Municipalities - Andhra Pradesh

40895779 providing exterior emulsion paint to divider from south bye pass fly over bridge to addanki bus stand along kurnool road in ongole municipal corporation...

Department Of Atomic Energy - Andhra Pradesh

40330807 bids are invited for construction of bhabha community hall at rk palle 1 earth work in excavation by mechanical means hydraulic excavator manual means over areas exceeding 30 cm in depth 1 point 5 m in width as well as 10 sqm on plan including getting out and disposal of excavated earth lead up to 50 m and lift up to 1point 5 m as directed by engineer in charge in all kinds of soil 2 filling available excavated earth excluding rock in trenche plinth sides of foundations etc in layers not exceeding 20cm in depth consolidating each deposited layer by ramming and watering lead up to 50 m and lift up to 1 point5 m as per specifications and drawings 3 providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering at all leads and lift but including curing etc as per directions of engineer in charge 1 ratio3 ratio6 1 cement 3 coarse sand 6 graded stone aggregate 20 mm nominal size 4 providing and laying in position specified grade of reinforced cement concrete excluding the cost of centering shuttering finishing and reinforcement at all leads and lift including curing etc complete as per directions of engineer in charge1 ratio1 point 5ratio 3 1 cement 1point5 coarse sand 3 graded stone aggregate 20 mm and down nominal size 5 centering and shuttering including strutting propping etc. and removal of form as per directions of engineer in charge at all leads and lift in foundationsfootings bases of columns etc 6 centering and shuttering including strutting propping etc and removal of form as per directions of engineer in charge at all leads and lift in superstructure columns lintels beams plinth beams roofs etc 7 steel reinforcement for rcc work including straightening cutting bending placing in position and binding all complete at all leads and lift thermo mechanically treated bars of grade fe 500d or more 8 brick work with common fly ash bricks of class of approved quality designation 7point5 in at all levels and lift as per directions of engineer in charge as per specifications and drawings complete cement mortar 1ratio 6 1 cement 6 coarse sand 9 providing and fixing isi marked flush door shutters conforming to is 2202 part i non decorative type core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters including a coat of approved primer complete 35 mm thick including isi marked stainless steel butt hinges with necessary screws as per directions of engineer in charge 10 providing and fixing isi marked oxidised ms sliding door bolts with nuts and screws etc complete 300x16 mm 11 providing and fixing isi marked oxidised ms tower bolt black finish barrel type with necessary screws etc complete 250x10 mm 12 providing and fixing isi marked oxidised ms tower bolt black finish barrel type with necessary screws etc complete 150x10 mm 13 providing and fixing bright finished brass hanging type floor door stopper with necessary screws etc complete 14 fixing standard steel glazed doors, windows and ventilators in walls, including fixing of float glass panes with glazing clips and special metal sash putty of approved make or metal beading with screws and fixing glass panes with silicon gel glass panes shall be paid separately fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of cc 1ratio3ratio6 1 cement 3 coarse sand 6 graded stone aggregate 20 mm nominal size 15 structural steel work riveted bolted or welded in built up sections like hand rails grills etc including cutting hoisting fixing in position and applying a priming coat of approved steel primer all complete 16 neat cement punning 17 painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade in two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture as per directions of engineer in charge as per drawings and specificaions at all leads and lifts complete 18 providing and fixing on wall face un plasticised rigid pvc swr pipes conforming to is 13592 type a including jointing with seal ring conforming to is 5382 leaving 10 mm gap for thermal expansion single socketed pipes at all leads and lifts etc complete 110 mm diameter 19 half brick masonry with non modular fly ash bricks of class designation10 conforming to is 12894 at all leads and lifts in cement mortar 1 ratio 4 1 cement 4 coarse sand and providing wire netting at every third layer of brick work as per specifications and drawings 20 15 mm