27294789
tender for normal refit of in ship poshak 1 001 nhull sow poshak ( nr21 ) ndocking vessel to be docked in both versions. nnote 1: firms not to quote view docking, undocking and dock blocks preparation will be done by navy and the job is required to be carried out in navy premises ( i.e nd ( v ) slipway ) . nnote : last undock oct 18 2 002 nhull cleaning nunder water and boot top area n ( a ) hp jet clean entire under water area and boot top area ( with a pressure not exceeding 3000 psi ) including ship side and remove the marine growth / barnacles and present for survey. 3 002 nhull cleaning nshipside above water including bulwark and superstrcture n ( b ) hp jet clean entire shipside ( with a pressure not exceeding 3000 psi ) to remove the salts and contaminants from the surface and present for survey and present for survey. 4 002 nhull cleaning nweather deck n ( c ) hp jet clean entire weather deck including fittings ( with a pressure not exceeding 3000 psi ) remove salts and contaminants from the surface and present for survey. 5 002 nhull cleaning ntanks n ( d ) manually clean following tanks and present for survey.the tanks should be washed out with fresh water and soap water to remoeve any sediment or dirt present in the tank : wb tanks ( 09 nos ) 1100 sqm. , fuel oil tank 132 sqm., bilge holding tank 32 sqm., cargo oil tank 120 sqm., fw 180 sqm. , void spaces 200 sqm. , cofferdam 300sqm., cargo hold 190 sqm. , cable locker 45 sqm., internal compt i.e paiint store, rope store, bosun store 110 sqm., sewage tanks 33 sqm , deck store and .and engine room bilges 45 sqm. 6 003 nhull survey nexternal and internal hull survey. ncarry out visual and hammer survey ( in the presence of qc representatives ) in accordance with no 01 / 15 of under water hull, boot top area, above water hull, super structure, weather decks and all internal compartments ( i.e. fw tanks, ballast tanks, fore peak tank, engine room, steering compartment, fo tanks, cofferdams, all stiffeners and deck fittings etc.. approx. area:1800 sqm firm to submit 07 copies of hull survey report . 7 004 nutg survey ncarry out utg survey in the presence of qc representatives of u / w hull, sea tubes, sea chest and wherever recquired ie.superstructure, above water hull, weather deck, tank top etc.as per survey team. firm to submit 07 copies of hull survey report. all deck fittings to be surveyed, repaired and load tested where considered necessary.all manholes to be inspected and repaired to ensure watertightness including conduct of nchalk impression test. 8 005 nsteel renewals nquote for steel renewal at various locations as per survey report. nnote 1: quoted repair cost shall include cost of both sides blasted and primed grade `a’ quality ship building steel for shell and is 2062 grade `b’ quality steel for non structural works, degutting / regutting / renewal of all obstructions in way of steel renewals including lagging / panelling, minor fittings / equipments with their foundations, ventilation systems, staging etc., as indicated by survey team / rmt, proving of the weld runs by non destructive tests and by hose test on completion of welding, pressure testing and proving of tanks where steel renewal undertaken etc. note 2: firms to indicate cost of new panelling ( 2mm thick ) and lagging ( 2 mfmb ) material in the budgetary cost for 50 sqm each. 9 006 nbuild ups n carry out build ups as indicated by the hull survey team / surveyor n ( a ) 25 x 25 mm 150nos 10 006 nbuild ups ncarry out build ups as indicated by the hull survey team / surveyor n ( b ) 50 x50 mm 75 nos 11 007 nfairing ncarryout fairing of deformed structures as indicated by hull survey team / surveyor 12 008 nre welding run ncarry out re welding runs on weld seams as indicated by hull survey team / qc / rmt. 13 009 nsea tubes nsurface prepartion of of the sea tubes to be carried out for survey and pressure testing of sea tube including sea chest . dia 300mm 14 010 ndraught marks ndraught marks, both roman and numeric, corroded / eaten away. to be renewed and painted. 15 011 nsacrificial anodes n ( a ) renew mk i sacrificial anodes which are perished over 50%. nnote: anodes will be supplied by navy / coy. 16 011 nsacrificial anodes n ( b ) renew mk v sacrificial anodes which are perished over 50%. nnote: anodes will be supplied by navy / coy. 17 012 nsurface preparation nunder water area including boot top area with grit blasting nspot blasting to sa 2.5 on complete uw area including boot top.last paint scheme done in 2012 while induction and due for renewal as per no 53 / 16 : 18 013 npainting jotun scheme nunder water area including boot top area ncomplete uw paint scheme renewal view last paint scheme done in 2012 while induction and due for renewal as per no 53 / 16 : nnote: quoted repair cost shall be inclusive of cost of paints also. n ( a ) 1st coat: primer penguard primer 50 microns 19 013 npainting jotun scheme nunder water area including boot top area npaint under water area with following paint scheme as per oem recommendations: nnote: quoted repair cost shall be inclusive of cost of paints also. n ( b ) 2nd coat: anti corrosive jotacote universal ( aluminium ) 150 microns 20 013 npainting jotun scheme nunder water area including boot top area npaint under water area with following paint scheme as per oem recommendations: nnote: quoted repair cost shall be inclusive of cost of paints also. n ( c ) 3rd coat: anti corrosive jotacote universal ( grey ) 150 microns 21 013 n painting jotun scheme nunder water area including boot top area npaint under water area with following paint scheme as per oem recommendations: nnote: quoted repair cost shall be inclusive of cost of paints also. n ( d ) 4th coat: tie coat: safeguard es 125 microns 22 013 npainting jotun scheme nunder water area including boot top area npaint under water area with following paint scheme as per oem recommendations: nnote: quoted repair cost shall be inclusive of cost of paints also. n ( e ) 5th coat: a / f: seaquantum ultra ( brown / light red ) 150 microns 23 013 npainting jotun scheme nunder water area including boot top area npaint under water area with following paint scheme as per oem recommendations: nnote: quoted repair cost shall be inclusive of cost of paints also. n ( f ) 6th coat: a / f: seaquantum ultra ( red brown / dark red ) 150 microns 24 013 n painting jotun scheme nunder water area including boot top area npaint under water area with following paint scheme as per oem recommendations: nnote: quoted repair cost shall be inclusive of cost of paints also. n ( g ) 7th coat: a / f: seaquantum ultra ( brown / light red / black ) 150 microns 25 013 npainting jotun scheme nunder water area including boot top area n paint under water area with following paint scheme as per oem recommendations: nnote: quoted repair cost shall be inclusive of cost of paints also. n ( h ) 8th coat: a / f: seaquantum ultra ( brown / light red / black ) 150 microns 26 014 nsurface preparation nabove water area and bulwark including fittings nspot blasting to sa 2.5 on paint damaged areas / renewed plate areas as per the paint oem rep recommendation for paint application. 27 015 npainting jotun scheme. nabove water area and bulwark npaint above water area with following paint scheme as per oem recommendations: nnote: quoted repair cost shall be inclusive of cost of paints also. n ( a ) 1st coat: penguard primer 50 microns dft 28 015 npainting jotun scheme. nabove water area and bulwark npaint above water area with following paint scheme as per oem recommendations: nnote: quoted repair cost shall be inclusive of cost of paints also. n ( b ) 2nd coat: jotamastic ( grey / red brown ) 125 microns dft 29 015 npainting jotun scheme. nabove water area and bulwark npaint above water area with following paint scheme as per oem recommendations: nnote: quoted repair cost shall be inclusive of cost of paints also. n ( c ) 3rd coat: jotamastic ( grey ) 125 microns dft 30 015 npainting jotun scheme. n above water area and bulwark npaint above water area with following paint scheme as per oem recommendations: nnote: quoted repair cost shall be inclusive of cost of paints also. n ( d ) 4th coat: hard top xp grey 60 microns dft 31 016 nsurface preparation nsuper structure and deck fittings . ncarry out mechanical cleaning to st3 standard as per survey report of paint oem for paint application. 32 017 npainting jotun scheme nsuper structure and deck fittings. n paint super structure area area with following paint scheme as per oem recommendations: nnote: quoted repair cost shall be inclusive of cost of paints also. n ( a ) 1st coat: primer penguard primer 50 microns dft 33 017 npainting jotun scheme nsuper structure and deck fittings. npaint super structure area area with following paint scheme as per oem recommendations: nnote: quoted repair cost shall be inclusive of cost of paints also. n ( b ) 2nd coat: jotamastic 80 red brown 125 microns dft n 34 017 npainting jotun scheme nsuper structure and deck fittings. npaint super structure area area with following paint scheme as per oem recommendations: nnote: quoted repair cost shall be inclusive of cost of paints also. n ( c ) 3rd coat: jotamastic 80 grey 125 microns dft 35 017 npainting jotun scheme nsuper structure and deck fittings. npaint super structure area area with following paint scheme as per oem recommendations: nnote: quoted repair cost shall be inclusive of cost of paints also. n ( d ) 4th coat: hard top grey 7040 150 microns dft 36 018 nsurface preparation nweather decks bridge deck bridge top and fittings n carry out surface preperation to wj 2.0 standard by using hydro jet blasting for paint application for entire weather deck, wheel house deck, flag deck and life raft deck. 37 019 n painting jotun scheme nweather decks bridge deck bridge top and fittings npaint weather decks and fittings with following paint scheme: nnote: quoted repair cost shall be inclusive of cost of paints also. n ( a ) 1st coat: primer penguard primer 50 microns dft 38 019 n painting jotun scheme nweather decks bridge deck bridge top and fittings n paint weather decks and fittings with following paint scheme: n note: quoted repair cost shall be inclusive of cost of paints also. ( b ) 2nd coat: jotamastic 87 of 200 microns 39 019 npainting jotun scheme nweather decks bridge deck bridge top and fittings npaint weather decks and fittings with following paint scheme: nnote: quoted repair cost shall be inclusive of cost of paints also. n ( c ) 3rd coat: jota armour dark grey of 800 microns 40 020 nsurface preparation n internal compartments nfresh water tanks ( 02 nos ) and fire fighting foam tank: ncarry out mechanical cleaning to st3 standard as per survey report of paint oem for paint application. 41 021 n painting jotun scheme. nfresh water tanks ( 02 nos ) and fire fighting foam tank npaint two in no. fresh water tanks and one fire fighting foam tank with following paint scheme: nnote: quoted repair cost shall be inclusive of cost of paints also. n ( a ) 1st coat: penguard hb ( white ) 100 microns dft 42 021 n painting jotun scheme. nfresh water tanks ( 02 nos ) and fire fighting foam tank npaint two in no. fresh water tanks and one fire fighting foam tank with following paint scheme: nnote: quoted repair cost shall be inclusive of cost of paints also. n ( b ) 2nd coat: penguard hb ( grey ) 100 microns dft 43 021 npainting jotun scheme. nfresh water tanks ( 02 nos ) and fire fighting foam tank npaint two in no. fresh water tanks and one fire fighting foam tank with following paint scheme: nnote: quoted repair cost shall be inclusive of cost of paints also. n ( c ) 3rd coat: penguard hb ( white ) 100 microns dft 44 022 nsurface preparation ntanks nfore peak tanks, ballast tanks, cable locker and void spaces n ( a ) carry out mechanical cleaning to st3 standard as survey report of paint oem for paint application. 45 022 nsurface preparation ntanks nfore peak tanks, ballast tanks ( 10 no ) , cable locker n ( b ) carry out mechanical cleaning to st 1 standard as per survey report of paint oem for paint application. 46 023 n painting jotun scheme n fore peak tanks, ballast tanks ( 10 no ) , cable locker n paint fore peak tanks, ballast tanks ( 02 in no. ) and cable locker with following paint scheme. nnote: quoted repair cost shall be inclusive of cost of paints also. n ( a ) 1st coat: primer penguard primer 50 microns dft 47 023 npainting jotun scheme nfore peak tanks, ballast tanks ( 10 no ) , cable locker npaint fore peak tanks, ballast tanks ( 02 in no. ) and cable locker with following paint scheme. nnote: quoted repair cost shall be inclusive of cost of paints also. n ( b ) 2nd coat: anticorrosive balloxy ( hb light ) 150 microns 48 023 npainting jotun scheme nfore peak tanks, ballast tanks ( 10 no ) , cable locker npaint fore peak tanks, ballast tanks ( 02 in no. ) and cable locker with following paint scheme. nnote: quoted repair cost shall be inclusive of cost of paints also. n ( c ) 3rd coat: anticorrosive balloxy ( hb light ) 150 microns 49 024 n surface preparation nmachinery compartments engine room and srp n ( a ) carry out mechanical cleaning to st 3 standard as per survey report of paint oem for paint application ( bilges ) . 50 024 nsurface preparation nmachinery compartments engine room and srp n ( b ) carry out mechanical cleaning to st 1 standard as per survey report of paint oem for paint application ( bulkheads ) . 51 025 n painting jotun scheme. nmachinery bilges npaint bilges of engine room and srp compartment with following paint scheme.note: quoted repair cost shall be inclusive of cost of paints also. ( a ) 1st coat: primer penguard primer 50 microns dft 52 025 n painting jotun scheme. nmachinery bilges npaint bilges of engine room and srp compartment with following paint scheme.note: quoted repair cost shall be inclusive of cost of paints also ( b ) 2nd coat: anticorrosive jotacote universal ( aluminium ) 150 microns dft 53 025 npainting jotun scheme. nmachinery bilges npaint bilges of engine room and srp compartment with following paint scheme.note: quoted repair cost shall be inclusive of cost of paints also ( c ) 3rd coat: anticorrosive jotacote universal ( grey ) 150 microns 54 025 n painting jotun scheme. n machinery bilges npaint bilges of engine room and srp compartment with following paint scheme.note: quoted repair cost shall be inclusive of cost of paints also. ( d ) 4th coat: penguard top coat 50 microns. 