuator d4 engine , renewal of steering tie rod d4 engine , renewal of fuel cooler d4 engine , 1200 hourly routines , 200 hourly routines , 100 hourly routines , r / r super charger , r / r sea water stainer , renewal of crank sahft seal , r / r exhaust pipe , renewal of idler pully , renewal of trim hoses and tube , renewal of dc unit , r / r expansion tank , r / r sump , flushing of luberication system in engine , renewal of c . v joint , flushing of streeeing system , flushing of trim system , spares , d3 160 ( i c ) , base engine , exch , cylinder head , cap plug , cap plug , screw , flange screw , plug , valve spring washer , valve seal , valve spring , valve spring washer , valve collet , inlet valve , exhaust valve , oil filler cap , o ring , spare parts kit , sender , gasket , flange screw , screw , screw , screw , flange screw , shutter , bracket , rubber guard , cylinder head gasket , cylinder head gasket , cylinder head gasket , sealing compound , o ring , stud bolt , ball stud , sealing ring , screw , pivot , lifter , plug , sealing ring , guide sleeve , plug , gasket , locating pin , piston cooling valve , gasket , pin , guide sleeve , guide rall , flange screw , flange screw , oil pressure sesor , piston cooling jet , flange screw , fly wheel housing , flange screw , flange screw , flange screw , flange screw , nut , screw , belt protector , flange screw , belt protector , 6 point socket screw , belt protector , gear pulley , flange screw , flange screw , tooth belt , tooth belt , pulley , belt tensioner , screw , camshaft intake , camshaft exhaust , hp pump , nipple , gasket , o ring , solenoid valve , screw , connection block , flange screw , flywheel , gear ring , screw , adaptor ring , oscillation damper , connecting rod , screw , main bearing , main bearing , main bearing , main bearing , thrust bearing , bigend bearing kit , spring pin , crank shaft , pulley , vibration damper , flange screw , nut , piston kit , piston kit , piston kit , piston ring kit , screw , spring washer , flexible coupling , oil pump , 6 point socket screw , sealing ring , o ring , gasket , oil suction pipe , flange screw , o ring , plug , flange screw , screw , valve , o ring , sealing ring , oil pan , sump , dipstic , o ring , tube , clamp , nut , ferrule , suction pipe , o ring , screw , sender , o ring , rubber cushion , adjust screw , washer , nut , washer , spring washer , engine bracket ( left ) , engine bracket ( right ) , flange screw , flange screw , flange screw , flange screw , spacer sleeve , spacer sleeve , cover , oil filter housing , cover , filter insert , valve , seal , seal , hose , flange screw , vent hose , hose clamp , fuel filter kit , gasket , fuel filter , screw , ...