cement plaster with mix 1ratio 6 1 cement 6 fine sand at all heights and lead as per directions of engineer in charge 21 6mm cement plaster of mix 1ratio3 1 cement 3 fine sand 22 extra for providing and mixing water proofing material in cement per bag of plaster work in proportion recommended by the manufacturers 23 wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade in two or more coats with over a coat of approved primer including cost of all materials labour tools and tackles etc complete as per specifications and directions of engineer in charge finishing walls with 100percentage premium acrylic emulsion paint having voc less than 50 gm per litre and uv resistance as per is 15489 2004 24 required shade company depot tinted with silicon additive new work two or more coats applied 1point43 litre per10 sqm over and including priming coat of exterior primer applied 0 point90 litre per10 sqm 25 providing and fixing white vitreous china pedestal type water closet european type wc pan with seat and lid 10 litre low level white pvc flushing cistern including flush pipe with manually controlled device handle lever conforming to is 7231 with all fittings and fixtures complete including cutting and making good the walls and floors wherever required wc pan with isi marked at all leads and lift 26 providing and fixing wash basin with ci brackets 15 mm cp brass pillar taps 32 mm cp brass waste of standard pattern including painting of fittings and brackets cutting and making good the walls wherever require white vitreous china wash basin size 630x450 mm with 15 mm cp brass pillar taps of approved brand as per instructions 27 providing and fixing 600x450 mm beveled edge mirror of superior glass of approved quality complete with 6 mm thick ac sheetfixed to wooden cleats with cp brass screws and washers complete 28 providing and fixing gi pipes complete with gi fittings and clamps ic cutting and making good the walls etc with required excavation and back filling as required complete including as per directions of eic 15 mm dia nominal bore 29 providing and fixing gi pipes complete with gi fittings and clamps ic cutting and making good the walls etc with required excavation and back filling as required complete including as per directions of eic 20 mm dia nominal bore 30 providing and fixing gi pipes complete with gi fittings and clamps ic cutting and making good the walls etc with required excavation and back filling as required complete including as per directions of eic 25 mm dia nominal bore 31 providing and fixing gi pipes complete with gi fittings and clamps ic cutting and making good the walls etc with required excavation and back filling as required complete including as per directions of eic 32 mm dia nominal bore 32 providing and fixing gi pipes complete with gi fittings and clamps ic cutting and making good the walls etc with required excavation and back filling as required complete including as per directions of eic 40 mm dia nominal bore 33 providing and fixing gi pipes complete with gi fittings and clamps ic cutting and making good the walls etc with required excavation and back filling as required complete including as per directions of eic50 mm dia nominal bore 34 providing and fixing ball valve brass of approved quality high or low pressure with plastic floats complete as per directions of eic15 mm nominal bore 35 providing and fixing un plasticized pvc connection pipe with brass unions of approved quality and manufacture 15 mm nominal bore 45 cm length 36 providing and placing on terrace polyethylene water storage tank of approved brand is 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet outlet and overflow pipes with all fittings and connections required at site 37 providing and fixing cp brass bib cock of approved quality conforming to is 8931 15 mm nominal bore 38 providing and fixing cp brass stop cock concealed of standard design and of approved make conforming to is 8931 15 mm nominal bore 39 constructing brick masonry manhole in cement mortar 1ratio4 1 cement 4 coarse sand with rcc top slab with 1ratio1point5ratio3 mix 1 cement 1point5 coarse sand zone iii 3 graded stone aggregate 20 mm nominal size foundation concrete 1ratio 3 ratio6 mix 1 cement 3 coarse sand 6 graded stone aggregate 20 mm nominal size inside plastering 12 mm thick with cement mortar 1ratio3 1 cement 3 coarse sand finished with floating coat of neat cement and making channels in cement concrete 1 ratio 2 ratio4 1 cement 2 coarse sand 4 graded stone aggregate 20 mm nominal size finished with a floating coat of