55 026 nsurface preparation nmachinery compartments bulkheads of engine room and asp n ( a ) carry out mechanical cleaning to st 3 standard as per survey report of paint oem for paint application ( bilges ) . 56 026 nsurface preparation nmachinery compartments bulkheads of engine room and asp n ( b ) carry out mechanical cleaning to st 1 standard as per survey report of paint oem for paint application ( bilges ) . 57 027 npainting jotun scheme. nmachinery compartments nbulkheads of engine room and asp npaint bulkheads of engine room and srp compartments with following paint scheme nnote: quoted repair cost shall be inclusive of cost of paints also. n ( a ) 1st coat: primer penguard primer 50 microns dft 58 027 npainting jotun scheme. n machinery compartments nbulkheads of engine room and asp npaint bulkheads of engine room and srp compartments with following paint scheme: n ( b ) 2nd coat: white interior fire retardant paint 100 microns dft 59 027 nbulkhead painting. npainting jotun scheme. npaint bulkheads of engine room and srp compartments with following paint scheme: n ( c ) 3rd coat: white interior fire retardant paint 100 microns dft 60 028 ncleaning and application of oil n ( a ) fuel tanks / avcat nmanually scrap and clean fuel tank ( 10 nos ) to bare metal and apply two coats of om 750 oil. nnote: quoted repair cost shall be inclusive of cost of oil also 61 028 ncleaning and application of oil n ( b ) ru ( fods ) tanks n manually scrap and clean ru tank ( 02nos ) to bare metal and apply two coats of om 750 oil. nnote: quoted repair cost shall be inclusive of cost of oil also 62 029 nsurface preparation ntanks nlo tanks and dirty oil tanks ncarry out mechanical cleaning to st3 standard as survey report of paint oem for paint application. 63 030 npainting jotun scheme nlo tanks & dirty oil tanks npaint lo tanks & dirty oil tanks with following paint scheme. n ( a ) 1st coat: primer tankguard hb 125 microns dft nnote: quoted repair cost shall be inclusive of cost of paints also. 64 030 npainting jotun scheme nlo tanks & dirty oil tanks npaint lo tanks & dirty oil tanks with following paint scheme. n ( b ) 2nd coat: primer tankguard hb 125 microns dft nnote: quoted repair cost shall be inclusive of cost of paints also. 65 031 n gratings nopen underwater gratings, present for survey, carry out necessary repairs and refit back. 66 032 nanchor and anchor chain cable nanchor and anchor chain cable and associated fittings are to be hydro jet blasted to bare metal, eased for free movement and to present for survey at ndv mfab dept.paint with black bituminous paint post survey iaw no 12 / 2001 and refit back. note : the job involves removal of anchors and accessories, laying out for cleaning, painting and refitment. a ) anchor 67 032 nanchor and anchor chain cable nanchor and anchor chain cable and associated fittings are to be hydro jet blasted to bare metal, eased for free movement and to present for survey at ndv mfab dept.paint with black bituminous paint post survey iaw no 12 / 2001 and refit back. note : the job involves removal of anchors and accessories, laying out for cleaning, painting and refitment. b ) chain cable ( dia 32 mm ) total length of the cable 275 mtrs 68 032 nanchor and anchor chain cable nanchor and anchor chain cable and associated fittings are to be hydro jet blasted to bare metal, eased for free movement and to present for survey at ndv mfab dept.paint with black bituminous paint post survey iaw no 12 / 2001 and refit back. note : the job involves removal of anchors and accessories, laying out for cleaning, painting and c ) swivel piece 69 032 nanchor and anchor chain cable nanchor and anchor chain cable and associated fittings are to be hydro jet blasted to bare metal, eased for free movement and to present for survey at ndv mfab dept.paint with black bituminous paint post survey iaw no 12 / 2001 and refit back. note : the job involves removal of anchors and accessories, laying out for cleaning, painting nd ) lug less joining shackles 70 032 nanchor and anchor chain cable nanchor and anchor chain cable and associated fittings are to be hydro jet blasted to bare metal, eased for free movement and to present for survey at ndv mfab dept.paint with black bituminous paint post survey iaw no 12 / 2001 and refit back. note : the job involves removal of anchors and accessories, laying out for cleaning, painting and n e ) cable stopper 71 032 nanchor and anchor chain cable nanchor and anchor chain cable and associated fittings are to be hydro jet blasted to bare metal, eased for free movement and to present for survey at ndv mfab dept.paint with black bituminous paint post survey iaw no 12 / 2001 and refit back. note : the job involves removal of anchors and accessories, laying out for cleaning, painting and nf ) d shackles 72 033 nanchor windlass / capstan n ( a ) completely strip & overhaul anchor windlass ( including lub oil renewals ) , renew brake linings, refit and prove for satisfactory operation.note : overhaul involves removal of drum, gearbox, brake lining, motor and ovrhaul of all these items and refitment. oil sys 46 / hp80 73 033 ncapstan n ( b ) completely strip & overhaul capstan and prove for satifactory operation.note : overhaul involves removal of drum, gearbox, brake lining, motor and ovrhaul of all these items and refitment. oil sys 46 / hp80 74 034 nbollards nsingle bollards nfollowing single bollards corroded, thinned. entire bollard to be renewed n ( a ) single bollards, size: 290 mm dia, 10 mm thickness, 1300 mm length. schdule 80 pipe 75 034 nbollards ntwin bollards n ( b ) following twin bollards corroded, thinned. entire bollard to be repaired / renewed as per hull survey report. ndia of bollard pipe 290 mm. height of bollard 515 mm. size of bollard base / foundation1163x125x380 mm: , thickness of pipe: 10 mm. doubler plate size: 1230x480x10 mm, thickness: 10 mm, 76 035 ntyre fender ntyre fenders damaged on p&s side to be renewed with used automobile tyre fenders moulded with 8 mm layer of white natural rubber on top and outer sides. mat rubber, colour white. no painting or coating of any other form will be permitted. vendors to adhere to sow n ( a ) tyre fender od 1000 mm id 800 mm width 350 mm 77 036 ntyre fender securing arrangement ntyre fender to be secured with 14 mm dia chain on head, stern and ship side n ( a ) securing chains: 14mm dia ( mat gi ) 78 036 ntyre fender securing arrangement ntyre fender to be secured with d shackles on ship side n ( b ) d shackles 14 mm dia ( mat gi ) 79 036 ntyre fender securing arrangement nsecuring chain is to be passed through metallic sleeves inserted into the tyre fenders n ( c ) securing sleeves of dia 03 inch and length 250 mm ( mat ms pipe of 06mm thick ) 80 036 n tyre fender securing arrangement ntyre fenders securing eye plates to bo be welded along ships side for connecting of securing chains n ( d ) eye plate thickness 8 mm. ( mat ms ) 81 037 n bulwark n ( a ) bulwark at various places dented / damaged. to be included in hull in survey and renew as per survey report. thickness 6 mm 82 037 nbulwark coaming n ( b ) bulwark coaming pipes corroded and thinned. to be included in hull in survey and renewed as per survey report. dia 3 mat : ms 83 038 nsky light / port holes nsky light at various places damaged including glass. skylight / port holes is to be repaired / renewed as per sample. 84 039 nmetalic half pipe fender nmetallic half pipe fender around the shipside to be repaired / renewed. n ( a ) size 150mm dia, 08mm thick 85 039 nd shaped fenders nremoval of all d shaped fenders for survey of c channels and necessary repairs is to be attended on securing channels including nut and bolts ) . post repair of c channels damaged fenders is to be renewed details of d shaped rubber fender and associated fittings are as follows: d shaped fenders of 1000 x100x250 mm 86 039 n d shaped fenders securing arrangement c channel n fender securing arrangement corroded / thinned / holed , to be repaired as per hull survey reports 87 039 nd shaped fenders securing arrangement nut and bolts nfender securing arrangement i.e nut and bolts corroded / thinned / holed , to be renewed for securing of d fenders around ship side 88 040 nrubber beading. nrubber beading of doors at various places perished / cracked to be renewed and chalk test to be proved. as per ncd 5904 ( a ) tensile strength kg / cm2 ( min % ) 70 ( b ) elongation at break ( min % ) 350 ( c ) hardness shore a 50+ / 5 ) n ( a ) wt door 89 040 nrubber beading. nrubber beading of hatches at various places perished / crackedto be renewed and chalk test to be proved. as per ncd 5904 ( a ) tensile strength kg / cm2 ( min % ) 70 ( b ) elongation at break ( min % ) 350 ( c ) hardness shore a 50+ / 5 ) nb ) wt hatch 90 040 n rubber beading. nrubber beading of skylight perished / crackedto be renewed and chalk test to be proved. as per ncd 5904 ( a ) tensile strength kg / cm2 ( min % ) 70 ( b ) elongation at break ( min % ) 350 ( c ) hardness shore a 50+ / 5 ) n ( c ) ventilator / sky light 91 041 napt nair pressure test the following tanks and rectify the defects any observed during pressure testing and prove to 0.2 bar for 10 minutes. nnote: apt and proving of those tanks wherein steel renewel / buildup undertaken as part of steel renewal dl. 0003 ( c ) above is that of firms liability with no additional cost and those tanks where no steel renewals undertaken only would be considered for payment as per the indicated rates under this dl. serial. note: apt to be done in every 04 year, ref. no 01 / 15, last apt done in nov dec 18 ( a ) fresh water tank 92 041 napt nair pressure test the following tanks and rectify the defects any observed during pressure testing and prove to 0.2 bar for 10 minutes. nnote: apt and proving of those tanks wherein steel renewel / buildup undertaken as part of steel renewal dl. 0003 ( c ) above is that of firms liability with no additional cost and those tanks where no steel renewals undertaken only would be considered for payment as per the indicated rates under this dl. serial. n ( b ) ballast tank 93 041 napt nair pressure test the following tanks and rectify the defects any observed during pressure testing and prove to 0.2 bar for 10 minutes. nnote: apt and proving of those tanks wherein steel renewel / buildup undertaken as part of steel renewal dl. 0003 ( c ) above is that of firms liability with no additional cost and those tanks where no steel renewals undertaken only would be considered for payment as per the indicated rates under this dl. serial.. n ( c ) forepeak tank , cofferdam and void spaces 94 041 napt nair pressure test the following tanks and rectify the defects any observed during pressure testing and prove to 0.2 bar for 10 minutes. nnote: apt and proving of those tanks wherein steel renewel / buildup undertaken as part of steel renewal dl. 0003 ( c ) above is that of firms liability with no additional cost and those tanks where no steel renewals undertaken only would be considered for payment as per the indicated rates under this dl. serial. n ( d ) fuel tank , do tanks , bilge holding tank 95 041 napt nair pressure test the following tanks and rectify the defects any observed during pressure testing and prove to 0.2 bar for 10 minutes. nnote: apt and proving of those tanks wherein steel renewel / buildup undertaken as part of steel renewal dl. 0003 ( c ) above is that of firms liability with no additional cost and those tanks where no steel renewals undertaken only would be considered for payment as per the indicated rates under this dl. serial. n ( e ) firefighting foam tank 96 042 nbiilge platform n ( a ) renew bilge platform plate. material chequered aluminium, thickness 05 mm 97 042 n biilge platform n ( b ) bilge platform supporting brackets to be renewed where ever required. mat ms 98 043 ncleats nms cleats perished / thinned to be renewed ( size 28 mm ) . mat : ms 99 044 ntank / vent pipe nvent pipes of various tanks on upper deck corroded and thinned, to be renewed. ( mat. gi pipe ) n ( a ) pipe dia 2 1 / 2 inch 100 044 ntank / vent pipe nvent pipes of various tanks on upper deck corroded and thinned, to be renewed. ( mat. gi pipe ) n ( b ) distance piece and flanges: dia 150mm ( including rubber joints ) 101 045 nwt hatch clips n ( a ) hatch clips broken / damaged. to be renewed. mat. ms 102 045 nwt hatches n ( b ) hatch clips at various places jammed , to be lubricated including washer and fitted back 103 046 nwt doors n ( a ) clips of wt. doors jammed to be removed lubricated including washer, nut and fitted back 104 046 nwt hatch metal coaming n ( b ) metallic coaming of 05 in no wt hatches on weather deckand various locations corroded and thinned. to be renewed as per survey report. area 20 sqm. 105 047 ncircular hatches noprating lever of circular hatches jammed to be overhauled 106 048 nnwt doors nnwt wooden doors including frames of wheel house / crew cabin, master cabin perished / damaged. to be renewed / repaired 107 049 nventilation nmushroom type ventilators on weather deck jammed , to be removed, cleaned / overhauled and fitted beck. dia: 550mm n ( a ) 550mm dia 108 050 nventilation nmushroom type ventilators to be removed, cleaned / overhauled and fitted back. renew if required. n ( a ) details mush room head dia 1000 mm, height 800 mm 109 050 nventilation nmushroom type ventilators on weather deck jammed , to be removed, cleaned / overhauled and fitted beck. dia:360 mm n ( b ) 360mm dia 110 050 nventilation n ( c ) ventilation trunking perished to be repaired / renewed. n location: crew rest room , masters cabin, ed rest room galley / dinning hall and fitted back . nmat gi sheet 111 051 nbreather pipe nbreather pipe on weather deck perished / damage.to be renewed 112 052 nliferaft nsecuring stand of life rafts perished and damaged. to be renewed alongwith rubber lining and supporting frame, including fitment of hrg mat ms . n thickness 06mm. 113 053 n nav light nnav light foundation ( port & stbd ) corroded, to be repaired / renewed. nsize: 620mmx620mmx300mm and thickness 6mm, mat ms 114 054 ndrainage system nms scupper lips with rubber packing corroded / thinned / holed, to be renewed / repaired at ship side 115 055 ndrainage system n ( a ) deck drain pipes corroded / holed, to be renewed / repaired. dia 2 1 / 2 inch. mat: gi note : pipes / fittings should be secured with rubber packing’s and clamps uniformly 116 055 ndrainage system n ( b ) scupper with coaming of drain pipe corroded / thinned, to be renewed / repaired. size: 250mmx200mm 117 055 ndrainage system n ( c ) deck drain pieces on upper deck corroded, to be renewed / repaired. dia 2 1 / 2 inch, each of length 01mtr. note the job involves removal / repair and fitment of pipes / panelling / lagging / trunking in the way. 118 055 ndrainage system. n ( d ) soil pipes of crew, eds and masters bathroom to be removed chemically cleaned and fit back. 119 056 n pipelines ncarry out pressure testing & repairs of soil pipe / drainaige pipe / fresh water lines fitted at various locations 120 057 nsofa / cushion nsofa in master and engineer rest rooms torn / perished. to be repaired 121 058 npanelling nwooden panels in crew accommodation, engg. rest room, master rest room and other places damaged. to be repaired 122 059 nfurniture nwooden table damaged / broken at crew dinnig hall and crew cabin to be repaired. 