Indian Navy - Andhra Pradesh

23043001 rate repair contract of volvo penta d3 170 ( a g ) , d6 310 ( a e ) & d6 330 ( a f ) : top overhauling d3 , top overhauling d6 , major overhauling d3 , major overhauling d6 , renewal of oil cooler d3 , water / coolant ingress in engine , renewal of flywheel housing , renewal of big end bearings , renewal of piston & piston rings , removal & refitment of clutch , removal & refitment of sv mounts , removal & refitment of engine , overhauling of outboard drive , removal and fitment of transom shield , renewal / refitment of engine wiring harness , checking / renewal of eecu control unit , electrical works control panel to engine , electrical works trim sysytem , electrical works rudder system , removal and fitment of gimble ring and pivot housing d3 , steering hard to turn same to be rectified , removal & refitment of inner transom plate , removal and refitment of camshaft , calibration of high pressure pump , overhauling of lower gear unit , overhauling of upper gear unit , renewal / fitment of suspension fork , overhauling of steering gear unit d3 , removal & refitment of trim pump , removal and refitment of propeller set , diagnising fault by vodia , renewal of lubricating pump , removal and refitment of injector / injectors , renewal of steering hoses , chemical cleaning and pressure testing of exhaust manifold , overhauling of shift mechanism , overhauling of sea water pump , removal and fitment of starter motor , removal & refitment of exhaust manifold , removal & refitment of out board drive , removal and refitment of universal bellows , overhauling of steering ram d3 , renewal of steering hose ( each ) d3 , decorbonizing of turbocharger , removal and fitment of high pressure pump , changing of control cables , replacement of hcu , removal & refitment of trim cylinder each , removal & refitment of steering ram , chemical cleaning and pressure testing of heat exchanger d3 , chemical cleaning and pressure testing of he & oc combined d6 , removal & reiftment of he & oc combined d6 , chemical cleaning and pressure testing of air inter cooler , removal & refitment of timing belt with setting , renewal of sensors ( each ) , removal & reiftment of turbocharder , removal and fitment of belt tensioner , calibration of injector each , removal and fitment of alternator , renewal of exhaust elbow ( engine ) , removal & reift ment of s / w pump , renewal of zinc anodes ( each ) , renewal of drive belt , removal & refitment of filter fuel , lube each , removal & refitment of engine hose ( each ) , removal & refitment of guages each , o / h of flywheel housing , renewal of absorber , electrical works evc d control , renewal of steering pump , renewal of shift actuator , renewal of steering cylinder , renewal of steering control block d6 , renewal of fuel feed pump , renewal of pcu , electrical works shift actuator , renewal of steering tie rod , renewal of fuel cooler , 1200 hourly routines , 500 hourly routines , 200 hourly routines , 100 hourly routines , spares d3 170 ( a g ) , longblock , cylinder head , cap plug , flange screw , plug , inlet valve , exhaust valve , valve spring washer , valve stem seal , valve spring , valve spring washer , valve collet , pivot , tappet , six point socket scr , flange screw , valve cover , gasket , pressure sensor , six point socket scr , sensor , o ring , o ring , oil filler cap , cylinder head gasket , sealing compound , flange screw , sealing ring , flange screw , glow plug , flange screw , spacer sleeve , cap plug , sealing ring , guide sleeve , guide sleeve , flange screw , screw , flange screw , connection block , hollow screw , pressure sensor , gasket , sealing compound , piston cooling jet , flange screw , piston cooling valve , flywheel housing , flange screw , flange screw , flange screw , flange screw , flange nut , cover , belt protector , belt protector , flange screw , belt protector , flange screw , tooth belt , six point socket scr , flange screw , sems screw , camshaft , camshaft , gear pulley , screw , oil pump , six point socket scr , lip seal , o ring , gasket , suction line , sealing ring , flange screw , flange screw , sealing ring , sealing ring , oil sump , oil level sensor , sealing compound , oil dipstick , pipe , rubber hose , insert nipple , o ring , gear ring , screw , connecting rod , screw , big end bearing kit , main bearing , main bearing , main bearing , main bearing , main bearing , main bearing , main bearing , main bearing , main bearing , main bearing , main bearing , main bearing , thrust bearing , flange bearing , flange bearing , thrust bearing , flange bearing , thrust bearing , flange screw , piston kit , piston ring kit , flexible coupling , flange screw , rubber cushion , hexagon nut , washer , rubber cushion , hexagon screw , nut , hexagon screw , grommet , flange screw , engine casing , spacer sleeve , washer , vibration damper , flange nut , separator , lid , oil filter kit , gasket , oil filler cap , hose , sealing ring , flange screw , oil return pipe , hose , hose clamp , oil return pipe , gasket , oil cooler kit , seal , seal , hose , hose clamp , hose , flange screw , feed pump , hollow screw , fuel hose , fuel hose , bulkhead grommet , gasket , fuel filter , fuel filter , kit , temperature sensor , cross connection , fuel pipe , hose assembly , flange screw , pressure sensor , control valve , injector , retaining clamp , fuel hose , delivery pipe , delivery pipe , delivery pipe , delivery pipe , o ring kit , fuel filter , insert , hose nipple , fuel hose , wif sensor kit , exhaust pipe , gasket , flange nut , heat shield , heat shield , hose , exhaust pipe , flange screw , bellows , hose , hose , governor , vacuum pump , turbocharger , exhaust manifold , cap plug , cap plug , gasket , inlet pipe , o ring , gasket , flange screw , spacer sleeve , stud , flange nut , hose , hose clamp , stud , flange nut , oil pressure pipe , gasket , hollow screw , air cleaner , oil trap , insert , hose , hose assembly , hose , hose , hose , o ring , hose , hose , heat exchanger , insert , thermostat , gasket , o ring , hex . socket screw , o ring , pump , v ribbed belt , hose , return hose , hose , oil cooler , hose , hose clamp , hose clamp , return hose , kit , sensor , coolant pump , hose , hose , pressure sensor , housing , charge air cooler , o ring , hex . socket screw , hex . socket screw , spacer , hose , hose , hose clamp , hose , hose , v ribbed belt , belt tensioner , seawater pump , wear kit , impeller kit , screw kit , expansion tank , level guard , spacer sleeve , washer , flange screw , pressure cap , hose , hose , banjo nipple , hollow screw , gasket , hose clamp , control lever , kit , panel , cable , switch , safety strap , cable , alternator , flange screw , spacer nut , cable , governor , belt tensioner , six point socket scr , v ribbed belt , starter , cable kit , flange screw , wiring harness kit , power train control , connection block , wiring harness , converter , cable , extension cable , cable , extension cable , wiring harness , relay , wiring harness , wiring harness , relay box , relay , relay bracket , relay socket , display , sensor , position sensor , gateway , connector , cable terminal , housing , terminal , shift motor , steering cylinder , pin , split pin , anode kit , anode kit , nut , bellows kit , kit , transom shield , ring , bearing bushing , pivot pin , flange screw , housing , fitting , o ring , pad , retainer , screw , shaft , flange screw , hose , hose clamp , hose clamp , kit , hex . socket screw , kit , washer , gasket kit , trimming cylinder , trimming cylinder , kit , kit , screw , snap ring , seal , bearing , bearing carrier , flange screw , flange screw , shim , o ring , bearing , kit , nut , shim , ball bearing , ring , shim , bearing...