neat cement complete as per standard design inside size 90x80 cm and 45 cm deep including ci cover with frame light duty 455x610 mm internal dimensions total weight of cover and frame to be not less than 38 kg weight of cover 23 kg and weight of frame 15 kg with common burnt clay fps non modular bricks of class designation 7point5 each 40 making soak pit 2point 5m diameter 3point0 meter deep with 45 x 45 cm dry brick honey comb shaft with bricks and sw drain pipe 100mm diameter 1point 8m long complete as per standard design with common burnt clay fps non modular bricks of class designation 7point 5 41 providing and fixing water closet squatting pan indian type wc pan with 100 mm sand cast iron p or s trap 10 litre low level white pvc flushing cistern including flush pipe with manually controlled device handle lever conforming to is 7231 with all fittings and fixtures complete including cutting and making good the walls and floors wherever required with white vitreous china orissa pattern wc pan of size580x440 mm with integral type foot rests including cost of all materials, labour tools and tackles etc complete as per specifications and directions of engineer in charge 42 providing and laying ceramic glazed floor tiles of size 300x300 mm thickness to be specified by the manufacturer of 1st quality conforming to is 15622 of approved make in all colours shades except white ivory grey fume red brown, laid on 20 mm thick bed of cement mortar1 ratio 4 1 cement 4 coarse sand jointing with grey cement slurry 3point3kg per sqm including pointing the joints with white cement and matching pigments etc complete 43 random rubble masonry with hard stone in foundation and plinth including leveling up with cement concrete 1ratio 6ratio12 1 cement 6 coarse sand 12graded stone aggregate 20 mm nominal size up to plinth level with cement mortar 1ratio6 1 cement 6 coarse sand including cost of all materials tools and tackles and labour etc complete as per directions of engineer in charge 44 making plinth protection 50mm thick of cement concrete 1 ratio 3 ratio6 1 cement 3 coarse sand zone iii 6 graded stone aggregate 20 mm nominal size over 75mm thick bed of dry brick ballast 40 mm nominal size well rammed and consolidated and grouted with fine sand including necessary excavation leveling and dressing and finishing the top smooth 45 providing, laying and jointing glazed stoneware pipes of 150mm dia pipe of class sp1with stiff mixture of cement mortar in the proportion of 1ratio1 1 cement 1 fine sand including testing of joints etc complete as per directions of engineer in charge 46 providing and laying cement concrete 1ratio5 ratio10 1 cement 5 coarse sand 10 graded stone aggregate 40 mm nominal size allround sw pipes including bed concrete as per standard design with 150 mm diameter sw pipe complete as per directions of engineer in charge 47 providing and fixing inposition collapsible steel shutters with vertical channels 20x10x2 mm and braced with flat iron diagonals 20x5 mm size with top and bottom rail of t iron 40x40x6 mm with 40mm dia steel pulley complete with bolts nuts locking arrangement stoppers handles including applying a priming coat of approved steel primer 48 providing and fixing aluminium work for doors windows ventilators and partitions with extruded built up standard tubular sections appropriate z sections and other sections of approved make conforming to is 733 and is 1285 fixing with dash fasteners of required dia and size including necessary filling up the gaps at junctions ie at top bottom and sides with required epdm rubber neoprene gasket etc aluminium sections shall be smooth rust free straight, mitred and jointed mechanically wherever required including cleat angle aluminium snap beading for glazing paneling cp brass stainless steel screws all complete as per architectural drawings and the directions of engineer in charge glazing paneling and dash fasteners to be paid for separately anodised aluminium anodised transparent or dyed to requied shade according to is 1868 minimum anodic coating of grade ac 15 49 for shutters of doors windows and ventilators including providing and fixing hinges pivots and making provision for fixing of fittings wherever required including the cost of epdm rubber neoprene gasket required fittings shall be paid for separately 50 providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to is 12823 grade l type ll in panelling fixed in aluminum doors windows shutters and partition frames with cp brass stainless steel screws etc complete as per architectural drawings