123 060 nguard rails nguard rails pipe damaged / perished at bridge deck. to be repaired / renewed. material gi pipe . 124 061 nstanchion n ( a ) stanction on upper deck damaged / deformed at various loactions. to be repaired / renewed. size h 970 mm and dia 50 mm mat gi pipe 125 061 nstanchion n ( b ) securing chain between stanchions on upper deck damaged. to be renewed. mat ms, size 10 mm dia 126 062 nname board nfollowing tug name board perished / damaged, to be renewed / repaired. n ( a ) repair / renewal of vessel name board including electroplating to be carried out on ship side 02 127 062 nname board nfollowing tug name board perished / damaged, to be renewed / repaired. n ( b ) painting of tug name on bulwark in both hindi and english at stem and stern with fluorescent paint 03 128 062 n name board nfollowing tug name board perished / damaged, to be repaired. n ( c ) illuminated name board with perspex sheet 01 129 063 n door locks n ( a ) mortise lock of non wt door defective at various locations, all defective mortise locks to be renewed. including 03 set of keys 130 063 ndoor locks n ( b ) locking arrangement is to be provided for wt doors at various locations, including hasp & staples and pad locks 131 064. nsanitary system nss wash basin damaged in crew batroom and wc to be repaired as indicated n ( a ) wash basin 132 064 nsanitary system nss tap damaged in crew batroom and wc to be repaired as indicated n ( b ) ss tap: 1 / 2 inch 133 065 nsanitary system nsupply pipes damaged corroded / thinned / holed in crew batroom and wc to be repaired as indicated nc ) supply pipe: mat : cu ni, dia: ½’’ 134 065 n sanitary system ndrain pipes damaged corroded / thinned / holed in crew batroom and wc to be repaired as indicated nd ) drain pipe: mat ms, dia 2’’ 135 065 nsanitary system nflush valves damaged corroded / thinned / holed in crew batroom and wc to be repaired as indicated ne ) flush valves mat brass, dia 2 136 065 nsanitary system npvc wash basin drain pipe line damaged to be renewed as indicated nf ) pvc drain pipe nnote: quoted repair cost shall include cost all items. 137 066 nwc / commode nwc commode and base plate in crew wash room perished / corroded, to be renewed. mat ss 138 067 nbathroom fittings nbathroom fittings damged / broken in crew bathrooms and master bathroom , to be renewed as per sample n ( a ) cu ni supply pipes 139 067 nbathroom fittings nbathroom fittings damged / broken in crew bathrooms and master bathroom , to be renewed as per sample n ( b ) shower head 140 068 n deck underlay ndeck covering to be repaired / renewed at uprooted / damaged / steel renewed places, accommodation areas, wheel house and wet compartments. nnote: n ( a ) surface preparation and application of erop. as per ncd 3717 141 068 ndeck underlay ndeck covering to be repaired / renewed at uprooted / damaged / steel renewed places, accommodation areas, wheel house and wet compartments nnote; dry compt area 110 sqm, wet compt area 30 sqm, dadoes area 15 sqm n ( b ) application of underlay as per ncd 3717 142 068 ndeck underlay ndeck covering to be repaired / renewed at uprooted / damaged / steel renewed places, accommodation areas, wheel house and wet compartments nnote; dry compt area 110 sqm, wet compt area 30 sqm, dadoes area 15 sqm n ( c ) application of sealer coat and top coat on entire area as per ncd 3717. 143 069 nfoundation nfoundation of deck machinery / deck fittings corroded / thinned / perished , to be repaired / renewed as per survey report 144 070 nlagging nlagging at indicated places to be removed to facilitate structural repairs and to be renewed with new lagging post completion of repairs.mat ss 145 071 ndeck head panelling / sunmicia npanelling at indicated places to be removed to facilitate structural repairs and to be refitted post completion of repairs. nmat : wooden 146 072 npanelling npanelling at indicated places including wet compt to be removed to facilitate structural repairs and to be refitted post completion of repairs. mat : ss 147 073 nmanhole n ( a ) manhole covers corroded / thinned to be renewed as per survey report mat is 2062 grade b steel. size 2 x 1.5 148 073 nmanhole n ( b ) rubber joints deterioted, to be renewed 149 073 nmanhole n ( c ) studs of manholes corroded, to be renewed. only defective studs which are found defective on survey to be renewed. ms studs with nut, size 20 mm 150 nengineering work package n1001 nmain engine ( qty 02 ) , nmake cummins, model kta 38m2 marine propulsion engine, power 1350bhp, 19500rpm, sl no port ( 25344299 ) , stbd ( 25344298 ) , running hours pme 200 hrs &sme 200 hrs 151 1001 nmain engine ( qty 02 ) , nmake cummins, model kta 38m2 marine propulsion engine, power 1350bhp, 19500rpm, sl no port ( 25344299 ) , stbd ( 25344298 ) , running hours pme 200 hrs &sme 200 hrs na ) drain and clean sump. charge fresh engine oil. ( oil to provide by navy ) 152 1001 nmain engine ( qty 02 ) , nmake cummins, model kta 38m2 marine propulsion engine, power 1350bhp, 19500rpm, sl no port ( 25344299 ) , stbd ( 25344298 ) , running hours pme 200 hrs &sme 200 hrs nb ) change air cleaner element. 153 1001 nmain engine ( qty 02 ) , make cummins, model kta 38m2 marine propulsion engine, power 1350bhp, 19500rpm, sl no port ( 25344299 ) , stbd ( 25344298 ) , running hours pme 200 hrs &sme 200 hrs nc ) change fuel filter. 154 1001 nmain engine ( qty 02 ) , nmake cummins, model kta 38m2 marine propulsion engine, power 1350bhp, 19500rpm, sl no port ( 25344299 ) , stbd ( 25344298 ) , running hours pme 200 hrs &sme 200 hrs nd ) renew coolant inhibitor with zinc plugs. 155 1001 nmain engine ( qty 02 ) , make cummins, model kta 38m2 marine propulsion engine, power 1350bhp, 19500rpm, sl no port ( 25344299 ) , stbd ( 25344298 ) , running hours pme 200 hrs &sme 200 hrs ne ) renew engine oil filter. 156 1001 nmain engine ( qty 02 ) , nmake cummins, model kta 38m2 marine propulsion engine, power 1350bhp, 19500rpm, sl no port ( 25344299 ) , stbd ( 25344298 ) , running hours pme 200 hrs &sme 200 hrs nf ) renew by pass filter. 157 1001 nmain engine ( qty 02 ) , nmake cummins, model kta 38m2 marine propulsion engine, power 1350bhp, 19500rpm, sl no port ( 25344299 ) , stbd ( 25344298 ) , running hours pme 200 hrs &sme 200 hrs ng ) caliberate and adjust injectors and test report to be rendered. 158 1001 nmain engine ( qty 02 ) , nmake cummins, model kta 38m2 marine propulsion engine, power 1350bhp, 19500rpm, sl no port ( 25344299 ) , stbd ( 25344298 ) , running hours pme 200 hrs &sme 200 hrs nh ) remove and clean fresh water cooler .carry out pressure testing.renew gasket & o rings 159 1001 nmain engine ( qty 02 ) , nmake cummins, model kta 38m2 marine propulsion engine, power 1350bhp, 19500rpm, sl no port ( 25344299 ) , stbd ( 25344298 ) , running hours pme 200 hrs &sme 200 hrs nj ) air starter and air starting mechanism need to be overhauled 160 1001 nmain engine ( qty 02 ) , nmake cummins, model kta 38m2 marine propulsion engine, power 1350bhp, 19500rpm, sl no port ( 25344299 ) , stbd ( 25344298 ) , running hours pme 200 hrs &sme 200 hrs nk ) expansion tank and connecting piping to clean internally and repair if required. 161 1001 nmain engine ( qty 02 ) , nmake cummins, model kta 38m2 marine propulsion engine, power 1350bhp, 19500rpm, sl no port ( 25344299 ) , stbd ( 25344298 ) , running hours pme 200 hrs &sme 200 hrs nm ) gear box lub oil to be renewed 162 1001 nmain engine ( qty 02 ) , nmake cummins, model kta 38m2 marine propulsion engine, power 1350bhp, 19500rpm, sl no port ( 25344299 ) , stbd ( 25344298 ) , running hours pme 200 hrs &sme 200 hrs nn ) damaged fly wheel gear teeth of both main engine to repaired 163 1001 nmain engine ( qty 02 ) , nmake cummins, model kta 38m2 marine propulsion engine, power 1350bhp, 19500rpm, sl no port ( 25344299 ) , stbd ( 25344298 ) , running hours pme 200 hrs &sme 200 hrs n ( p ) renew fly wheel if repair is not feasible 164 1001 nmain engine ( qty 02 ) , nmake cummins, model kta 38m2 marine propulsion engine, power 1350bhp, 19500rpm, sl no port ( 25344299 ) , stbd ( 25344298 ) , running hours pme 200 hrs &sme 200 hrs nq ) remove and clean lub oil cooler carry out pressure testing.renew gasket & o rings 165 1001 nmain engine ( qty 02 ) , nmake cummins, model kta 38m2 marine propulsion engine, power 1350bhp, 19500rpm, sl no port ( 25344299 ) , stbd ( 25344298 ) , running hours pme 200 hrs &sme 200 hrs nr ) replace all rubber hoses and durret 166 1001 nmain engine ( qty 02 ) , nmake cummins, model kta 38m2 marine propulsion engine, power 1350bhp, 19500rpm, sl no port ( 25344299 ) , stbd ( 25344298 ) , running hours pme 200 hrs &sme 200 hrs ns ) both engine sea water pump to be overhauled and defective part to be renew 167 1001 nmain engine ( qty 02 ) , nmake cummins, model kta 38m2 marine propulsion engine, power 1350bhp, 19500rpm, sl no port ( 25344299 ) , stbd ( 25344298 ) , running hours pme 200 hrs &sme 200 hrs nt ) air starting mechanism mositure absorber body leaking. to be repaired 168 1001 nmain engine ( qty 02 ) , nmake cummins, model kta 38m2 marine propulsion engine, power 1350bhp, 19500rpm, sl no port ( 25344299 ) , stbd ( 25344298 ) , running hours pme 200 hrs &sme 200 hrs nu ) post completion of routine, engine to be proved for satisfactory performance nnote: routine to be carried out by oem only and all the calibration certificate and test report to be rendered. 169 1002 nemergency generator ( qty 01 ) , nmake kiorloskar &crompton greaves ac generator, thane, model brd.0.9c54.7, sl no: 62r6.5 / 41 running hours 40 hrs. 170 1002 nemergency generator ( qty 01 ) , make kiorloskar &crompton greaves ac generator, thane, model brd.0.9c54.7, sl no: 62r6.5 / 41 running hours 40 hrs. n ( a ) carry out adjustment of injectors & valves. 171 1002 nemergency generator ( qty 01 ) , nmake kiorloskar &crompton greaves ac generator, thane, model brd.0.9c54.7, sl no: 62r6.5 / 41 running hours 40 hrs. n ( b ) drive belt need to be changed. 172 1002 nemergency generator ( qty 01 ) , nmake kiorloskar &crompton greaves ac generator, thane, model brd.0.9c54.7, sl no: 62r6.5 / 41 running hours 40 hrs. n ( c ) replace rocker cover gaskets. 173 1002 nemergency generator ( qty 01 ) , nmake kiorloskar &crompton greaves ac generator, thane, model brd.0.9c54.7, sl no: 62r6.5 / 41 running hours 40 hrs. nd ) change engine oil. ( oil will be supplied by navy ) 174 1002 nemergency generator ( qty 01 ) , make kiorloskar &crompton greaves ac generator, thane, model brd.0.9c54.7, sl no: 62r6.5 / 41 running hours 40 hrs. ne ) change air cleaner element. 175 1002 nemergency generator ( qty 01 ) , make kiorloskar &crompton greaves ac generator, thane, model brd.0.9c54.7, sl no: 62r6.5 / 41 running hours 40 hrs. nf ) change fuel filter. 176 1002 nemergency generator ( qty 01 ) , make kiorloskar &crompton greaves ac generator, thane, model brd.0.9c54.7, sl no: 62r6.5 / 41 running hours 40 hrs. ng ) renew coolant inhibitor with zinc plugs. 177 1002 nemergency generator ( qty 01 ) , make kiorloskar &crompton greaves ac generator, thane, model brd.0.9c54.7, sl no: 62r6.5 / 41 running hours 40 hrs. nh ) renew engine oil filter. 178 1002 nemergency generator ( qty 01 ) , make kiorloskar &crompton greaves ac generator, thane, model brd.0.9c54.7, sl no: 62r6.5 / 41 running hours 40 hrs. nj ) renew by pass filter. 179 1002 nemergency generator ( qty 01 ) , make kiorloskar &crompton greaves ac generator, thane, model brd.0.9c54.7, sl no: 62r6.5 / 41 running hours 40 hrs. nk ) post completion of routine, engine to be proved for satisfactory performance 180 1002 nemergency generator ( qty 01 ) , make kiorloskar &crompton greaves ac generator, thane, model brd.0.9c54.7, sl no: 62r6.5 / 41 running hours 40 hrs. nl ) remove and clean lub oil cooler carry out pressure testing. renew gasket & o rings 181 1002 nemergency generator ( qty 01 ) , make kiorloskar &crompton greaves ac generator, thane, model brd.0.9c54.7, sl no: 62r6.5 / 41 running hours 40 hrs. nm ) replace all rubber hoses and durret nnote: routine to be carried out by oem only. 182 1003 nhp air compressor ( qty 02 ) , make ingersoll rand, u.d.marketing pvt ltd.kolkata, type electric driven, high pressure , model 7t4x5, capacity 12cu.m / hr@30 bar, sl no 9054135 ( motor driven ) , 9054134 ( diesel driven ) 183 1003 nhp air compressor ( qty 02 ) , make ingersoll rand, u.d.marketing pvt ltd.kolkata, type electric driven, high pressure , model 7t4x5, capacity 12cu.m / hr@30 bar, sl no 9054135 ( motor driven ) , 9054134 ( diesel driven ) n ( a ) lub oil sump to be drained, cleaned &new oil to be charged ( lub oil will be provided by the department ) 184 1003 nhp air compressor ( qty 02 ) , make ingersoll rand, u.d.marketing pvt ltd.kolkata, type electric driven, high pressure , model 7t4x5, capacity 12cu.m / hr@30 bar, sl no 9054135 ( motor driven ) , 9054134 ( diesel driven ) n ( b ) renew air inlet filter element. 