Indian Navy - Andhra Pradesh

22209336 tender for 6000 hourly routines on g1 da in ship: 1.01 g1 da: completely strip engine and check dimension of all working parts, examine cylinder liners for corrosion and erosion of water side. w8v 17.5 / 22 amal 1.02 g1 da: carry out crack detection test of gudgeon pin, piston, camshaft and crank shaft. carrying out the polishing / grinding of crankshaft, if required, will be on additional chargeable basis. w8v 17.5 / 22 amal 1.03 g1 da: check wear down of liner, replace if necessary. w8v 17.5 / 22 amal 1.04 g1 da: check clearance of piston rings, replace if necessary. w8v 17.5 / 22 amal 1.05 g1 da: dismantle and examine pinions and drive gears of lub oil pump. w8v 17.5 / 22 amal 1.06 g1 da: clean crankshaft oil ducts. carrying out line boring of the cylinder block parent bores due to wear & tear of engine, if required, will be on additional chargeable basis. w8v 17.5 / 22 amal 1.07 g1 da: strip and examine fuel injection pumps and overhaul on completion. recalibration is not possible. w8v 17.5 / 22 amal 1.08 g1 da: strip and examine fuel lift pump. w8v 17.5 / 22 amal 1.09 g1 da: examine cam and rollers for wear and hard mark. w8v 17.5 / 22 amal 1.1 g1 da: check clearances of connecting rods, cam shafts and main bearings. renew bearings as necessary. w8v 17.5 / 22 amal 1.11 g1 da: clean and test fuel injectors up to 130 + 2 kg / cm2. w8v 17.5 / 22 amal 1.12 g1 da: dismantle, clean and grind the inlet, exhaust valves and reset tappet clearances ( inlet 0.3mm and exhaust 0.4mm cold ) . w8v 17.5 / 22 amal 1.13 g1 da: dismantle and clean sleeve spring, torsional vibration damper. replace broken springs, check that lub oil passage is clean in damper. w8v 17.5 / 22 amal 1.14 g1 da: carry out pressure test of all cooling water chambers for leak especially the packing of cylinder liners against the crankcase. w8v 17.5 / 22 amal 1.15 g1 da: turn the engine block upside down, remove the crankshaft for inspection. w8v 17.5 / 22 amal 1.16 g1 da: overhaul lub oil strainer, lub oil filter media and by pass valve. w8v 17.5 / 22 amal 1.17 g1 da: clean cooling water space in the turbine casing. w8v 17.5 / 22 amal 1.18 g1 da: dismantling, clean and overhaul the ( vtr 160l ) turbocharger. w8v 17.5 / 22 amal 1.19 g1 da: dismantle, de scale, overhaul and reassemble fresh water & sea water pumps. w8v 17.5 / 22 amal 1.2 g1 da: dismantle the mechanical governor and overhaul the same. w8v 17.5 / 22 amal 1.21 g1 da: check the engine and alternator alignment. w8v 17.5 / 22 amal 1.22 g1 da: check peak pressure of all cylinder heads. w8v 17.5 / 22 amal 1.23 g1 da: polishing of the crankshaft ( w8v ) at firm mumbai workshop, if required. w8v 17.5 / 22 amal 1.24 g1 da: grinding of crankshaft ( w8v ) to next undersize at firm mumbai workshop. w8v 17.5 / 22 amal 1.25 g1 da: in line boring of the crankcase in situ at vizag, if required. w8v 17.5 / 22 amal 1.26 g1 da: cylinder liner sleeve fitment of crankcase in situ, if required. w8v 17.5 / 22 amal 1.27 g1 da: mpi checking of crankcase ( provided by you ) internally & externally on board the vessel in situ. w8v 17.5 / 22 amal 1.28 g1 da: bend test & balancing of 07 nos. connecting rods at our workshop, if required. w8v 17.5 / 22 amal 1.29 g1 da: transportation charges ( to & fro ) from vizag to mumbai & back. w8v 17.5 / 22 amal 1.3 g1 da: proving of da with load trials with dttt for optimal performance including droop test. w8v 17.5 / 22 amal 2.01 mandatory spare: set of joints. 31.175.10.0.00 2.02 mandatory spare: set of ‘o’ rings. 31.175.30.0.00 2.03 mandatory spare: set of copper washers. 31.175.40.0.00 2.04 mandatory spare: set of split pins. 31.175.50.0.00 2.05 mandatory spare: cyl. head gasket ( 1 mm ) . 30.050.13.0.00 2.06 mandatory spare: cyl. head gasket ( 0.5 mm ) . 30.050.16.0.00 2.07 mandatory spare: fuel filter element. 30.267.12.0.00 2.08 mandatory spare: air starting valve assembly. 30.054.10.0.00 2.09 mandatory spare: inlet valve. 30.052.01.0.00 2.1 mandatory spare: exhaust valve. 30.052.02.0.00 2.11 mandatory spare: valve collet. 