and directions of engineer in charge pre laminated particle board with decorative lamination on both sides 51 providing and fixing glazing in aluminium door window ventilator shutters and partitions etc with epdm rubber neoprene gasket etc complete as per the architectural drawings and the directions of engineer in charge cost of aluminium snap beading shall be paid in basic item with float glass panes of 5 mm thickness weight not less than 12point50 kg per sqm 52 providing and fixing glazing in aluminium door, window ventilator shutters and partitions etc with epdm rubber neoprene gasket etc complete as per the architectural drawings and the directions of engineer in charge cost of aluminium snap beading shall be paid in basic itemwith float glass panes of 4point 0 mm thickness weight not less than 10 kg per sqm 53 grading roof for water proofing treatment with cement concrete 1 ratio 2 ratio 4 1 cement 2 coarse sand 4 graded stone aggregate 20mm nominal size 54 providing and fixing brass 100mm mortise latch an dlock with 6 levers without pair of handles best make of approved quality for aluminium doors including necessary cutting and making good etc complete 55 providing and fixing aluminium handles isi marked anodised anodic coating not less than grade ac 10 as per is 1868 transparent or dyed to required colour or shade with necessary screws etc complete 56 providing and fixing is 12817 marked stainless steel butt hinges with stainless steel screws etc complete 125x64x1 point 90 mm 57 providing and fixing aluminium sliding door bolts isi marked anodised anodic coating not less than grade ac 10 as per is 1868 transparent or dyed to required colour or shade with nuts and screws etc complete of size 300x16 mm 58 providing and fixing bright finished brass casement window fasteners or peg stays to windows ventilators with necessary welding and machine screws etc complete weight not less than 0 point 33 kg each of 300mm long 59 providing and injecting chemical emulsion for pre constructional ant termite treatment and creating chemical barrier under and around the column pits wall trenches basement excavation top surface if plinth filling junction of wall and floor along the external primer of binding expansion joints surroundings of pipes and conduit etc complete plinth area of the building at ground floor only shall be measured as per is 6313 part ii 1981 aldrine emulsifiable concentrate or any other approved material such as heptachlor orchlordance will be used the rate of applications of chemical emulsion shall be as follows 1 treatment for masonry and foundation 5 liters per sqm 2 back fill in immediate contract with foundation 7.5 litres per sqm 3 treatment of top surface of plinth filling 5 litres per sqm 4 treatment of soil along external perimeter of building 7.50 litres per sqm 5 treatment of soil under apron along extrnal perimeter 5 litres per sqm 60 providing and injecting for post constructional anti termite treatment 61 providing and fixing 100mm nominal dia circular type ptmt grating of approved quality and colour 62 providing hoisting and fixing at all leads and lift pre cast reinforced cement concrete work in slabs string courses bands copings bed plates anchor blocks plain window sills and the like including the cost of required centering shuttering but excluding cost of reinforcement with 1ratio1 point 5 ratio3 1 cement 1 point 5 coarse sand 3 graded stone aggregate 20 mm nominal size 63 providing and fixing un plasticised 110mm dia pvc pipe clips of approved design to unplasticised pvc rain water pipes by means of 50x50x50 mm hard wood plugs screwed with ms screws of required length including cutting brick work and fixing in cement mortar 1 ratio 4 1 cement 4 coarse sand and making good the wall etc complete 64 providing and fixing on wall face unplasticised pvc moulded fittings accessories for unplasticised rigid pvc rain water pipes conforming to is 13592 type a including jointing with seal ring conforming to is 5382 leaving 10 mm gap for thermal expansion coupler 110 mm dia 65 providing and fixing on wall face unplasticised pvc moulded fittings accessories for unplasticised rigid pvc rain water pipes conforming to is 13592 type a including jointing with seal ring conforming to is 5382 leaving 10 mm gap for thermal expansion single tee with door 110x110x110 mm 66 providing and fixing on wall face unplasticised pvc moulded fittings accessories for unplasticised rigid pvc rain water pipes conforming to is 13592 type a including jointing with seal ring conforming to is 5382 leaving 10 