185 1003 nhp air compressor ( qty 02 ) , make ingersoll rand, u.d.marketing pvt ltd.kolkata, type electric driven, high pressure , model 7t4x5, capacity 12cu.m / hr@30 bar, sl no 9054135 ( motor driven ) , 9054134 ( diesel driven ) n ( c ) sump stainers / filter to be cleaned & fitback 186 1003 nhp air compressor ( qty 02 ) , make ingersoll rand, u.d.marketing pvt ltd.kolkata, type electric driven, high pressure , model 7t4x5, capacity 12cu.m / hr@30 bar, sl no 9054135 ( motor driven ) , 9054134 ( diesel driven ) n ( d ) sump stainers / filter to renew , if strainer perished 187 1003 nhp air compressor ( qty 02 ) , make ingersoll rand, u.d.marketing pvt ltd.kolkata, type electric driven, high pressure , model 7t4x5, capacity 12cu.m / hr@30 bar, sl no 9054135 ( motor driven ) , 9054134 ( diesel driven ) n ( e ) instumentation gauges pipes with suitable end fittings to be renewed mat:cuni dia:1 / 4 188 1003 nhp air compressor ( qty 02 ) , make ingersoll rand, u.d.marketing pvt ltd.kolkata, type electric driven, high pressure , model 7t4x5, capacity 12cu.m / hr@30 bar, sl no 9054135 ( motor driven ) , 9054134 ( diesel driven ) n ( f ) pressure switches to be calibrated and proven for correct operation. 189 1003 nhp air compressor ( qty 02 ) , make ingersoll rand, u.d.marketing pvt ltd.kolkata, type electric driven, high pressure , model 7t4x5, capacity 12cu.m / hr@30 bar, sl no 9054135 ( motor driven ) , 9054134 ( diesel driven ) n ( g ) oil / water moisture separator of compressors to be renewed 190 1003 nhp air compressor ( qty 02 ) , make ingersoll rand, u.d.marketing pvt ltd.kolkata, type electric driven, high pressure , model 7t4x5, capacity 12cu.m / hr@30 bar, sl no 9054135 ( motor driven ) , 9054134 ( diesel driven ) n ( h ) chemical cleaning & pressure testing of air bottles to be carried out.capacity 375ltrs, tp 49bar 191 1003 nhp air compressor ( qty 02 ) , make ingersoll rand, u.d.marketing pvt ltd.kolkata, type electric driven, high pressure , model 7t4x5, capacity 12cu.m / hr@30 bar, sl no 9054135 ( motor driven ) , 9054134 ( diesel driven ) n ( j ) relief valves on air bottles to be set at 45 bar. 192 1003 nhp air compressor ( qty 02 ) , make ingersoll rand, u.d.marketing pvt ltd.kolkata, type electric driven, high pressure , model 7t4x5, capacity 12cu.m / hr@30 bar, sl no 9054135 ( motor driven ) , 9054134 ( diesel driven ) n ( k ) renew air system cocks.mat ss, dia 20mm 193 1003 nhp air compressor ( qty 02 ) , make ingersoll rand, u.d.marketing pvt ltd.kolkata, type electric driven, high pressure , model 7t4x5, capacity 12cu.m / hr@30 bar, sl no 9054135 ( motor driven ) , 9054134 ( diesel driven ) n ( l ) drive belts of compressor to be changed. 194 1003 nhp air compressor ( qty 02 ) , make ingersoll rand, u.d.marketing pvt ltd.kolkata, type electric driven, high pressure , model 7t4x5, capacity 12cu.m / hr@30 bar, sl no 9054135 ( motor driven ) , 9054134 ( diesel driven ) n ( m ) drive belt guard of compressor to be renewed. 195 1003 nhp air compressor ( qty 02 ) , make ingersoll rand, u.d.marketing pvt ltd.kolkata, type electric driven, high pressure , model 7t4x5, capacity 12cu.m / hr@30 bar, sl no 9054135 ( motor driven ) , 9054134 ( diesel driven ) nn ) top cover of compressor to be opened and inspection of piston and valves to be carried out 196 1003 nhp air compressor ( qty 02 ) , make ingersoll rand, u.d.marketing pvt ltd.kolkata, type electric driven, high pressure , model 7t4x5, capacity 12cu.m / hr@30 bar, sl no 9054135 ( motor driven ) , 9054134 ( diesel driven ) np ) replace top cover gaskets. 197 1003 nhp air compressor ( qty 02 ) , make ingersoll rand, u.d.marketing pvt ltd.kolkata, type electric driven, high pressure , model 7t4x5, capacity 12cu.m / hr@30 bar, sl no 9054135 ( motor driven ) , 9054134 ( diesel driven ) n ( q ) compressor to be proved for satisfactory perfomance. 198 1003 nhp air compressor ( qty 02 ) , make ingersoll rand, u.d.marketing pvt ltd.kolkata, type electric driven, high pressure , model 7t4x5, capacity 12cu.m / hr@30 bar, sl no 9054135 ( motor driven ) , 9054134 ( diesel driven ) n ( r ) air cooled intercooler and after cooler to tubes to clean , deposits of oil , dirt or grease to removed 199 1003 nhp air compressor ( qty 02 ) , make ingersoll rand, u.d.marketing pvt ltd.kolkata, type electric driven, high pressure , model 7t4x5, capacity 12cu.m / hr@30 bar, sl no 9054135 ( motor driven ) , 9054134 ( diesel driven ) n ( s ) proper mounting of canopy to base frame with smooth opening and closing operation to ensure. the base frame and canopy to zinc sprayed fo rust inhibition, primer and final paint to applied. canopy sealing gasket xlpe to renewed. 200 1004 ndiesel generator ( koel & crompton ) ( qty 02 ) , make koel, model 6sl9088ta1, output 176bhp@1500rpm, sl no: f6.3002 / 0900004 ( port ) , f6.3002 / 0900005 ( stbd ) running hours pdg 1200 hrs sdg 1000 hrs ( 1500 hrly routine to be carried out ) 201 1004 ndiesel generator ( koel & crompton ) ( qty 02 ) , make koel, model 6sl9088ta1, output 176bhp@1500rpm, sl no: f6.3002 / 0900004 ( port ) , f6.3002 / 0900005 ( stbd ) running hours pdg 1200 hrs sdg 1000 hrs ( 1500 hrly routine to be carried out ) n ( a ) carry out pr testing, adjustment of injectors & valves and test report to be rendered. 202 1004 ndiesel generator ( koel & crompton ) ( qty 02 ) , make koel, model 6sl9088ta1, output 176bhp@1500rpm, sl no: f6.3002 / 0900004 ( port ) , f6.3002 / 0900005 ( stbd ) running hours pdg 1200 hrs sdg 1000 hrs ( 1500 hrly routine to be carried out ) n ( b ) replace rocker cover gaskets. 203 1004 ndiesel generator ( koel & crompton ) ( qty 02 ) , make koel, model 6sl9088ta1, output 176bhp@1500rpm, sl no: f6.3002 / 0900004 ( port ) , f6.3002 / 0900005 ( stbd ) running hours pdg 1200 hrs sdg 1000 hrs ( 1500 hrly routine to be carried out ) nc ) change engine oil. ( oil to provided by navy ) 204 1004 ndiesel generator ( koel & crompton ) ( qty 02 ) , make koel, model 6sl9088ta1, output 176bhp@1500rpm, sl no: f6.3002 / 0900004 ( port ) , f6.3002 / 0900005 ( stbd ) running hours pdg 1200 hrs sdg 1000 hrs ( 1500 hrly routine to be carried out ) n ( d ) overhaul sea water pump.prove the pump for satisfactory performance and defective part to be renewed. 205 1004 ndiesel generator ( koel & crompton ) ( qty 02 ) , make koel, model 6sl9088ta1, output 176bhp@1500rpm, sl no: f6.3002 / 0900004 ( port ) , f6.3002 / 0900005 ( stbd ) running hours pdg 1200 hrs sdg 1000 hrs ( 1500 hrly routine to be carried out ) ne ) clean expansion tank internally, repair expansion tank and connecting piping if required. replace coolant ( coolant to be provided by firm ) 206 1004 ndiesel generator ( koel & crompton ) ( qty 02 ) , make koel, model 6sl9088ta1, output 176bhp@1500rpm, sl no: f6.3002 / 0900004 ( port ) , f6.3002 / 0900005 ( stbd ) running hours pdg 1200 hrs sdg 1000 hrs ( 1500 hrly routine to be carried out ) n ( f ) remove & chemical clean lub oil cooler & carry out pressure testing.renew gasket & o rings.zing plugs to be renewed 207 1004 ndiesel generator ( koel & crompton ) ( qty 02 ) , make koel, model 6sl9088ta1, output 176bhp@1500rpm, sl no: f6.3002 / 0900004 ( port ) , f6.3002 / 0900005 ( stbd ) running hours pdg 1200 hrs sdg 1000 hrs ( 1500 hrly routine to be carried out ) n ( g ) remove & chemical clean fresh water cooler & carry out pressure testing.renew gasket & o rings. zing plugs to be renewed 208 1004 ndiesel generator ( koel & crompton ) ( qty 02 ) , make koel, model 6sl9088ta1, output 176bhp@1500rpm, sl no: f6.3002 / 0900004 ( port ) , f6.3002 / 0900005 ( stbd ) running hours pdg 1200 hrs sdg 1000 hrs ( 1500 hrly routine to be carried out ) n ( h ) change heat exchanger zinc plugs. 209 1004 ndiesel generator ( koel & crompton ) ( qty 02 ) , make koel, model 6sl9088ta1, output 176bhp@1500rpm, sl no: f6.3002 / 0900004 ( port ) , f6.3002 / 0900005 ( stbd ) running hours pdg 1200 hrs sdg 1000 hrs ( 1500 hrly routine to be carried out ) n ( j ) check thottle linkage, lubricate ball joints of the throttle linkage of governor. 210 1004 ndiesel generator ( koel & crompton ) ( qty 02 ) , make koel, model 6sl9088ta1, output 176bhp@1500rpm, sl no: f6.3002 / 0900004 ( port ) , f6.3002 / 0900005 ( stbd ) running hours pdg 1200 hrs sdg 1000 hrs ( 1500 hrly routine to be carried out ) n ( k ) all rubber durrets & hoses to be replaced. 211 1004 ndiesel generator ( koel & crompton ) ( qty 02 ) , make koel, model 6sl9088ta1, output 176bhp@1500rpm, sl no: f6.3002 / 0900004 ( port ) , f6.3002 / 0900005 ( stbd ) running hours pdg 1200 hrs sdg 1000 hrs ( 1500 hrly routine to be carried out ) n ( l ) change fuel filter 212 1004 ndiesel generator ( koel & crompton ) ( qty 02 ) , make koel, model 6sl9088ta1, output 176bhp@1500rpm, sl no: f6.3002 / 0900004 ( port ) , f6.3002 / 0900005 ( stbd ) running hours pdg 1200 hrs sdg 1000 hrs ( 1500 hrly routine to be carried out ) n ( m ) change air cleaner element. 213 1004 ndiesel generator ( koel & crompton ) ( qty 02 ) , make koel, model 6sl9088ta1, output 176bhp@1500rpm, sl no: f6.3002 / 0900004 ( port ) , f6.3002 / 0900005 ( stbd ) running hours pdg 1200 hrs sdg 1000 hrs ( 1500 hrly routine to be carried out ) n ( n ) caliberation of fip & governor assembly to be carried out.report of the same to be rendered 214 1004 ndiesel generator ( koel & crompton ) ( qty 02 ) , make koel, model 6sl9088ta1, output 176bhp@1500rpm, sl no: f6.3002 / 0900004 ( port ) , f6.3002 / 0900005 ( stbd ) running hours pdg 1200 hrs sdg 1000 hrs ( 1500 hrly routine to be carried out ) n ( p ) rectify if any defect observed in fip & governor assembly 215 1004 ndiesel generator ( koel & crompton ) ( qty 02 ) , make koel, model 6sl9088ta1, output 176bhp@1500rpm, sl no: f6.3002 / 0900004 ( port ) , f6.3002 / 0900005 ( stbd ) running hours pdg 1200 hrs sdg 1000 hrs ( 1500 hrly routine to be carried out ) n ( q ) overhauling of electric starter to be done nnote: 1500 hrly routine of dg to be undertaken by oem 216 1005 nfuel oiltransfer pump ( qty 02 ) , make: royson engineers pvt ltd, kolkata , model: rgp 1 mt , capacity: 2 cu.m / hr@20mwc, sl no: b1403 09. 217 1005 nfuel oiltransfer pump ( qty 02 ) , make: royson engineers pvt ltd, kolkata , model: rgp 1 mt , capacity: 2 cu.m / hr@20mwc, sl no: b1403 09. n ( a ) carry out overhauling of pumps, renew bearing &shaft seal. 218 1005 nfuel oiltransfer pump ( qty 02 ) , make: royson engineers pvt ltd, kolkata , model: rgp 1 mt , capacity: 2 cu.m / hr@20mwc, sl no: b1403 09. n ( b ) suction &discharge presure gauges to be renewed.range 30 0 &0 05bar 219 1005 nfuel oiltransfer pump ( qty 02 ) , make: royson engineers pvt ltd, kolkata , model: rgp 1 mt , capacity: 2 cu.m / hr@20mwc, sl no: b1403 09. n ( c ) renew needle valve.mat ss 220 1005 nfuel oiltransfer pump ( qty 02 ) , make: royson engineers pvt ltd, kolkata , model: rgp 1 mt , capacity: 2 cu.m / hr@20mwc, sl no: b1403 09. n ( d ) carry out alignment of pump with motor &prove for satisfactory perfomance. 221 1006 nfuel oil centrifuge ( qty 01 ) , make: alfa lavel india ltd, pune, capacity 1150lph@disc pr 1.5 kg / cm2, model mab103, sl no: 4176151 2008 222 1006 nfuel oil centrifuge ( qty 01 ) , make: alfa lavel india ltd, pune, capacity 1150lph@disc pr 1.5 kg / cm2, model mab103, sl no: 4176151 2008 n ( a ) centrifuge bowl assembly to be dismantled.all separator disc plates to be removed cleaned &fitted back.renew disc plates if perished. 223 1006 nfuel oil centrifuge ( qty 01 ) , make: alfa lavel india ltd, pune, capacity 1150lph@disc pr 1.5 kg / cm2, model mab103, sl no: 4176151 2008 n ( b ) check the condition of gravity disc.renew gravity disc, if required. 224 1006 nfuel oil centrifuge ( qty 01 ) , make: alfa lavel india ltd, pune, capacity 1150lph@disc pr 1.5 kg / cm2, model mab103, sl no: 4176151 2008 n ( c ) drive shaft friction pads to be renewed 225 1006 nfuel oil centrifuge ( qty 01 ) , make: alfa lavel india ltd, pune, capacity 1150lph@disc pr 1.5 kg / cm2, model mab103, sl no: 4176151 2008 n ( d ) suction & discharge presure gauges to be renewed range:30 0 & 0 8. 226 1006 nfuel oil centrifuge ( qty 01 ) , make: alfa lavel india ltd, pune, capacity 1150lph@disc pr 1.5 kg / cm2, model mab103, sl no: 4176151 2008 n ( e ) 02 pr.gauges of 0 6 bar, 02 copper pipes with suitable end fittings to be renewed.mat:cuni dia:1 / 4. 227 1006 nfuel oil centrifuge ( qty 01 ) , make: alfa lavel india ltd, pune, capacity 1150lph@disc pr 1.5 kg / cm2, model mab103, sl no: 4176151 2008 n ( f ) condition of sv mounts be checked, if found defective to be renewed. 228 1006 nfuel oil centrifuge ( qty 01 ) , make: alfa lavel india ltd, pune, capacity 1150lph@disc pr 1.5 kg / cm2, model mab103, sl no: 4176151 2008 n ( g ) centrifuge to be proved for satisfactory perfomance post work completion. 229 1007 nfuel oil cargo pump ( qty 02 ) , make: best & crompton engg.ltd, chennai, capacity 100cu.m@30 mwc, sl no: w0050110 ( no.1 ) , w0047610 ( no.2 ) 230 1007 nfuel oil cargo pump ( qty 02 ) , make: best & crompton engg.ltd, chennai, capacity 100cu.m@30 mwc, sl no: w0050110 ( no.1 ) , w0047610 ( no.2 ) n ( a ) carry out overhauling of pumps, renew bearing &shaft seal. 231 1007 nfuel oil cargo pump ( qty 02 ) , make: best & crompton engg.ltd, chennai, capacity 100cu.m@30 mwc, sl no: w0050110 ( no.1 ) , w0047610 ( no.2 ) n ( b ) suction &discharge presure gauges to be renewed.range 30 0 &0 100psi. 232 1007 nfuel oil cargo pump ( qty 02 ) , make: best & crompton engg.ltd, chennai, capacity 100cu.m@30 mwc, sl no: w0050110 ( no.1 ) , w0047610 ( no.2 ) n ( c ) renew needle valve.mat ss 233 1007 nfuel oil cargo pump ( qty 02 ) , make: best & crompton engg.ltd, chennai, capacity 100cu.m@30 mwc, sl no: w0050110 ( no.1 ) , w0047610 ( no.2 ) n ( d ) carry out alignment of pump with motor &prove for satisfactory perfomance. 