30.052.06.0.00 2.12 mandatory spare: valve guide bush. 30.050.04.0.00 2.13 mandatory spare: threaded core plug. 30.050.01.0.00 2.14 mandatory spare: threaded core plug. 30.050.02.0.00 2.15 mandatory spare: nut for cylinder head. 30.001.04.0.00 2.16 mandatory spare: wire circlip. 50.520.14.0.00 2.17 mandatory spare: cooling water passage pipe. 30.001.05.0.00 2.18 mandatory spare: pressure plug. 30.053.06.0.00 2.19 mandatory spare: burner insert. 30.053.07.0.00 2.2 mandatory spare: nozzle. 30.053.02.0.00 2.21 mandatory spare: fuel pump element. 30.025.91.0.00 2.22 mandatory spare: delivery valve. 30.025.92.0.00 2.23 mandatory spare: fuel h. p. pipe. 30.063.10.0.00 2.24 mandatory spare: fuel h. p. pipe. 30.063.20.0.00 2.25 mandatory spare: holder for h. p. pipe. 30.063.40.0.00 2.26 mandatory spare: cylinder liner with o rings. 30.307.10.0.00 2.27 mandatory spare: gudgeon pin bush. 30.045.05.0.00 2.28 mandatory spare: oil seal for air distributor. 50.302.66.0.00 2.29 mandatory spare: oil seal for driving shaft. 50.301.28.0.00 2.3 mandatory spare: pressure gauge ( 0 7 kg / cm2 ) . 46.244.01.0.00 2.31 mandatory spare: thermometer with casing. 30.138.30.0.00 2.32 mandatory spare: valve grinding paste. 30.137.39.0.00 2.33 mandatory spare: gasket cement. 30.137.38.0.00 2.34 mandatory spare: air starting distributor assly.. 31.011.10.0.00 2.35 mandatory spare: nozzle leak off pipe. 30.063.30.0.00 2.36 mandatory spare: piston ring set. 30.043.10.0.00 2.37 mandatory spare: coupling assly. for f / w pump. 30.238.10.0.00 2.38 mandatory spare: coupling assly. for s / w pump. 31.146.10.0.00 2.39 mandatory spare: ball bearing for driving shaft. 37.013.04.0.00 2.4 mandatory spare: spring ( tension ) . 30.028.15.0.00 2.41 mandatory spare: tension spring. 30.027.03.0.00 2.42 mandatory spare: driving gear wheel. 30.011.12.0.00 2.43 mandatory spare: clamping plate. 30.125.05.0.00 2.44 mandatory spare: thermostat element ( 60 0 c. ) . 30.182.01.0.00 2.45 mandatory spare: lub oil filter media. 30.065.10.0.00 2.46 mandatory spare: ball bearing for governor. 30.026.03.0.00 2.47 mandatory spare: ball bearing for governor. 30.026.05.0.00 2.48 mandatory spare: ball bearing for governor. 30.026.14.0.00 2.49 mandatory spare: joint for air inter cooler. 30.285.04.0.00 2.5 mandatory spare: joint for t / c bend pipe. 30.099.02.0.00 2.51 mandatory spare: joint for ex. adpt. ( 75mm ) oval. 30.228.02.0.00 2.52 mandatory spare: joint for ex. adpt. ( 75mm ) squr. 30.615.04.0.00 2.53 mandatory spare: sealing ring for ex. mfld. ( 75m. 34.025.20.0.00 2.54 mandatory spare: set bolt ( 8 x 30 ) cu. coated. 31.066.21.0.00 2.55 mandatory spare: stud ( 8 x 40 ) cu. coated. 31.066.22.0.00 2.56 mandatory spare: nut ( 8 mm ) cu. coated. 31.066.24.0.00 2.57 mandatory spare: adaptor assly. for exh. mfld.. 31.180.03.0.00 2.58 mandatory spare: paper insert for centrifuge. 30.300.27.0.00 2.59 mandatory spare: guide sleeve. 30.026.15.0.00 2.6 mandatory spare: pressure indicator valve. 30.195.10.0.00 2.61 mandatory spare: set of fasteners for engine. 31.998.07.0.00 2.62 mandatory spare: set of banjo bolts. 31.998.10.0.00 2.63 mandatory spare: set of lock washers. 31.998.11.0.00 2.64 mandatory spare: nylon washer. 31.998.18.0.00 2.65 mandatory spare: ex. temp. gauge ( 0 to 6500 c ) . 31.998.19.0.00 2.66 mandatory spare: silicon sealing compound. 31.998.20.0.00 2.67 mandatory spare: piston assembly ( s / c ) . 30.044.10.0.00 2.68 mandatory spare: pin for sleeve spring. 30.080.20.0.00 2.69 mandatory spare: sleeve spring. 30.080.04.0.00 2.7 mandatory spare: cylinder head assly. ( w / o. vlvs. ) . 30.046.10.0.00 2.71 mandatory spare: fresh water pump assembly. 30.252.01.0.00 2.72 mandatory spare: sea water pump assembly. 31.148.01.0.00 2.73 mandatory spare: con. rod brg.. 30.045.92.0.00 2.74 mandatory spare: main bearing. 30.001.84.0.00 2.75 mandatory spare: thrust bearing. 30.001.85.0.00 2.76 mandatory spare: outer bearing. 30.001.86.0.00 2.77 mandatory spare: recon. crankshaft ( u / s ) . 2.78 mandatory spare: con. rod assembly ( w / o. le brg. ) . 30.045.10.0.00...