234 1008 nlub oil transfer pump ( qty 01 ) , make: royson engineers pvt ltd, kolkata , model: rgp 1 mt, capacity: 1 cu.m / hr@5kg / cm2.sl. no b1396 02 235 1008 nlub oil transfer pump ( qty 01 ) , make: royson engineers pvt ltd, kolkata , model: rgp 1 mt, capacity: 1 cu.m / hr@5kg / cm2.sl. no b1396 02 n ( a ) overhauling of pumps includes repair / renewal of weardown parts ( shaft, mechanical seals, impeller, gaskets, bearings ) and fitted back. 236 1008 nlub oil transfer pump ( qty 01 ) , make: royson engineers pvt ltd, kolkata , model: rgp 1 mt, capacity: 1 cu.m / hr@5kg / cm2.sl. no b1396 02 n ( b ) suction & discharge presure gauges to be renewed range:30 0 & 0 5bar. 237 1008 nlub oil transfer pump ( qty 01 ) , make: royson engineers pvt ltd, kolkata , model: rgp 1 mt, capacity: 1 cu.m / hr@5kg / cm2.sl. no b1396 02 n ( c ) renew needle valve.mat ss 238 1008 nlub oil transfer pump ( qty 01 ) , make: royson engineers pvt ltd, kolkata , model: rgp 1 mt, capacity: 1 cu.m / hr@5kg / cm2.sl. no b1396 02 n ( d ) carry out alignment of pump with motor &prove for satisfactory perfomance 239 1009 noily bilge water separator ( qty 01 ) , make: victor marine ltd, uk, type: cs500, capacity: 0.5 cu.m / hr@3.45 bar, suction head: 0.6bar at separator inlet, disc head: 3.45bar, sl no: 00358. 240 1009 noily bilge water separator ( qty 01 ) , make: victor marine ltd, uk, type: cs500, capacity: 0.5 cu.m / hr@3.45 bar, suction head: 0.6bar at separator inlet, disc head: 3.45bar, sl no: 00358. n ( a ) proximity sensors to be calibtrated &replace if required. 241 1009 noily bilge water separator ( qty 01 ) , make: victor marine ltd, uk, type: cs500, capacity: 0.5 cu.m / hr@3.45 bar, suction head: 0.6bar at separator inlet, disc head: 3.45bar, sl no: 00358. n ( b ) calibration of 3 / 2 way pneumatic valve. 242 1009 noily bilge water separator ( qty 01 ) , make: victor marine ltd, uk, type: cs500, capacity: 0.5 cu.m / hr@3.45 bar, suction head: 0.6bar at separator inlet, disc head: 3.45bar, sl no: 00358. n ( c ) renewal of 6mm copper pipe. 243 1009 noily bilge water separator ( qty 01 ) , make: victor marine ltd, uk, type: cs500, capacity: 0.5 cu.m / hr@3.45 bar, suction head: 0.6bar at separator inlet, disc head: 3.45bar, sl no: 00358. n ( d ) primary & secondry cell cleaning. 244 1009 noily bilge water separator ( qty 01 ) , make: victor marine ltd, uk, type: cs500, capacity: 0.5 cu.m / hr@3.45 bar, suction head: 0.6bar at separator inlet, disc head: 3.45bar, sl no: 00358. n ( e ) primary & secondery stage filter to be replaced. 245 1009 noily bilge water separator ( qty 01 ) , make: victor marine ltd, uk, type: cs500, capacity: 0.5 cu.m / hr@3.45 bar, suction head: 0.6bar at separator inlet, disc head: 3.45bar, sl no: 00358. n ( f ) overhauling of screw pump. 246 1009 noily bilge water separator ( qty 01 ) , make: victor marine ltd, uk, type: cs500, capacity: 0.5 cu.m / hr@3.45 bar, suction head: 0.6bar at separator inlet, disc head: 3.45bar, sl no: 00358. n ( g ) caliberation of puri meter. 247 1009 noily bilge water separator ( qty 01 ) , make: victor marine ltd, uk, type: cs500, capacity: 0.5 cu.m / hr@3.45 bar, suction head: 0.6bar at separator inlet, disc head: 3.45bar, sl no: 00358. n ( h ) perfomances trials for satisfactory perfomance. 248 1010 ndirty oil pump ( qty 01 ) , make , model: royson engineers pvt ltd, kolkata , model: rgp 1 mt, capacity: 1 cu.m / hr@2kg / cm2, sl no: b1400 02. 249 1010 ndirty oil pump ( qty 01 ) , make , model: royson engineers pvt ltd, kolkata , model: rgp 1 mt, capacity: 1 cu.m / hr@2kg / cm2, sl no: b1400 02. n ( a ) carry out overhauling of pump 250 1010 ndirty oil pump ( qty 01 ) , make , model: royson engineers pvt ltd, kolkata , model: rgp 1 mt, capacity: 1 cu.m / hr@2kg / cm2, sl no: b1400 02. n ( b ) suction &discharge presure gauges to be renewed.range 30 0 &0 05bar 251 1010 ndirty oil pump ( qty 01 ) , make , model: royson engineers pvt ltd, kolkata , model: rgp 1 mt, capacity: 1 cu.m / hr@2kg / cm2, sl no: b1400 02. n ( c ) renew needle valve.mat ss 252 1010 ndirty oil pump ( qty 01 ) , make , model: royson engineers pvt ltd, kolkata , model: rgp 1 mt, capacity: 1 cu.m / hr@2kg / cm2, sl no: b1400 02. n ( d ) renewal of bearings &shaft seal. 253 1010 ndirty oil pump ( qty 01 ) , make , model: royson engineers pvt ltd, kolkata , model: rgp 1 mt, capacity: 1 cu.m / hr@2kg / cm2, sl no: b1400 02. n ( e ) carry out alignment of pump with motor &prove for satisfactory perfomance. 254 1011 nbilge and ballast pump ( qty 04 ) , make: be pump, model: sh 65 160mn1 gds2 316, type: self priming, centrifugal, capacity: 35cu.m / hr@30kg / sq.cm, sl no: 357815 ( no.1 ) , 357814 ( no.2 ) , 357813 ( no.3 ) , 357812 ( no.4 255 1011 nbilge and ballast pump ( qty 04 ) , make: be pump, model: sh 65 160mn1 gds2 316, type: self priming, centrifugal, capacity: 35cu.m / hr@30kg / sq.cm, sl no: 357815 ( no.1 ) , 357814 ( no.2 ) , 357813 ( no.3 ) , 357812 ( no.4 n ( a ) carry out overhauling of pumps, renew parts if required. 256 1011 nbilge and ballast pump ( qty 04 ) , make: be pump, model: sh 65 160mn1 gds2 316, type: self priming, centrifugal, capacity: 35cu.m / hr@30kg / sq.cm, sl no: 357815 ( no.1 ) , 357814 ( no.2 ) , 357813 ( no.3 ) , 357812 ( no.4 n ( b ) instumentation gauges pipes with suitable end fittings to be renewed .cuni dia:1 / 4 257 1011 nbilge and ballast pump ( qty 04 ) , make: be pump, model: sh 65 160mn1 gds2 316, type: self priming, centrifugal, capacity: 35cu.m / hr@30kg / sq.cm, sl no: 357815 ( no.1 ) , 357814 ( no.2 ) , 357813 ( no.3 ) , 357812 ( no.4 n ( c ) renew needle valve. mat 1 / 4 258 1011 nbilge and ballast pump ( qty 04 ) , make: be pump, model: sh 65 160mn1 gds2 316, type: self priming, centrifugal, capacity: 35cu.m / hr@30kg / sq.cm, sl no: 357815 ( no.1 ) , 357814 ( no.2 ) , 357813 ( no.3 ) , 357812 ( no.4 n ( d ) carryout alignment of pump with motor & prove for satisfactory perfomance. 259 1011 nbilge and ballast pump ( qty 04 ) , make: be pump, model: sh 65 160mn1 gds2 316, type: self priming, centrifugal, capacity: 35cu.m / hr@30kg / sq.cm, sl no: 357815 ( no.1 ) , 357814 ( no.2 ) , 357813 ( no.3 ) , 357812 ( no.4 n ( e ) suction & discharge pressure gauges to be renewed.range 0 120psi & 30 30psi. 260 1011 nbilge and ballast pump ( qty 04 ) , make: be pump, model: sh 65 160mn1 gds2 316, type: self priming, centrifugal, capacity: 35cu.m / hr@30kg / sq.cm, sl no: 357815 ( no.1 ) , 357814 ( no.2 ) , 357813 ( no.3 ) , 357812 ( no.4 n ( f ) renew jaw coupling & rubber coupling between pump & motor. 261 1011 nbilge and ballast pump ( qty 04 ) , make: be pump, model: sh 65 160mn1 gds2 316, type: self priming, centrifugal, capacity: 35cu.m / hr@30kg / sq.cm, sl no: 357815 ( no.1 ) , 357814 ( no.2 ) , 357813 ( no.3 ) , 357812 ( no.4 n ( g ) rectify leakages in self priming unit, renew flexible hoses if required. 262 1012 nfresh water cargo pump, make: be pump, model: ma 843kks dgs2 316 ms 3, type: self priming, centrifugal, capacity: 40cu.m / hr@30kg / sq.cm, sl no: 357811. 263 1012 nfresh water cargo pump, make: be pump, model: ma 843kks dgs2 316 ms 3, type: self priming, centrifugal, capacity: 40cu.m / hr@30kg / sq.cm, sl no: 357811. n ( a ) carry out overhauling of pumps, renew parts if required. 264 1012 nfresh water cargo pump, make: be pump, model: ma 843kks dgs2 316 ms 3, type: self priming, centrifugal, capacity: 40cu.m / hr@30kg / sq.cm, sl no: 357811. n ( b ) instumentation gauges pipes with suitable end fittings to be renewed .cuni dia:1 / 4 265 1012 nfresh water cargo pump, make: be pump, model: ma 843kks dgs2 316 ms 3, type: self priming, centrifugal, capacity: 40cu.m / hr@30kg / sq.cm, sl no: 357811. n ( c ) renew needle valve. mat 1 / 4 266 1012 nfresh water cargo pump, make: be pump, model: ma 843kks dgs2 316 ms 3, type: self priming, centrifugal, capacity: 40cu.m / hr@30kg / sq.cm, sl no: 357811. n ( d ) carryout alignment of pump with motor & prove for satisfactory perfomance. 267 1012 nfresh water cargo pump, make: be pump, model: ma 843kks dgs2 316 ms 3, type: self priming, centrifugal, capacity: 40cu.m / hr@30kg / sq.cm, sl no: 357811. n ( e ) suction & discharge pressure gauges to be renewed.range 268 1012 nfresh water cargo pump, make: be pump, model: ma 843kks dgs2 316 ms 3, type: self priming, centrifugal, capacity: 40cu.m / hr@30kg / sq.cm, sl no: 357811. n ( f ) renew jaw coupling & rubber coupling between pump & motor. 269 1013 nfuel oil / avcat stripping pump, make: royson engineers pvt ltd, kolkata , model: rgp 1 mt, capacity: 2cu.m / hr@20mwc, sl no: b 1399 09. 270 1013 nfuel oil / avcat stripping pump, make: royson engineers pvt ltd, kolkata , model: rgp 1 mt, capacity: 2cu.m / hr@20mwc, sl no: b 1399 09. n ( a ) pumps to be overhauled .renew wear down parts if required. 271 1013 nfuel oil / avcat stripping pump, make: royson engineers pvt ltd, kolkata , model: rgp 1 mt, capacity: 2cu.m / hr@20mwc, sl no: b 1399 09. n ( b ) suction & discharge pressure gauges to be renewed.range ( 1 to 1kg / sq.cm ) & 0 10kg / sq cm 272 1013 nfuel oil / avcat stripping pump, make: royson engineers pvt ltd, kolkata , model: rgp 1 mt, capacity: 2cu.m / hr@20mwc, sl no: b 1399 09. n ( c ) renew needle valve.mat:ss dia 1 / 4 273 1013 nfuel oil / avcat stripping pump, make: royson engineers pvt ltd, kolkata , model: rgp 1 mt, capacity: 2cu.m / hr@20mwc, sl no: b 1399 09. n ( d ) carry out alignment of pump with motor & prove for satisfactory perfomance. 274 1014 nvalve to be overhauled make vijoli, type screw down, overhauling includes renewal of wear down parts ( spindle, disc ) , mat gm 275 1014 nvalve to be overhauled make vijoli, type screw down, overhauling includes renewal of wear down parts ( spindle, disc ) , mat gm n ( a ) dia 300 mm 276 1014 nvalve to be overhauled make vijoli, type screw down, overhauling includes renewal of wear down parts ( spindle, disc ) , mat gm n ( b ) dia 150 mm 277 1014 nvalve to be overhauled make vijoli, type screw down, overhauling includes renewal of wear down parts ( spindle, disc ) , mat gm n ( c ) dia 125 mm 278 1014 nvalve to be overhauled make vijoli, type screw down, overhauling includes renewal of wear down parts ( spindle, disc ) , mat gm n ( d ) dia 100 mm 279 1014 nvalve to be overhauled make vijoli, type screw down, overhauling includes renewal of wear down parts ( spindle, disc ) , mat gm n ( e ) dia 80 mm 280 1014 nvalve to be overhauled make vijoli, type screw down, overhauling includes renewal of wear down parts ( spindle, disc ) , mat gm n ( f ) dia 40mm 281 1014 nvalve to be overhauled make vijoli, type screw down, overhauling includes renewal of wear down parts ( spindle, disc ) , mat gm n ( g ) dia 20mm 282 1014 nvalve to be overhauled make vijoli, type screw down, overhauling includes renewal of wear down parts ( spindle, disc ) , mat gm n ( h ) dia 32 mm 283 1014 nvalve to be overhauled make vijoli, type screw down, overhauling includes renewal of wear down parts ( spindle, disc ) , mat gm n ( j ) relief valves ( 100mm ) 284 1015 nbilge collecting pump, make: royson engineers pvt ltd, kolkata , model: rgp 1 mt, capacity: 2cu.m / hr@20mwc, sl no: b 1397 09. 285 1015 nbilge collecting pump, make: royson engineers pvt ltd, kolkata , model: rgp 1 mt, capacity: 2cu.m / hr@20mwc, sl no: b 1397 09. n ( a ) pumps to be overhauled .renew wear down parts if required. 286 1015 nbilge collecting pump, make: royson engineers pvt ltd, kolkata , model: rgp 1 mt, capacity: 2cu.m / hr@20mwc, sl no: b 1397 09. n ( b ) renew needle valve.mat:ss dia 1 / 4 287 1015 nbilge collecting pump, make: royson engineers pvt ltd, kolkata , model: rgp 1 mt, capacity: 2cu.m / hr@20mwc, sl no: b 1397 09. n ( c ) carry out alignment of pump with motor & prove for satisfactory perfo 288 1015 nbilge collecting pump, make: royson engineers pvt ltd, kolkata , model: rgp 1 mt, capacity: 2cu.m / hr@20mwc, sl no: b 1397 09. n ( d ) suction & discharge pressure gauges to be renewed.range ( 1 to 1kg / sq.cm ) & 0 10kg / sq cm 289 1016 neqpt / system: system pipes for chemical cleaning / renewal 290 1016 neqpt / system: system pipes for chemical cleaning / renewal n ( a ) dia 150 mm, fuel line pipes, test pr 05 bar 291 1016 neqpt / system: system pipes for chemical cleaning / renewal n ( b ) dia 100 mm, avcat line pipes, test pr 05 bar 292 1016 neqpt / system: system pipes for chemical cleaning / renewal n ( c ) dia 125 mm, sea water pipe line ( bilge / ballast / fire main ) , test pr 05 bar 293 1016 neqpt / system: system pipes for chemical cleaning / renewal n ( d ) dia 80mm, fresh water system pipes, test pr 05bar 294 1016 neqpt / system: system pipes for chemical cleaning / renewal n ( e ) dia 40 mm, fuel lines pipes, test pr. 2cu.m / hr 295 1016 neqpt / system: system pipes for chemical cleaning / renewal n ( f ) dia 32 mm, fuel line pipes, test pr. 5bar 296 1016 neqpt / system: system pipes for chemical cleaning / renewal n ( g ) dia 20mm, fuel line pipes, test pr. 4 bar 297 1016 neqpt / system: system pipes for chemical cleaning / renewal n ( ii ) following system pipes to be renewed along with flanges. 298 1016 neqpt / system: system pipes for chemical cleaning / renewal n ( ii ) following system pipes to be renewed along with flanges. n ( a ) sea water pipe lines ( 40 mm dia ) , port & stbd dg 299 1016 neqpt / system: system pipes for chemical cleaning / renewal n ( ii ) following system pipes to be renewed along with flanges. n ( b ) sea water pipe lines ( 20 mm dia ) , port & stbd dg 300 1017 nmiscellaneous: n ( a ) exhaust laging of both dg exhaust system to be renewed, dia 100mm 301 1017 nmiscellaneous: n ( b ) exhaust laging of dd compressor exhaust system to be renewed, dia 25mm 302 1017 nmiscellaneous: n ( c ) exhaust laging of both main engine exhaust system to be renewed, dia 200mm 303 1017 nmiscellaneous: n ( d ) manufacture of various adapters as per sample 304 1017 nmiscellaneous: n ( e ) fuel transfer hose to be provide. ( length 80mtr ) 305 1017 nmiscellaneous: n ( f ) mechanical cleaning of exhaust system of both dg ( dia 125mm ) 306 1017 nmiscellaneous: n ( h ) 2 kg + 4.5 kg co2 extinguisher to weighed 307 1017 nmiscellaneous: n ( i ) hose basket to be manufactured as per sample 308 1018 nco2 fire fighting sytem maker: shm ship care ( all procedures to be carried as mentioned below and replace defective parts if required ) 309 1018 nco2 fire fighting sytem maker: shm ship care ( all procedures to be carried as mentioned below and replace defective parts if required ) n ( a ) complete drenching system piping to be blown through using hp air to prove system free of blockages 310 1018 nco2 fire fighting sytem maker: shm ship care ( all procedures to be carried as mentioned below and replace defective parts if required ) n ( b ) admit lp air into ring main checking the system for leaks. ensure that all the discharge pipes and nozzles are clear. 