Indian Navy - Andhra Pradesh

21791840 procurement of da spraes vta 1710mg 1 seal oil 2 seal o ring 3 gasket, cylinder head 4 con rod bearings 5 tappet valve 6 belt tensioning for sw pu 7 guide, valve steam 8 insert ( see eq 200kw cx 483 ) 9 washer sealing 10 gasket, filter 11 nut lock 12 washer plain 13 nut lock 14 tank, expansion 15 plug, expansion 16 nut, heavy hexagon jam 17 shaft rocker lever 18 hose flexible 19 pump gear fuel 20 collet, valve 21 cap screw 22 ammeter 23 screw, pan head cap 24 cap, filler 25 pump, lubricating oil 26 impeller, tur compressor 27 shaft and wheel 28 gasket, heat exchanger 29 head cylinder 30 retainer, seal 31 ring retaining 32 hose plain 33 seal rectangular 34 disc intermediate 35 screw hex flange head cap 36 fuel pump 37 seal injector 38 seal, o ring 39 gasket, exhaust manifold 40 plug , injector orifice 41 restore plus 1 gallon 42 hose flexible 43 ring oil piston 44 hose, flexible 45 breather 46 control governor 47 strip test 48 belt, vee 49 gasket, connection 50 belt, vee 51 seal oil 52 connection heat exhanger 53 clamp, t bolt 54 hose flexible 55 camshaft 56 impeller tur compressor 57 shaft & wheel 58 seal, rectangular strip 59 kit barel plunger & cup 60 vibration damper 61 shaft, rocker lever 62 gasket, water pump 63 clamp bolt for intake manifold 64 bearing main ( std ) 65 screw, hexagon head cap 66 seal grommet 67 pump, water 68 pump, sea water 69 valve exhaust 70 o ring 71 switch, key 72 gasket, oil suc connection 73 hose plain 74 element lub oil filter 75 gear lub oil pumping 76 ring rubber 77 nut crosshead 78 kit injector repair nt495 79 housing cam follower 80 hose plain 81 cable tachometer 82 meter hour 83 pulley, sea water pump 84 element, oil bypass filter 85 dowel diamond 86 harness wiring 87 hose, hump 88 gasket 89 seal o ring 90 gasket, rkr lever housing 91 screw, hexagon head cap 92 hose flexible 93 kit, turbo repair 4lg 94 set piston ring 95 seal, rectangular ring 96 rubber block 97 hose flexible 98 washer plain 99 vacuum indicator 100 bushing 101 washer, sealing 102 element, air cleaner 103 sleeve 104 adapter straight 105 valve, air relay 106 shim 107 gasket, flange 108 screw, slotted set 109 hose plain 110 elbow plain hexgon 111 nut, heavy hexagon 112 nut lock 113 shim 114 element oil bypass filter 115 belt, v 116 connection, adapter 117 screw, hexagon head cap 118 screw, hexagon head cap 119 magnetic pick up 120 gasket, breather 121 switch l.o.safety control, pressure 122 cap screw 123 gasket, oil cooler support 124 core aft 125 sensor temperature 126 gasket after cooler cover 127 hose flexible 128 seal o ring 129 front seal, wearsleeve kit 130 washer sealing 131 bushing 132 stud 133 screw hex flange head cap 134 gasket, exh out connection 135 seal o ring 136 washer sealing 137 gasket acc drive cover 138 nut hexagon flange 139 bearing connecting rod 140 bearing connecting rod 141 sleeve salvage 142 gasket turbocharger 143 seal oil 144 exchanger heat 145 tube injector fuel supply 146 belt v ribbrd 147 hose flexible 148 gasket fuel pp 149 tank fuel 150 seal o ring 151 seal o ring 152 seal, banjo connector 153 gasket push rod cover 154 set upper engine gasket std 155 gasket oil pan 156 nut heavy hex 157 gasket, oil drain 158 tube injector fuel supply 159 bearing main 160 gasket rear cover 161 screw captive washer cap 162 plug, zinc electrod 163 tube injector fuel supply 164 tube injector fuel supply 165 seal rectangular ring 166 tube injector fuel supply 167 gasket hydraulic pp 168 hose plain 169 washer sealing 170 gasket turbocharger 171 kit engine piston 172 hose, plain 173 gasket, filter head 174 screw, hex flange head cap 175 cup injector 176 rod push 177 shaft, water pump 178 seal o ring 179 tube, water transfer 180 valve check 181 hose flexible 182 seal, o ring 183 gasket 184 gasket, cover plate 185 retainer, shaft 186 turbocharger 187 retainer, injector link 188 washer sealing 189 cap, tappet top stop 190 o ring 191 seal rectangular ring 192 gasket gear housing 193 screw, banjo connector 194 gasket, oil cooler core 195 plug threaded 196 gasket connection 197 cable 198 shaft tachometer drive 199 cleaner air 200 screen filter 201 seal, o ring 202 gasket after housing 203 shaft, fuel pump drive 204 seal rectangular ring 205 bushing 206 housing rkr 4 rm 207 tee, female pipe 208 retainer valve spring 209 cap screw 210 bearing, camshaft thrust 211 clip 212 fuel tube drain 213 seal 214 elbow male adoptor 215 pin, roll 216 plate lock 217 seal o ring 218 spring, compression 219 brace, tube 220 tube, water transfer 221 hose, assembly 222 link injector plunger 223 bushing 224 hose, flexible 225 connection water pump inlet 226 nut regular hexagon 227 nut, lock 228 bolt connecting rod 229 screw, captive washer cap 230 tee, male union 231 thermostat 232 seal, o ring 233 clamp hose 234 exhaust valve 235 shield, turbocharger heat 236 manifold, exhaust 237 hose, assembly 238 clamp hose 239 spring valve 240 hose plain 241 seal o ring 242 lever cam follower 243 seal oil 244 clamp hose 245 injector 246 hose flexible 247 impeller, tur compressor 248 kit, tur repair 249 belt, vee 250 screw banjo connector 251 hose flexible 252 seal injector 253 gasket, turbocharger 254 hose plain 255 hose plain 256 manifold air intake 257 hose, plain 258 alternator 259 kit, turbocharger 260 coupling hose 261 bearing main shell 2356 lower 262 water cooling casing pump 263 gasket, exhaust manifold...