311 1018 nco2 fire fighting sytem maker: shm ship care ( all procedures to be carried as mentioned below and replace defective parts if required ) nc ) caliberate pressure gauges fitted in the system. 312 1018 nco2 fire fighting sytem maker: shm ship care ( all procedures to be carried as mentioned below and replace defective parts if required ) n ( d ) co2 discharge nozzles to be opened, checked for chockages, cleaned and fitted back. carry out weighing of co 2 cylinders. 313 1018 nco2 fire fighting sytem maker: shm ship care ( all procedures to be carried as mentioned below and replace defective parts if required ) n ( e ) disconnect operating cables from cylinders. remove old grease and renew grease on all external fittings i.e. pulleys, pull handles, actuators, micro switches and cables and cables ( as applicable ) . ensure freedom of movement of gang release piston , and all cables, pulleys, cocks and valves. examine all nozzles and piping for any obstruction and clean, if required. reconnect cables on completion. 314 1018 nco2 fire fighting sytem maker: shm ship care ( all procedures to be carried as mentioned below and replace defective parts if required ) n ( f ) check the condition of flexible hoses.if required same to be renewed. ( pr 275bar ) 315 1018 nco2 fire fighting sytem maker: shm ship care ( all procedures to be carried as mentioned below and replace defective parts if required ) n ( g ) carry out functional checks of the sensors, alarms, solenoid and safety system. ensure that they are operational. replace / repair componets as required. 316 1018 nco2 fire fighting sytem maker: shm ship care ( all procedures to be carried as mentioned below and replace defective parts if required ) n ( h ) lamp checks of various indication in the control panel. replace if defective 317 1018 nco2 fire fighting sytem maker: shm ship care ( all procedures to be carried as mentioned below and replace defective parts if required ) n ( i ) check klaxon horn and strobe comes on 318 1018 nco2 fire fighting sytem maker: shm ship care ( all procedures to be carried as mentioned below and replace defective parts if required ) n ( k ) check hooter and fire detector 319 1018 nco2 fire fighting sytem maker: shm ship care ( all procedures to be carried as mentioned below and replace defective parts if required ) n ( l ) clean all contacts of relays and push buttons of the control panel. 320 1018 nco2 fire fighting sytem maker: shm ship care ( all procedures to be carried as mentioned below and replace defective parts if required ) n ( m ) carry out insulation and continuity check of wiring and control panel. nnote: the entire co2 system to be proved for functional checks without co2 321 1019 navcat pump, make best & crompton engg.ltd, chennai, capacity 40cu.m@30 kg / sq.cm, 322 1019 navcat pump, make best & crompton engg.ltd, chennai, capacity 40cu.m@30 kg / sq.cm, n ( a ) carry out oveerhauling of pumps, renew bearing &shaft seal. 323 1019 navcat pump, make best & crompton engg.ltd, chennai, capacity 40cu.m@30 kg / sq.cm, n ( b ) suction &discharge presure gauges to be renewed.range 30 0 &0 6bar. 324 1019 navcat pump, make best & crompton engg.ltd, chennai, capacity 40cu.m@30 kg / sq.cm, n ( c ) renew needle valve.mat ss 325 1019 navcat pump, make best & crompton engg.ltd, chennai, capacity 40cu.m@30 kg / sq.cm, n ( d ) carry out alignment of pump with motor &prove for satisfactory perfomance. 326 1020 nsteering system, make : m / s getha eng works, working pressure 104 bar, sl.no 6144 1 ( port ) , 6144 2 ( stbd ) 327 1020 nsteering system, make : m / s getha eng works, working pressure 104 bar, sl.no 6144 1 ( port ) , 6144 2 ( stbd ) n ( a ) change hydraulic filter elements ( `pump suction, return line, reserve line and emergency line filters ) . 328 1020 nsteering system, make : m / s getha eng works, working pressure 104 bar, sl.no 6144 1 ( port ) , 6144 2 ( stbd ) n ( b ) lubtricate power unit motor bearings ( grease xg 272 ) 329 1020 nsteering system, make : m / s getha eng works, working pressure 104 bar, sl.no 6144 1 ( port ) , 6144 2 ( stbd ) n ( c ) lubricate actuator bearings ( grease lg 280 / xg 279 ) 330 1020 nsteering system, make : m / s getha eng works, working pressure 104 bar, sl.no 6144 1 ( port ) , 6144 2 ( stbd ) n ( d ) hand pump to be operated and system to be checked with hand pump for operation, leakages in system to be rectified. 331 1020 nsteering system, make : m / s getha eng works, working pressure 104 bar, sl.no 6144 1 ( port ) , 6144 2 ( stbd ) n ( e ) visually check electric motor and cables. 332 1020 nsteering system, make : m / s getha eng works, working pressure 104 bar, sl.no 6144 1 ( port ) , 6144 2 ( stbd ) n ( f ) mechanical cleaning of propellers and rudders for sea growth during docking of the vessel. and preservation of propeeler using greese to be done during docking periods 333 1021 ndd compressor engine, make kirloskar oil engine, model taf1, sl. no 20.1222 / 1002005 n following work to be carried : 334 1021 ndd compressor engine, make kirloskar oil engine, model taf1, sl. no 20.1222 / 1002005 n following work to be carried : n ( a ) calibration of injector to be done 335 1021 ndd compressor engine, make kirloskar oil engine, model taf1, sl. no 20.1222 / 1002005 n following work to be carried : n ( b ) caliberation of fip & governor assembly to be carried out. 336 1021 ndd compressor engine, make kirloskar oil engine, model taf1, sl. no 20.1222 / 1002005 n following work to be carried : n ( c ) lub oil sump to be drained, cleaned & new oil to be charged in sump. 337 1021 ndd compressor engine, make kirloskar oil engine, model taf1, sl. no 20.1222 / 1002005 n following work to be carried : n ( d ) sump strainers / filter to be renewed. 338 1021 ndd compressor engine, make kirloskar oil engine, model taf1, sl. no 20.1222 / 1002005 n following work to be carried : n ( e ) fuel oil filter to be renewed. 339 1021 ndd compressor engine, make kirloskar oil engine, model taf1, sl. no 20.1222 / 1002005 n following work to be carried : n ( f ) lub oil pressure gauge to be renewed. 340 1021 ndd compressor engine, make kirloskar oil engine, model taf1, sl. no 20.1222 / 1002005 n following work to be carried : n ( g ) renewal of air inlet filter element of engine to be carried out. 341 1021 ndd compressor engine, make kirloskar oil engine, model taf1, sl. no 20.1222 / 1002005 n following work to be carried : n ( h ) engine to be painted post boxing up and proved for satisfactory perfomance. 342 nelectrical work package n2001 nall electrical power components / spares like contactors, overload relays, etc are to to be sourced from navy approved vendors. nimportant note: following points are applicable for all relevant dls and shipyards / firms to consider and quote accordingly. n ( a ) renewal of items / spares: n ( i ) renewal of items / spares wherever mentioned in the qdl to be undertaken by shipyard / firm as per the sample / drawing / details provided by ss / coa / rmt. n ( ii ) shipyard / firm should undertake the routines / overhaul of the equipment including the mandatory spares required for undertaking the same, irrespective of the spares mentioned in the mandatory spares list provided by nd ( v ) . n ( iii ) further, the cost should include the degutting of existing item, supply of new item, fitment and proving of the system post renewal. nfollowing as fitted drawings need to be prepared and handed over to ships staff n ( a ) foundations of new equipment n ( b ) electrical cabling n ( c ) all as and as including internals of control panel ( hull, engineering & electrical ) . n ( d ) aber replacement ( hull, engineering & electrical ) . 343 2001 neqpt / system:main swich board make : l&t , rating: 415v, 3ph, 50hz. n ( a ) msb to be overhauled ( includes defective swiches to be renwed, indication lamp to be renewed, perished control wiring to be renewed with crimping of proper lugs , making sleeves to be put on control wiring and loose wirng to be tied with cable ties ) 344 2001 neqpt / system:main swich board make : l&t , rating: 415v, 3ph, 50hz. n ( a ) msb to be overhauled ( includes defective swiches to be renwed, indication lamp to be renewed, perished control wiring to be renewed with crimping of proper lugs , making sleeves to be put on control wiring and loose wirng to be tied with cable ties ) n ( i ) replacement with new one of selector swiches 3 pole , 3 way, 16 a, 415v 345 2001 neqpt / system:main swich board make : l&t , rating: 415v, 3ph, 50hz. n ( a ) msb to be overhauled ( includes defective swiches to be renwed, indication lamp to be renewed, perished control wiring to be renewed with crimping of proper lugs , making sleeves to be put on control wiring and loose wirng to be tied with cable ties ) n ( ii ) replacement with new one of selector swiches 2 pole , 2 way, 16 a, 415v 346 2001 neqpt / system:main swich board make : l&t , rating: 415v, 3ph, 50hz. n ( a ) msb to be overhauled ( includes defective swiches to be renwed, indication lamp to be renewed, perished control wiring to be renewed with crimping of proper lugs , making sleeves to be put on control wiring and loose wirng to be tied with cable ties ) n ( iii ) replacement with new one of selector swiches 6 pole , 2 way, 16 a, 415v door mounting type , size 48x48 mm 347 2001 neqpt / system:main swich board make : l&t , rating: 415v, 3ph, 50hz. n ( a ) msb to be overhauled ( includes defective swiches to be renwed, indication lamp to be renewed, perished control wiring to be renewed with crimping of proper lugs , making sleeves to be put on control wiring and loose wirng to be tied with cable ties ) n ( iv ) replacement with new one of emergey push button swich, type : mushroom head push turn with 1nc contract, model:hh55c1+hc61b2 348 2001 neqpt / system:main swich board make : l&t , rating: 415v, 3ph, 50hz. n ( a ) msb to be overhauled ( includes defective swiches to be renwed, indication lamp to be renewed, perished control wiring to be renewed with crimping of proper lugs , making sleeves to be put on control wiring and loose wirng to be tied with cable ties ) n ( v ) replacement with new one of led indication lamps fittings of different colors ( red 10, yellow 05 , blue 05, green 10, white 05, amber 05 ) , make: teknic, model :p2plbrr240, input supply 240vac 50hz 349 2001 neqpt / system:main swich board make : l&t , rating: 415v, 3ph, 50hz. n ( b ) replacement with new one of following mccbs n ( firm not to quote ) 350 2001 neqpt / system:main swich board make : l&t , rating: 415v, 3ph, 50hz. n ( b ) replacement with new one of following mccbs n ( i ) make : l &t model:dn2 250 , rating 250a 3 pole, 1 aux contact, +i trip alam, shuunt release 240v ac 50hz, thermal setting 200 250 , magnetinc setting:1500 2500 351 2001 neqpt / system:main swich board make : l&t , rating: 415v, 3ph, 50hz. n ( b ) replacement with new one of following mccbs n ( ii ) make : l &t model:dn2 250 , rating 250a 3 pole, 1 aux contact, +i trip alam, with 240v ac 50hz u / v release, thermal setting 200 250 , magnetinc setting:1500 250071 352 2001 neqpt / system:main swich board make : l&t , rating: 415v, 3ph, 50hz. n ( b ) replacement with new one of following mccbs n ( iv ) auxiliary contactor , make l&t, model mw0 , coil voltage : 240v ac 50hz, with 2no+ 2nc contacts and addon: 2nc 353 2001 neqpt / system:main swich board make : l&t , rating: 415v, 3ph, 50hz. n ( c ) check &calibrate all parameters of insulation monitoring relay , make: selco , model :t3200 354 2001 neqpt / system:main swich board make : l&t , rating: 415v, 3ph, 50hz. n ( c ) operating parameter of insulating monitoring relay ( i ) voltage tolarance :+10 20% of undervoltage ( ii ) power consumption : 2va max ( iii ) frequency range :45 65 hz ( iv ) operating temperature range : 20+70 c ( v ) contact rating :ac 2a, 380v , 250va&dc110v, 2a, 150w ( vi ) dielectric :2500v, 50hz ( vii ) presetting 0 5m ohm ( viii ) accuracy signal :+ / 5% ( of preset valve ) ( ix ) instrument scale 0 5 m ohm ( x ) instrument resistance max 100 ohm 355 2001 neqpt / system:main swich board make : l&t , rating: 415v, 3ph, 50hz. n ( d ) replacement with new one of insulation monitoring relay. make: selco, model:t3200 356 2001 neqpt / system:main swich board make : l&t , rating: 415v, 3ph, 50hz. n ( e ) calibration of following meters, if found defective the same to be replaced 357 2001 neqpt / system:main swich board make : l&t , rating: 415v, 3ph, 50hz. n ( e ) calibration of following meters, if found defective the same to be replaced n ( i ) ammeter : 415v ac, input model ct operated, ct retio 250 / 1a, accuracy class 1, range 0 250a , red mark at 195a, size : 96x96mm, gasket required 358 2001 neqpt / system:main swich board make : l&t , rating: 415v, 3ph, 50hz. n ( e ) calibration of following meters, if found defective the same to be replaced n ( ii ) kw meter : input voltage 415 v ac, 50hz, accuracy class :1 , scale 90 degrees , input current 250 / 1a range 20 0 150kw ( dynemometric ) , red mark at 122 kw, size: 96x96 mm, gasket required 359 2001 neqpt / system:main swich board make : l&t , rating: 415v, 3ph, 50hz. n ( e ) calibration of following meters, if found defective the same to be replaced n ( iii ) frequency meter :reed type, input voltage 415vac 50 hz, accuracy class 1, range 45 50 55 hz size :96x96 mm , gasket required 360 2001 neqpt / system:main swich board make : l&t , rating: 415v, 3ph, 50hz. n ( e ) calibration of following meters, if found defective the same to be replaced n ( iv ) voltmeter :range 0 500v ac, red mark 415v, accuracy class 1, scale 90 degree, vt ratio : direct input size:96x96 mm, gasket required 361 2001 neqpt / system:main swich board make : l&t , rating: 415v, 3ph, 50hz. n ( f ) rubber mat : insulating rubber mat deteriorated. to be renewed with high voltage electrical rubber mat in front of msb. ( thickness 3mm ) make vardhaman model class c 362 2002 n eqpt / system: control panels: the following control panel are to be overhauled &made operational. 