Indian Navy - Andhra Pradesh

21688776 procurement of da spraes vta 1710mg 1 seal oil 2 seal o ring 3 gasket, cylinder head 4 con rod bearings 5 tappet valve 6 belt tensioning for sw pu 7 guide, valve steam 8 insert ( see eq 200kw cx 483 ) 9 washer sealing 10 gasket, filter 11 nut lock 12 washer plain 13 nut lock 14 tank, expansion 15 plug, expansion 16 nut, heavy hexagon jam 17 shaft rocker lever 18 hose flexible 19 pump gear fuel 20 collet, valve 21 cap screw 22 ammeter 23 screw, pan head cap 24 cap, filler 25 pump, lubricating oil 26 impeller, tur compressor 27 shaft and wheel 28 gasket, heat exchanger 29 head cylinder 30 retainer, seal 31 ring retaining 32 hose plain 33 seal rectangular 34 disc intermediate 35 screw hex flange head cap 36 fuel pump 37 seal injector 38 seal, o ring 39 gasket, exhaust manifold 40 plug , injector orifice 41 restore plus 1 gallon 42 hose flexible 43 ring oil piston 44 hose, flexible 45 breather 46 control governor 47 strip test 48 belt, vee 49 gasket, connection 50 belt, vee 51 seal oil 52 connection heat exhanger 53 clamp, t bolt 54 hose flexible 55 camshaft 56 impeller tur compressor 57 shaft & wheel 58 seal, rectangular strip 59 kit barel plunger & cup 60 vibration damper 61 shaft, rocker lever 62 gasket, water pump 63 clamp bolt for intake manifold 64 bearing main ( std ) 65 screw, hexagon head cap 66 seal grommet 67 pump, water 68 pump, sea water 69 valve exhaust 70 o ring 71 switch, key 72 gasket, oil suc connection 73 hose plain 74 element lub oil filter 75 gear lub oil pumping 76 ring rubber 77 nut crosshead 78 kit injector repair nt495 79 housing cam follower 80 hose plain 81 cable tachometer 82 meter hour 83 pulley, sea water pump 84 element, oil bypass filter 85 dowel diamond 86 harness wiring 87 hose, hump 88 gasket 89 seal o ring 90 gasket, rkr lever housing 91 screw, hexagon head cap 92 hose flexible 93 kit, turbo repair 4lg 94 set piston ring 95 seal, rectangular ring 96 rubber block 97 hose flexible 98 washer plain 99 vacuum indicator 100 bushing 101 washer, sealing 102 element, air cleaner 103 sleeve 104 adapter straight 105 valve, air relay 106 shim 107 gasket, flange 108 screw, slotted set 109 hose plain 110 elbow plain hexgon 111 nut, heavy hexagon 112 nut lock 113 shim 114 element oil bypass filter 115 belt, v 116 connection, adapter 117 screw, hexagon head cap 118 screw, hexagon head cap 119 magnetic pick up 120 gasket, breather 121 switch l.o.safety control, pressure 122 cap screw 123 gasket, oil cooler support 124 core aft 125 sensor temperature 126 gasket after cooler cover 127 hose flexible 128 seal o ring 129 front seal, wearsleeve kit 130 washer sealing 131 bushing 132 stud 133 screw hex flange head cap 134 gasket, exh out connection 135 seal o ring 136 washer sealing 137 gasket acc drive cover 138 nut hexagon flange 139 bearing connecting rod 140 bearing connecting rod 141 sleeve salvage 142 gasket turbocharger 143 seal oil 144 exchanger heat 145 tube injector fuel supply 146 belt v ribbrd 147 hose flexible 148 gasket fuel pp 149 tank fuel 150 seal o ring 151 seal o ring 152 seal, banjo connector 153 gasket push rod cover 154 set upper engine gasket std 155 gasket oil pan 156 nut heavy hex 157 gasket, oil drain 158 tube injector fuel supply 159 bearing main 160 gasket rear cover 161 screw captive washer cap 162 plug, zinc electrod 163 tube injector fuel supply 164 tube injector fuel supply 165 seal rectangular ring 166 tube injector fuel supply 167 gasket hydraulic pp 168 hose plain 169 washer sealing 170 gasket turbocharger 171 kit engine piston 172 hose, plain 173 gasket, filter head 174 screw, hex flange head cap 175 cup injector 176 rod push 177 shaft, water pump 178 seal o ring 179 tube, water transfer 180 valve check 181 hose flexible 182 seal, o ring 183 gasket 184 gasket, cover plate 185 retainer, shaft 186 turbocharger 187 retainer, injector link 188 washer sealing 189 cap, tappet top stop 190 o ring 191 seal rectangular ring 192 gasket gear housing 193 screw, banjo connector 194 gasket, oil cooler core 195 plug threaded 196 gasket connection 197 cable 198 shaft tachometer drive 199 cleaner air 200 screen filter 201 seal, o ring 202 gasket after housing 203 shaft, fuel pump drive 204 seal rectangular ring 205 bushing 206 housing rkr 4 rm 207 tee, female pipe 208 retainer valve spring 209 cap screw 210 bearing, camshaft thrust 211 clip 212 fuel tube drain 213 seal 214 elbow male adoptor 215 pin, roll 216 plate lock 217 seal o ring 218 spring, compression 219 brace, tube 220 tube, water transfer 221 hose, assembly 222 link injector plunger 223 bushing 224 hose, flexible 225 connection water pump inlet 226 nut regular hexagon 227 nut, lock 228 bolt connecting rod 229 screw, captive washer cap 230 tee, male union 231 thermostat 232 seal, o ring 233 clamp hose 234 exhaust valve 235 shield, turbocharger heat 236 manifold, exhaust 237 hose, assembly 238 clamp hose 239 spring valve 240 hose plain 241 seal o ring 242 lever cam follower 243 seal oil 244 clamp hose 245 injector 246 hose flexible 247 impeller, tur compressor 248 kit, tur repair 249 belt, vee 250 screw banjo connector 251 hose flexible 252 seal injector 253 gasket, turbocharger 254 hose plain 255 hose plain 256 manifold air intake 257 hose, plain 258 alternator 259 kit, turbocharger 260 coupling hose 261 bearing main shell 2356 lower 262 water cooling casing pump 263 gasket, exhaust manifold...

Indian Navy - Andhra Pradesh

21471307 tender for 12000 hourly routines on bme in ship , 02 mesoverhauling cylinder heads , valve assemblies , guide bushes and seats . grind the valves . descale head , coolant passages . replace cylinder head gaskets . 16pa6v 280 stc , 02 mesremove and inspect all pistons , connecting rod assemblies and crank pin journals . 16pa6v 280 stc , 02 mesreplace pistons rings . check piston grooves and carry out hydraulic test of pistons . 16pa6v 280 stc , 02 mesexamine big end bearing shells and small end bushes . 16pa6v 280 stc , 02 mesremove two cylinder liners at random and check scale conditions . ( first 12000 hourly only ) 16pa6v 280 stc , 02 mesgauge bore of all liners . carry out honing of liners if required . 16pa6v 280 stc , 02 mesmeasure tooth clearance of timing gear chain and record . 16pa6v 280 stc , 02 mesinspect fuel injection pump delivery valves . replace all rubber components of fuel injection pump during the first 12000 hourly routine . thereafter inspect fuel njection pump delivery valves and check condition of springs . overhaul the pump if necessary . undertake timing & calibration checks . 16pa6v 280 stc , 02 mesrenew s / v mountings . note:12000 hourly routines shall be planned to be undertake in every alternate nr . 16pa6v 280 stc , 02 mesoverhaul fuel booster pump . examine shaft splines and serrated bush for wear , replace as necessary . replace seals / packings . 16pa6v 280 stc , 02 mesreplace cyclam packing of sea and fresh water pump . 16pa6v 280 stc , 02 meschemically clean lub oil cooler and carry out pressure test to 1 . 5 times working pressure . 16pa6v 280 stc , 02 mesinspect glacier centrifuge purifier and the moatti filter bypass part . 16pa6v 280 stc , 02 mesreplace gasket of auto clean lub oil filter16pa6v 280 stc , 02 mesoverhaul the turbo charger renew bearings . 16pa6v 280 stc , 02 mescheck self lubricator of starting air system . renew sealing ring and bushes16pa6v 280 stc , 02 mesrenew the rings of expansion joints of exhaust system . 16pa6v 280 stc , 02 mescheck the condition of expansion bellows on engine exhaust system without removing them during dismantling of cylinder heads and turbocharger . 16pa6v 280 stc , 02 mesremove clean and pressure test the h . p air reserviors to 1 . 5 times of working pressure . 16pa6v 280 stc , 02 mescheck fuel injection pump timing . 16pa6v 280 stc , 02 mescarry out water pressure test of colling water system and check for leakages . 16pa6v 280 stc , 02 mescheck cylinder heads and cylinder head safety valve assembly using test pump . 16pa6v 280 stc , 02 mescheck oil passages plug of crankshaft for tightness . check and clean oil passages of all connecting rods . 16pa6v 280 stc , 02 mesreplace crank shaft oil seals . 16pa6v 280 stc , 02 mescheck friction bush of gieslinger coupling check spring and slots for wear . replace all seals . overhaul if required . 16pa6v 280 stc , 02 mes36 cylinder heads need to be lifted as excessive lub oil leakage observed from bottom side . 16pa6v 280 stc , 02 mesflywheel: heavy lub oil leakage observed from flywhhel on bme . flywheel to be removed , o ring replacing & boxing back16pa6v 280 stc , 02 mesoverhauling of moatti lo filter hydraulic motor & ultrasonic cleaning of elements16pa6v 280 stc , 02 mescheck free moment of control linkage ( fuel linkages ) 16pa6v 280 stc , 02 mesoverhaul turning gear mechanism16pa6v 280 stc , 02 mesinspect vibration damper , renew springs if necessary16pa6v 280 stc , 02 mesinspect lo safety and pressure regulating valve16pa6v 280 stc , 02 mesmeasure crankshaft deflections16pa6v 280 stc , mandatory spareround joint75 . 341 . 14 . 0 . 00 , mandatory sparegasket ( punched ) 75 . 335 . 10 . 0 . 00 , mandatory sparegasket75 . 335 . 09 . 0 . 00 , mandatory sparegasket75 . 335 . 08 . 0 . 00 , mandatory spareo ring75 . 335 . 14 . 0 . 00 , mandatory spareo ring75 . 335 . 13 . 0 . 00 , mandatory sparegasket75 . 335 . 07 . 0 . 00 , mandatory sparegasket75 . 365 . 27 . 0 . 00 , mandatory sparegasket75 . 365 . 28 . 0 . 00 , mandatory sparegasket75 . 365 . 23 . 0 . 00 , mandatory sparewasher79 . 060 . 12 . 0 . 00 , mandatory sparehelicoflex sealing joint27 . 067 . 16 . 0 . 00 , mandatory spareo ring79 . 041 . 15 . 0 . 00 , mandatory spareinjector gasket79 . 041 . 18 . 0 . 00 , mandatory spareo ring79 . 041 . 21 . 0 . 00 , mandatory spareb s ring79 . 041 . 17 . 0 . 00 , mandatory sparebush viton79 . 041 . 19 . 0 . 00 , mandatory spareinjector nozzle assembly27 . 067 . 05 . 0 . 00 , mandatory sparebush79 . 001 . 08 . 0 . 00 , mandatory spareo ring79 . 001 . 09 . 0 . 00 , mandatory sparebush79 . 001 . 11 . 0 . 00 , mandatory spareinlet valve70 . 075 . 87 . 0 . 00 , mandatory sparevalve seat insert inlet79 . 029 . 03 . 0 . 00 , mandatory spareexhaust valve27 . 099 . 43 . 0 . 00 , mandatory spareexhaust valve seat79 . 029 . 06 . 0 . 00 , mandatory sparevalve guide27 . 023 . 22 . 0 . 00 , mandatory sparering79 . 029 . 39 . 0 . 00 , mandatory sparegasket for cyl . head79 . 029 . 32 . 0 . 00 , mandatory spareo ring / sealing cord74 . 466 . 02 . 0 . 00 , mandatory sparecopper washer ( 60x68 ) 50 . 508 . 51 . 000 . , mandatory sparesnap ring79 . 029 . 05 . 0 . 00 , mandatory sparering79 . 040 . 06 . 0 . 00 , mandatory spareo ring79 . 040 . 10 . 0 . 00 , mandatory spareconical spring washer ( m14 ) 50 . 527 . 10 . 000 . , mandatory sparecopper washer ( 18x24 ) 50 . 508 . 17 . 000 . , mandatory spareo ring79 . 103 . 03 . 0 . 00 , mandatory spareo ring79 . 022 . 10 . 0 . 00 , mandatory spareo ring74 . 115 . 03 . 0 . 00 , mandatory sparepiston ring top80 . 192 . 25 . 0 . 00 , mandatory sparepiston ring ( compression ) 80 . 192 . 05 . 0 . 00 , mandatory sparescrapper ring assembly80 . 192 . 15 . 0 . 00 , mandatory sparevalve seat74 . 324 . 36 . 0 . 00 , mandatory sparejoint for balmo fuel feed pump74 . 421 . 02 . 0 . 00 , mandatory spareo ring for ffp74 . 326 . 34 . 0 . 00 , mandatory spareo ring fuel feed pump74 . 326 . 35 . 0 . 00 , mandatory sparemechanical seal for ffp74 . 326 . 46 . 0 . 00 , mandatory spareserrated bush74 . 050 . 62 . 0 . 00 , mandatory sparebearing unit comp79 . 665 . 01 . 0 . 00 , mandatory sparebearing unit79 . 665 . 02 . 0 . 00 , mandatory sparesealing bush79 . 665 . 03 . 0 . 00 , mandatory sparesealing bush79 . 665 . 04 . 0 . 00 , mandatory spareguide bush79 . 665 . 05 . 0 . 00 , mandatory sparegasket by spare79 . 665 . 07 . 0 . 00 , mandatory sparegasket79 . 665 . 09 . 0 . 00 , mandatory sparepiston ring79 . 665 . 12 . 0 . 00 , mandatory sparesealing bush79 . 421 . 65 . 0 . 00 , mandatory sparerectangular gasket79 . 267 . 39 . 0 . 00 , mandatory sparerectangular joint75 . 346 . 02 . 0 . 00 , mandatory spareoval joint79 . 088 . 21 . 0 . 00 , mandatory sparemetafram bush79 . 048 . 08 . 0 . 00 , mandatory spareoil seal79 . 048 . 10 . 0 . 00 , mandatory spareloctite 54979 . 001 . 35 . 0 . 00 , mandatory spareflexible joint ( exh . manifold ) / gasket spiral wound79 . 078 . 07 . 0 . 00 , mandatory sparegasket flexiket79 . 078 . 05 . 0 . 00 , mandatory spareseal kit75 . 504 . 12 . 0 . 00 , mandatory spareseal kit75 . 503 . 12 . 0 . 00 , mandatory spareo ring79 . 143 . 08 . 0 . 00 , mandatory sparecopper washer ( 30x38 ) 50 . 508 . 35 . 000 . , mandatory sparecopper washer ( 12x16 ) 50 . 508 . 09 . 000 . , mandatory sparecon rod brg ( pair ) 80 . 021 . 95 . 0 . 00 , mandatory sparejoint79 . 125 . 04 . 0 . 00 , mandatory spareloctite 24279 . 001 . 34 . 0 . 00 , mandatory sparecyclam seal set75 . 266 . 95 . 0 . 00 , mandatory spareoil seal74 . 266 . 12 . 0 . 00 , mandatory spareroller bearing74 . 266 . 16 . 0 . 00 , mandatory spareroller cyl . brg . 79 . 068 . 12 . 0 . 00 , mandatory spareo ring74 . 266 . 18 . 0 . 00 , mandatory spareo ring74 . 266 . 19 . 0 . 00 , mandatory spareo ring74 . 266 . 20 . 0 . 00 , mandatory spareloctite 64179 . 016 . 20 . 0 . 00 , mandatory sparejoint74 . 265 . 06 . 0 . 00 , mandatory sparegasket74 . 152 . 03 . 0 . 00 , mandatory spareo ring for centrifu...