363 2002 n eqpt / system: control panels: the following control panel are to be overhauled &made operational. n ( a ) anchor windlass control panel ( including master controller ) 415v, 5.5 / 11 kw, 50 hz. double speed make: electronic control corporation 364 2002 n eqpt / system: control panels: the following control panel are to be overhauled &made operational. n ( b ) ventillation group starter panel, make : electronic control corporation , rating :415v, 3ph, 50hz. and 230 v, 1ph, 50hz combined 365 2002 n eqpt / system: control panels: the following control panel are to be overhauled &made operational. nb ( i ) repair / calibrate with new one of solid state over load relay. make:semens, model:3rb22 / 23 over load relays ( screw connection ) 366 2002 n eqpt / system: control panels: the following control panel are to be overhauled &made operational. n ( c ) boat davit control panel rating : 415v, 3ph, 50 hz. 7.5 hp, make : electronic control corporation 367 2003 neqpt / system: transformer 21 kva make; radiant electronic 415v, 3ph, 50hz / 230v, 3ph , 50hz 368 2003 neqpt / system: transformer 21 kva make; radiant electronic 415v, 3ph, 50hz / 230v, 3ph , 50hz n ( a ) carryout overhaul routines and proove them for satisfactory performance / made operational 369 2003 neqpt / system: transformer 21 kva make; radiant electronic 415v, 3ph, 50hz / 230v, 3ph , 50hz n ( b ) clean it internaly , dust and moisture to be removed and to be painted outside with gray color 370 2003 neqpt / system: transformer 21 kva make; radiant electronic 415v, 3ph, 50hz / 230v, 3ph , 50hz n ( c ) renew the internal wiring of transformer ( in between the connectors to fuse units ) 371 2004 neqpt / system: straight line window wiper & cvs make : rakme engineering , size: stroke 500mm , blade 600mm, motor rating: ac 230 v: 0.5 hp , 1 ph 372 2004 neqpt / system: straight line window wiper & cvs make : rakme engineering , size: stroke 500mm , blade 600mm, motor rating: ac 230 v: 0.5 hp , 1 ph n ( a ) overhaul the gear system and prove them fpr free movement / satisfactory performance 373 2004 neqpt / system: straight line window wiper & cvs make : rakme engineering , size: stroke 500mm , blade 600mm, motor rating: ac 230 v: 0.5 hp , 1 ph n ( b ) fw system line to be proved ( dia 10mm, cu ni ) 374 2004 neqpt / system: straight line window wiper & cvs make : rakme engineering , size: stroke 500mm , blade 600mm, motor rating: ac 230 v: 0.5 hp , 1 ph n ( c ) renew the blades including rubber coambing 375 2004 neqpt / system: straight line window wiper & cvs make : rakme engineering , size: stroke 500mm , blade 600mm, motor rating: ac 230 v: 0.5 hp , 1 ph n ( d ) overhaul the cvs motor and prove it operational. 376 2004 neqpt / system: straight line window wiper & cvs make : rakme engineering , size: stroke 500mm , blade 600mm, motor rating: ac 230 v: 0.5 hp , 1 ph n ( e ) machinery body to be bare metal and painted with one cote of primer and two coat of enamil paint 377 2005 neqpt / system:navigational lighting panels ( ac &dc ) make: electronic control corporation 230v ac / 24 v dc combined ( including internal parts of control panel such as fuse, led indication lamp, control pcbs , connectors etc ) 378 2005 neqpt / system:navigational lighting panels ( ac &dc ) make: electronic control corporation 230v ac / 24 v dc combined ( including internal parts of control panel such as fuse, led indication lamp, control pcbs , connectors etc ) n ( a ) carryout routines mentioned below and prove them for satisfactory performance 379 2005 neqpt / system:navigational lighting panels ( ac &dc ) make: electronic control corporation 230v ac / 24 v dc combined ( including internal parts of control panel such as fuse, led indication lamp, control pcbs , connectors etc ) na ( i ) clean &tighten the all connection with proper lugs, 380 2005 neqpt / system:navigational lighting panels ( ac &dc ) make: electronic control corporation 230v ac / 24 v dc combined ( including internal parts of control panel such as fuse, led indication lamp, control pcbs , connectors etc ) na ( ii ) check the functions of all fuse units, control cards, indication lamp &horn. 381 2005 neqpt / system:navigational lighting panels ( ac &dc ) make: electronic control corporation 230v ac / 24 v dc combined ( including internal parts of control panel such as fuse, led indication lamp, control pcbs , connectors etc ) na ( iii ) if deffective repair them 382 2005 neqpt / system:navigational lighting panels ( ac &dc ) make: electronic control corporation 230v ac / 24 v dc combined ( including internal parts of control panel such as fuse, led indication lamp, control pcbs , connectors etc ) na ( iv ) if un repairable than renew them. 383 2005 neqpt / system:navigational lighting panels ( ac &dc ) make: electronic control corporation 230v ac / 24 v dc combined ( including internal parts of control panel such as fuse, led indication lamp, control pcbs , connectors etc ) n ( b ) if control card found defective repair them 384 2005 neqpt / system:navigational lighting panels ( ac &dc ) make: electronic control corporation 230v ac / 24 v dc combined ( including internal parts of control panel such as fuse, led indication lamp, control pcbs , connectors etc ) n ( c ) renew theled indication lamps with holders 385 2005 neqpt / system:navigational lighting panels ( ac &dc ) make: electronic control corporation 230v ac / 24 v dc combined ( including internal parts of control panel such as fuse, led indication lamp, control pcbs , connectors etc ) n ( e ) renw the fuse units screw type connectors 386 2005 neqpt / system:navigational lighting panels ( ac &dc ) make: electronic control corporation 230v ac / 24 v dc combined ( including internal parts of control panel such as fuse, led indication lamp, control pcbs , connectors etc ) n ( f ) check the circuits ( cables ) in between the control panel & navigational light fitting if there is any fault rectify them 387 2005 neqpt / system:navigational lighting panels ( ac &dc ) make: electronic control corporation 230v ac / 24 v dc combined ( including internal parts of control panel such as fuse, led indication lamp, control pcbs , connectors etc ) n ( g ) renew the cables ( single core cable , 2mm sq ) ( incomming &outgoing ) if they are pershed. 388 2006 neqpt / system: light fittings. n ( a ) renew following light fittings 389 2006 neqpt / system: light fittings. n ( a ) renew following light fittings n a ( i ) navigational light fittings ( ac &dc ) make :m / s arvin industries 230 v for ac, 24v fot dc ( two ties set ) red 03, green 01, white 04 390 2006 neqpt / system: light fittings. n ( a ) renew following light fittings na ( ii ) renew the ac navigational bulbs 230v, 60w 391 2006 neqpt / system: light fittings. n ( a ) renew following light fittings na ( iii ) renew the dc navigational bulbs 24v, 60w 392 2006 neqpt / system: light fittings. n ( a ) renew following light fittings n a ( iv ) renew weather deck light fittings 230v, 60w 393 2006 neqpt / system: light fittings. n ( a ) renew following light fittings na ( v ) renew watertight u glass light fitting incandeescent lamp fittings. 230v, 60w 394 2006 neqpt / system: light fittings. n ( a ) renew following light fittings na ( vi ) replace 230v, 60w lamo with 230v 11 w led lamp, make: syska 395 2006 neqpt / system: light fittings. n ( a ) renew following light fittings n a ( vii ) replace the 230v 200w reflector light fitting with 230v 100 w led light fitting 396 2006 neqpt / system: light fittings. n ( b ) repair and overhaul following light fittings 397 2006 neqpt / system: light fittings. n ( b ) repair and overhaul following light fittings n b ( i ) search light fitting 230v, 1000w 398 2006 neqpt / system: light fittings. n ( b ) repair and overhaul following light fittings nb ( ii ) renew twin tube cfl lamp 230v, 11w 399 2006 neqpt / system: light fittings. n ( b ) repair and overhaul following light fittings n b ( iii ) renew emenrgency light led lamp ( operating range of voltage 13v 24v ) dc , 6w 400 2006 neqpt / system: light fittings. n ( c ) convert all 230v, 2x20w tubelight fitting with 230v, 2x20w led tubelight fitting 401 2006 neqpt / system: light fittings. n ( d ) provide the 20w 230v led tubelights, make:philips / siska 402 2007 n eqpt / system: d / g ( port &stbd ) alarm panel system make : kirloskar and crompton, type :176 bhp ( oem to be in volved ) 403 2007 n eqpt / system: d / g ( port &stbd ) alarm panel system make : kirloskar and crompton, type :176 bhp ( oem to be in volved ) n ( a ) d / g ( port &stbd ) av alaram panel system including control wiring to be completely over hauled, calibrated and proved for satifactory opration. 404 2007 n eqpt / system: d / g ( port &stbd ) alarm panel system make : kirloskar and crompton, type :176 bhp ( oem to be in volved ) n ( b ) repair of dynamo to be carried out 24v dc make :iucas tvs 405 2007 n eqpt / system: d / g ( port &stbd ) alarm panel system make : kirloskar and crompton, type :176 bhp ( oem to be in volved ) n ( c ) overhauling of self starter motor 24v dc, make : iucas tvs 406 2007 n eqpt / system: d / g ( port &stbd ) alarm panel system make : kirloskar and crompton, type :176 bhp ( oem to be in volved ) n ( d ) repair of ievr units, 407 2007 n eqpt / system: d / g ( port &stbd ) alarm panel system make : kirloskar and crompton, type :176 bhp ( oem to be in volved ) n ( e ) calibration of following cutouts of da 408 2007 n eqpt / system: d / g ( port &stbd ) alarm panel system make : kirloskar and crompton, type :176 bhp ( oem to be in volved ) ne ( i ) fresh water temperature cut outs for alarm set point 92 degree c and tripping at set point 97 degrees c 409 2007 n eqpt / system: d / g ( port &stbd ) alarm panel system make : kirloskar and crompton, type :176 bhp ( oem to be in volved ) ne ( ii ) lub oil temp cutout for alarm set point 97 degrees c and trip at 105 degree c 410 2007 n eqpt / system: d / g ( port &stbd ) alarm panel system make : kirloskar and crompton, type :176 bhp ( oem to be in volved ) ne ( iii ) lub oil pressure cut out for alarm set point 1.5 kg / sq cm and tripping set point 0.5 kg / sq cm 411 2007 n eqpt / system: d / g ( port &stbd ) alarm panel system make : kirloskar and crompton, type :176 bhp ( oem to be in volved ) ne ( iv ) over speed cut out for tripping set point 1650 rpm 412 2007 n eqpt / system: d / g ( port &stbd ) alarm panel system make : kirloskar and crompton, type :176 bhp ( oem to be in volved ) ne ( v ) over temperature of alternator for tripping set point 70 degreec 413 2007 n eqpt / system: d / g ( port &stbd ) alarm panel system make : kirloskar and crompton, type :176 bhp ( oem to be in volved ) n ( f ) renew the following sensors / relays if found defective 414 2007 n eqpt / system: d / g ( port &stbd ) alarm panel system make : kirloskar and crompton, type :176 bhp ( oem to be in volved ) nf ( i ) temperature sensors ( 0 to 200 ) danfoss temperature sensor 415 2007 n eqpt / system: d / g ( port &stbd ) alarm panel system make : kirloskar and crompton, type :176 bhp ( oem to be in volved ) nf ( ii ) pressure sensors ( 0 to 10 ) danfoss pressure transmitter 416 2007 n eqpt / system: d / g ( port &stbd ) alarm panel system make : kirloskar and crompton, type :176 bhp ( oem to be in volved ) nf ( iii ) magnetic switch contactors relays 24v dc, make: cummins / kirloskar n 417 2007 n eqpt / system: d / g ( port &stbd ) alarm panel system make : kirloskar and crompton, type :176 bhp ( oem to be in volved ) nf ( iv ) digital rpm meter operating voltage 24v dc 418 2008 neqpt / system: co2 existinguishing system control panel. make :shm shipcare, kolkata 419 2008 neqpt / system: co2 existinguishing system control panel. make :shm shipcare, kolkata n ( a ) carryout complete overhaul of the co2 control panel including renewal of defective parts / componenets ( such as indication led, alarm hooter, control pcbs fuse holders, fuses, connection terminals, perished wiring etc ) and prove it for satisfactory performance. 420 2008 neqpt / system: co2 existinguishing system control panel. make :shm shipcare, kolkata n ( b ) overhaul the motorised siren & flasher make: kheraj type horozontal single mounting 24v, dc, 75w, 6000rpm, range 800 mtrs 421 2008 neqpt / system: co2 existinguishing system control panel. make :shm shipcare, kolkata n ( c ) limit switches ( 05 ) and solenoid valves relays ( 05 ) to be checked, calibrated to be proved for satisfactory operation 422 2008 neqpt / system: co2 existinguishing system control panel. make :shm shipcare, kolkata n ( d ) check, calibrate & set to their set point of heat detectors and smoke detectors, type: nittan uk ns dhg1 set point. 423 2008 neqpt / system: co2 existinguishing system control panel. make :shm shipcare, kolkata n ( e ) check, calibrate & set to their set point of pressure operated switch 1no make: ginger kerr working pressure 3 150bar 424 2008 neqpt / system: co2 existinguishing system control panel. make :shm shipcare, kolkata n ( f ) repair heat detectors and smoke detectors, type:nittan uk ns dhg1 set point 58°c 425 2009 neqpt / system: shore supply box: make : electronic control corporation rating:100 amps, 415v, 3ph, 50hz. 426 2009 neqpt / system: shore supply box: make : electronic control corporation rating:100 amps, 415v, 3ph, 50hz. n ( a ) carryout complete overhaul of the shore supply control panel prove it for satisfactory performance 427 2009 neqpt / system: shore supply box: make : electronic control corporation rating:100 amps, 415v, 3ph, 50hz. n ( b ) renew the indication lamps with holders ( red, yellow, blue ) 428 2009 neqpt / system: shore supply box: make : electronic control corporation rating:100 amps, 415v, 3ph, 50hz. n ( c ) renewal of shore supply panel plastic glass size 24x12 429 2009 neqpt / system: shore supply box: make : electronic control corporation rating:100 amps, 415v, 3ph, 50hz. n ( d ) mechanical cleaning of supply panel board & painted with one cote of primer and two coat of powder coating ( original colour ) from inside any gray color from outside 430 2010 neqpt / system: smf lead acid batteries. make: exide, 200ah, 12v 431 2010 neqpt / system: smf lead acid batteries. make: exide, 200ah, 12v n ( a ) renew the maintainence free battery 432 2010 neqpt / system: smf lead acid batteries. make: exide, 200ah, 12v n ( b ) clean & tighten the all connections with proper lugs, ferrules & connectors 433 2010 neqpt / system: smf lead acid batteries. make: exide, 200ah, 12v n ( c ) renew the battery connectors ( 12+ive and 12 ve ) 434 2010 neqpt / system: smf lead acid batteries. make: exide, 200ah, 12v n ( d ) renew the short link cable ( 50sq.mm multi stand copper cables, length 0.5 mtr ) conncetors 435 2010 neqpt / system: smf lead acid batteries. make: exide, 200ah, 12v n ( e ) renew the parallel link cable ( 50sq.mm multi stand copper cables length 0.5mtr ) with connectors in emergency batteries bank 436 2011 neqpt / system: submersible pump& lts starter, make: mody, capacity 20 tph below mentioned routine to be carried out ( firm not to quote ) 437 2011 neqpt / system: submersible pump& lts starter, make: mody, capacity 20 tph below mentioned routine to be carried out n ( a ) carryout complete overhaul routines and prove them for satisfactory performance / made operational 438 2011 neqpt / system: submersible pump& lts starter, make: mody, capacity 20 tph below mentioned routine to be carried out n ( b ) check & calibrate the olrs / spps / timers / mcbs as per their ratings if defective replace them 439 2011 neqpt / system: submersible pump& lts starter, make: mody, capacity 20 tph below mentioned routine to be carried out n ( c ) check all the fuse units if defective replace them 440 2011 neqpt / system: submersible pump& lts starter, make: mody, capacity 20 tph below mentioned routine to be carried out n ( d ) renew the neoprene rubber gasket for water tight purpose for door 441 2012 neqpt / system: transrectifier cum battery chargering units make: radient electronics ninput: 415v, 3ph, 50hz. output 22v to 29v dc, 63a 442 2012 neqpt / system: transrectifier cum battery chargering units make: radient electronics ninput: 415v, 3ph, 50hz. output 22v to 29v dc, 63a ncarryout complete overhaul routines and proove them for satisfactory performance / made operational. defective componenets tp be replaced with new one ( indication lamp, fuse carrier, fuses, connector terminals, lugs, perished control wring ) 443 2013 neqpt / system: sewage treatment plant; nmake / model : exceltec omnipure 7 me, capacity : 1200 gallon / day. 444 2013 neqpt / system: sewage treatment plant; nmake / model : exceltec omnipure 7 me, capacity : 1200 gallon / day. n ( a ) overhaul control panel fitted onboard and prove it for satisfactory performance. all contactor, timer, overload relay, pcb is to be overhauled and proved for satisfactory performance. 445 2013 neqpt / system: sewage treatment plant; nmake / model : exceltec omnipure 7 me, capacity : 1200 gallon / day. n ( b ) overhaul motor and prove it for satisfactory performance. 446 2013 neqpt / system: sewage treatment plant; nmake / model : exceltec omnipure 7 me, capacity : 1200 gallon / day. n ( c ) perished wiring of control panel is to be changed. ( single core, 1sqmm ) 447 2013 neqpt / system: sewage treatment plant; make / model : exceltec omnipure 7 me, capacity : 1200 gallon / day. n ( d ) all indication lamp is to be renewed. 448 2014 neqpt / system: motors over hauling: carry out complete over hauling of the following motors and prove for satisfactory operation. only zz standard bearing ( skf / fag ) is to be used. 449 2014 neqpt / system: motors over hauling: carry out complete over hauling of the following motors and prove for satisfactory operation. only zz standard bearing ( skf / fag ) is to be used. n ( a ) anchor windlass motor double speed motor415v 3ph, 50hz, 5.5 / 11 kw 450 2014 neqpt / system: motors over hauling: carry out complete over hauling of the following motors and prove for satisfactory operation. only zz standard bearing ( skf / fag ) is to be used. n ( b ) boat dvit hoist / lowering motor, 415v, 3ph, 50 hz, 7.5 hp 451 2014 neqpt / system: motors over hauling: carry out complete over hauling of the following motors and prove for satisfactory operation. only zz standard bearing ( skf / fag ) is to be used. n ( c ) dirty oil pump motor, 415 v, 3 ph, 50 hz, 1.5 hp 452 2014 neqpt / system: motors over hauling: carry out complete over hauling of the following motors and prove for satisfactory operation. only zz standard bearing ( skf / fag ) is to be used. n ( d ) fuel oil transfer pump motor 415 v, 3 ph, 50 hz, 1.1 kw 453 2014 neqpt / system: motors over hauling: carry out complete over hauling of the following motors and prove for satisfactory operation. only zz standard bearing ( skf / fag ) is to be used. n ( e ) air compressor motor 415 v, 3 ph, 50 hz, 3.7 kw 454 2014 neqpt / system: motors over hauling: carry out complete over hauling of the following motors and prove for satisfactory operation. only zz standard bearing ( skf / fag ) is to be used. n ( f ) fuel ( hsd ) cargo pump motor 415 v, 3 ph, 50 hz, 15 hp 455 2014 neqpt / system: motors over hauling: carry out complete over hauling of the following motors and prove for satisfactory operation. only zz standard bearing ( skf / fag ) is to be used. n ( g ) fresh water cargo pump 415 v, 3 ph, 50 hz, 12.5 hp 456 2014 neqpt / system: motors over hauling: carry out complete over hauling of the following motors and prove for satisfactory operation. only zz standard bearing ( skf / fag ) is to be used. n ( h ) fresh water pump motor 415 v, 3 ph, 50 hz, 1.5 hp 457 2014 neqpt / system: motors over hauling: carry out complete over hauling of the following motors and prove for satisfactory operation. only zz standard bearing ( skf / fag ) is to be used. n ( j ) main engine primming pump motor 415 v, 3 ph, 50 hz, 1 hp 458 2014 neqpt / system: motors over hauling: carry out complete over hauling of the following motors and prove for satisfactory operation. only zz standard bearing ( skf / fag ) is to be used. n ( k ) steering gear compartment supply fan motor 415 v, 3 ph, 50 hz, 0.37 w 459 2014 neqpt / system: motors over hauling: carry out complete over hauling of the following motors and prove for satisfactory operation. only zz standard bearing ( skf / fag ) is to be used. n ( l ) pump room supply / exhaust fan motor 415 v, 3 ph, 50 hz, 0.37 w 460 2014 neqpt / system: motors over hauling: carry out complete over hauling of the following motors and prove for satisfactory operation. only zz standard bearing ( skf / fag ) is to be used. n ( m ) engine room supply fan motor 415 v, 3 ph, 50 hz, 5.5 kw 461 2014 neqpt / system: motors over hauling: carry out complete over hauling of the following motors and prove for satisfactory operation. only zz standard bearing ( skf / fag ) is to be used. n ( n ) engine room exhaust fan motor 415 v, 3 ph, 50 hz, 5.5kw 462 2014 neqpt / system: motors over hauling: carry out complete over hauling of the following motors and prove for satisfactory operation. only zz standard bearing ( skf / fag ) is to be used. n ( p ) galley exhaust fan motor 230 v, 1 ph, 50hz, 157w 463 2014 neqpt / system: motors over hauling: carry out complete over hauling of the following motors and prove for satisfactory operation. only zz standard bearing ( skf / fag ) is to be used. n ( q ) co2 room exhaust fan motor 230 v, 1 ph, 50 hz, 157 w 464 2015 neqpt / system:motor starter, n ( dol / start delta ) to be overhauled completely and prove them for satisfactory performance. overhauling includes renewal of indication lamp, conector terminals, lugs, perished internal wiring there ever as required. 465 2015 neqpt / system:motor starter, n ( a ) group starter control panel for ventilation rating: 415v, 3 ph, 50hz, and 230 v, 1 ph, 50 hz, combined make: electronic control corperation 466 2015 neqpt / system:motor starter, n ( a ) starter for dirty oil pump motor, 415 v, 3 ph, 50 hz, 1.1 kw 467 2015 neqpt / system:motor starter, n ( b ) starter for air compressor motor, 415 v, 3 ph, 50 hz, 3.7 kw 468 2015 neqpt / system:motor starter, n ( c ) starter for bilges / gs pump motor, 415 v, 3 ph, 50 hz, 7.5 kw 469 2015 neqpt / system:motor starter, n ( d ) starter for fuel cargo pump motor, 415 v, 3 ph, 50 hz, 15 hp 470 2015 neqpt / system:motor starter, n ( e ) starter for steering gear motor, 415 v, 3 ph, 50 hz, 15 hp 471 2015 neqpt / system:motor starter, n ( f ) starter for fresh water cargo pump 415 v, 3 ph, 50 hz, 12.5 hp 472 2015 neqpt / system:motor starter, n ( g ) starter for avcat transfer pump motor, 415 v, 3 ph, 50 hz, 10 hp 473 2015 neqpt / system:motor starter, n ( h ) starter for fresh water cargo pump 415 v, 3 ph, 50 hz, 1.5 hp 474 2015 neqpt / system:motor starter, n ( j ) starter for main engine primming pump motor, 415 v, 3 ph, 50 hz, 1 hp 475 2015 neqpt / system:motor starter, n ( k ) starter for fuel oil seperator motor, 415 v, 3 ph, 50 hz, 5 hp 476 2016 nequipment : sound power telephone system ( firm not to quote ) 477 2016 nequipment : sound power telephone system n ( a ) carryout complete overhauling of sound power telephone system. including repair of telephone handset mic and speaker. prove the system for satisfectory performance ( total spt position 10 ) 478 2017 nair compressor control panel ( firm not to quote ) 479 2017 nair compressor control panel n ( a ) air compressor control panel change over switch & other panels bodies perished, to be renwed / manufactured as per dianentions ( 12 x 12 x 12 ) 480 2017 nair compressor control panel n ( b ) magnetic starter to check for proper operation, repair / renew defective items. 481 2017 nair compressor control panel n ( c ) pressure switch to calibrated 482 2017 nair compressor control panel n ( d ) starter coil to repaired 483 2018 neqpt / system:refrigerator ( d.door ) . nrepair the refrigerators of double door 350ltrs, 5star lg invertor model 484 2019 n eqpt / system:deep freezer nrepair / overhauling of deep freezers 200ltrs ( presently working ) 485 2020 neqpt / system:hot water boiler nmake:spherehot ( brand name ) manufactured by kantilal chinilal & sons applaince pvt ltd., surat, india noverhauling of hot water boiler along with control panel 20ltrs 230v 486 2021 neqpt / system: cooking range with 2 hot plates with oven;430v 3ph 5kw. nmake:spherehot ( brand name ) manufactured by kantilal chinilal & sons applaince pvt ltd., surat, india n ( firm not to quote ) 487 2021 neqpt / system: cooking range with 2 hot plates with oven;430v 3ph 5kw. nmake:spherehot ( brand name ) manufactured by kantilal chinilal & sons applaince pvt ltd., surat, india n ( a ) carryout complete overhaul routines and proove them for satisfactory performance / made operational 488 2021 neqpt / system: cooking range with 2 hot plates with oven;430v 3ph 5kw. nmake:spherehot ( brand name ) manufactured by kantilal chinilal & sons applaince pvt ltd., surat, india n ( b ) heating elements found defective. renew the heating elements ( w type ) 430v, 1500w 489 2022 neqpt / system:split a / cs ncarryout overhauling the 7 in nos spilt a / cs at various locations, 1.5 ton, make:carrier 490 2022 neqpt / system:split a / cs n ( a ) carry out servicing and gas charging of splict ac fitted.renew if found ber . ( a / c capacity 1.5 t ) 491 mandatory spares of poshak cummins main engine ngasket l.o. cooler n121779 492 gasket oil cooler connect n68210 493 element fuel filter n3166555 494 element super lo bypass filter n3873576 n 495 ninjector nar 3239804 496 valve solenoid nar 3240573 497 element l.o. filter n3166554 498 element air filter 499 o ring n212161 500 mandatory spares of poshak kirloskar dg nelement fuel filter n4h.333.03.0.00 501 benzo bolt m 14x15 n50.504.04.000 502 heat exchanger n4h.465.16.0.pr 503 raw water pump n4h.465.19.0.pr 504 water pump sub assembly n4h.052.40.0.00 505 speed control unit esd 5221 nf6.614.02.0.00 506 fuel leak off assembly n6h.1124.30.0.00 507 lub oil cooler assembly n6h.113.60.0.00 508 element l.o. filter n03.040.19.0.00 509 expansion tank n6h.466.28.0.00 510 fuel pipe n6h.081.02.0.00 511 fuel pipe n6h.081.03.0.00 512 element air filter n03.061.40.0.00 513 magnetic pick up n46.179.05.0.00 514 starter ( sm130pe ) nf6.028.01.0.00 515 fuel filter n48.117.10.0.00 516 primary filter element nf6.504.34.0.00 517 electronic governor aseembly nf6.886.10.0.00 518 link for adc c225 gs nf6.741.02.0.00 519 mandatary spares of ingersoll rand air compressor ( model 251 ) npriority valve n70241336 520 filter inlet complete n94495256 521 element filter n70234737 522 valve safety n70239801 523 piston air n30292429 524 set ring n32194276 525 gasket flange n30294227 526 set ring n37138229 527 piston air n30215412 n 528 dry dock and allied services work package n ( a ) docking and undocking charges ( both versions ) nfirm not to quote. docking and undocking will be done by navy in navy permises i.e nd ( v ) / slipway. 529 ( b ) dock blocks preparation & laying out as per docking plan nfirm not to quote. job will be done by navy 530 dock hire charges for an estimated duration of 60 days as per ocr nfirm not to quote. dry dock facility will provided by navy in navy permises i.e nd ( v ) / slipway. 531 wet basin / alongside hire charges for the remaining duration ( i.e. total refit duration of – 60 days docking period ) nfirm not to quote. dry dock facility will will provided by navy in navy permises 532 provision of sufficient lighting for duty staff nfirm to quote. 533 quote for maintenance of two in no. fire lines for the refit duration . nfirm to quote. 534 provision of two transports ( cars ) for entire refit duration ( one for refit co ordinating staff and one for nd ( v ) monitoring team ) for 12 hrs or 100km / day whichever is less n nfirm to quote. 535 provision of stationory / office items for nd ( v ) / refit monitoring team for entire refit duration period. cater budget of rs 2000 / per month. requirement will be intimated rmt / ndv on as requirement basis. payment at actuals. n nnote: firms to quote. 536 mail man services ( 02 nos ) for entire refit duration ( one for user department and one for planning / co ordinating department ) to be provided for 10 hrs per day nfirm to quote. 537 qc inspection for the entire scope of work by third party irs / lrs / abs / qc / tpi for the refit duration as per the qis. nfirm not to quote. services will be provided by nd ( v ) / qc...
Due Date : April 01, 2021