Military Engineer Services - Andhra Pradesh

18527112 tender for 24k routines on bme of in ship: 1.001 02 mes. crankshaft: measure crank web deflection and record. g 8 v 30 / 45 atl 1.002 02 mes. main brg: check / inspect main bearing and big end bearing, measure clearances and record. g 8 v 30 / 45 atl 1.003 02 mes. inspect vibration damper.. g 8 v 30 / 45 atl 1.004 02 mes. remove all piston and connecting rod for inspection, checks bearings, measure liner wear and pistons as well as piston ring clearance and record.. g 8 v 30 / 45 atl 1.005 02 mes. remove all cylinder liner and inspect water side. carry out honning if required. g 8 v 30 / 45 atl 1.006 02 mes. remove all cylinder heads clean , inspect and overhaul.. g 8 v 30 / 45 atl 1.007 02 mes. valve cover : remove clean and inspect. g 8 v 30 / 45 atl 1.008 02 mes. removal / fitment of crankcase doors. g 8 v 30 / 45 atl 1.009 02 mes. camshaft drive gear inspection : inspect gear wheels and measure backlash. g 8 v 30 / 45 atl 1.01 02 mes. camshaft drive : inspect and renew idler gear bush if required. g 8 v 30 / 45 atl 1.011 02 mes. camshaft bearing: remove, clean and inspect of 01 no. bearing shell. g 8 v 30 / 45 atl 1.012 02 mes. rocker arm: remove clean and inspect. g 8 v 30 / 45 atl 1.013 02 mes. valve drive / camshaft / cam: inspect visually all cams, rollers and check for easy movability., . g 8 v 30 / 45 atl 1.014 02 mes. inspection : inlet and exhaust valves remove and inspect all.check valve clearance. g 8 v 30 / 45 atl 1.015 02 mes. overhauling of governor drive. g 8 v 30 / 45 atl 1.016 02 mes. maintenance : remove, inspect and overhaul main starting valve, start valve and air distributor.. g 8 v 30 / 45 atl 1.017 02 mes. fip: remove, dismantle, clean inspect. g 8 v 30 / 45 atl 1.018 02 mes. fip drive: remove, inspect, clean. g 8 v 30 / 45 atl 1.019 02 mes. fuel pump regulation: inspection for smooth operation, renewal of bush and pressure spring for easy movement, adjustment of zero setting, check free movement of fuel control linkage....

Indian Navy - Andhra Pradesh

17419381 tender for procurement of spares for engine models vta 1710mgm: gasket, wtr trf connection , shaft, fuel pump drive , seal, o ring , tachometer , gasket, thermostat housing , screen filter , seal o ring , plate cover , bolt , lockplate , adapter plain , screw twelve point cap , retainer valve spring , screw, hexagon head cap , transducer , transducer , manifold exhaust , muffler , gasket, sea water pump , gasket, flange , actuator etr fuel control , seal o ring , washer plain , seal rectangular ring , connector male , hose elbow , socket, cam follower , bearing, camshaft thrust , kit, fuel filter and ring , seal, grommet , hose, plain , plate lock , seal, o ring , nipple , valve insert , cover valve , seal o ring , shaft, water pump , ring retaining , spacer seal , gasket , motor, air starting , a.v.mounting 17 / 645 s ser , pump sea water , plug expansion , ring, retaining , pump, gear fuel , plug expansion , camshaft , camshaft , shaft, rocker lever , guide, valve stem , kit barel plunger & cup , shaft & wheel , impeller tur compressor , kit turbo repair hc5a , seal, rectangular strip , vibration damper , gasket, lub oil cooler cover , spring, valve , pump, lubricating oil , set, lower engine gasket , ball bearing , nut heavy hexagon , gasket cylinder thermo , gasket turbocharger , gasket connection , seal, o ring , hose plain , hose, flexible , hose flexible , hose, flexible , seal, o ring , washer connecting rod , bushing , bush , ball connecting rod , dowel connecting rod , ring retaining , sensor, pressure , module, electronic control , kit, coolant test , inhibitor, corrosion ( premix 10 lt ) , coolant additive concentr , rivet blind...

South Central Railway - Andhra Pradesh

12942194 supply of set consiting 03 items . 1] ms 3 inch half round clamp with base and bolt nut for dust motor pipe 200 nos. 2] stud bolt camshaft vibration damper to part no. 10211056 100 nos. 3] stud bolt cam shaft vibration damper to part no. 10211044 100 nos....

South Central Railway - Andhra Pradesh

12433695 supply of set of 02 hoses as detailed below: 1 hose assembly,r/s vibration damper to sump drain of 1/2 id and 23 length qty/set: 01 no 2 hose assembly,l/s vibration damper to lube oil filling pipe of 1/2 id and 32 length qty/set: 01 no .hose to be supplied with spring gladiator and with 7/8 14unf female straight end fittings to be crimped on both ends of hose.matl specn of hose: sae 100 r5r . matl specn of end fittings: is 2062,zinc coated . make of hose: soni/ superseal/ powerflex...

South Central Railway - Andhra Pradesh

7154404 supply of set of 02 hoses as detailed below: 1 hose assembly, r/s vibration damper to sump drain, 1/2 id, length of hose assembly 23 . 2 hose assembly, l/s vibration damper to lube oil filling pipe, 1/2 id, length of hose assembly 32 . 7/8 14 unf female straight end fittings to be crimped on both ends of hose. matl.specn of hose sae 100r5r, matl specn of end fitting is 2062k zinc coated. make soni/superseal/powerflex....

Transmission Corporation Of Andhra Pradesh Limited - Andhra Pradesh

2635405 fixing of missed arcing horns, replacing the damaged/ missed dampers, providing additional vibration dampers in addition to the exiting one at cut points both sides) fixing of missed angles and uprooting of heavy bushes in 220 kv manubolu renigunta dc feeder loc no: 22 to 217...