mm gap for thermal expansion single tee without door 10x110x110 mm 67 providing and fixing on wall face unplasticised pvc moulded fittings accessories for unplasticised rigid pvc rain water pipes conforming to is 13592 type a including jointing with seal ring conforming to is 5382 leaving 10 mm gap for thermal expansion bend 87 point 5 degree with or without door 110 mm bend 68 providing and fixing on wall face unplasticised pvc moulded fittings accessories for unplasticised rigid pvc rain water pipes conforming to is 13592 type a including jointing with seal ring conforming to is 5382 leaving 10 mm gap for thermal expansion shoe plain 110 mm shoe 69 providing and fixing ist quality ceramic glazed wall tiles conforming to is 15622 thickness to be specified by the manufacturer of approved make in all colours approved shades of any size as approved by engineer in charge in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1 ratio 3 1 cement 3coarse sand and jointing with grey cement slurry 3 point 3kg per sqm including pointing in white cement mixed with pigment of matching shade complete 70 providing and fixing square mouth sw gully trap class sp1 complete with ci grating brick masonry chamber with water tight ci cover with frame of 300 x300 mm size inside the weight of cover to be not less than 4 point 50 kg and frame to be not less than 2 point 70 kg as per standard design 180x150 mm size p type with common burnt clay fps non modular bricks of class designation 7 point 5 71 providing and fixing pvc floor nahani trap of approved brand and manufacture including making the joint in good condition as per direction of engineer in charge100mm dia 72 providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete 73 providing and fixing factory made upvc door frame made of upvc extruded sections having an overall dimension as below tolerance pluse or minus 1mm with wall thickness 2 point 0 mm pluse or minus 0 point 2 mm corners of the door frame to be jointed with galvanized brackets and stainless steel screws joints mitred and plastic welded the hinge side vertical of the frames reinforced by galvanized ms tube of size 19 x 19 mm and 1mm pluse or minus 0 point 1 mm wall thickness and 3 nos stainless steel hinges fixed to the frame complete as per manufacturers specification and direction of engineer in charge with extruded section profile size 42x50 mm 74 24 mm thick factory made pvc door shutters made of styles and rails of a upvc hollow section of size 59x24 mm and wall thickness 2 mm pluse or minus 0 point 2 mm with inbuilt edging on both sides the styles and rails mitred and joint at the corners by means of ms galvanised plastic brackets of size 75x220 mm having wall thickness 1 point 0 mm and stainless steel screws the styles of the shutter reinforced by inserting galvanised ms tube of size 20x20 mm and 1 mm pluse or minus 0 point 1 mm wall thickness the lock rail made up of h section a upvc hollow section of size 100x24 mm and 2 mm pluse or minus 0 point 2 mm wall thickness fixed to the shutter styles by means of plastic galvanised ms u cleats the shutter frame filled with a upvc multi chambered single code description unit rate no sub head 9 point 0 wood and pvc work 163 panel of size not less than 620 mm having over all thickness of 20 mm and 1 mm pluse or minus 0 point 1 mm wall thickness the panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised ms rod and fastened with nuts and washers complete as per manufacturers specification and direction of engineer in charge for wc and bathroom door shutter 75 supply and fixing of 25 mm dia size frls pvc conduit along with accessories on surface inside the building wall concrete ceiling by a way of cutting slotting of wall throughout pipe length and making good the same with proper cement plastering and painting work required pvc angle all types of jb couplers cement sand paint and miscellaneous items etc are in the scope of contractor only n majority of pvc conduit fixing work is inside the building wall inside concrete roof inside ceilings only 76 supplying and drawing of 4 sqmm frls pvc insulated copper conductor single core cable in the existing surface recess 25 mm pvc conduit proper colour code and cable ferrule shall be maintained at all main distribution sub distribution switch boards loads red yellow blue black green n 30 mtrs per run 77 supplying and drawing of 2 point5 sqmm frls pvc insulated copper conductor single core cable in the existing surface recess 25 mm pvc conduit proper colour code and cable ferrule shall be maintained at all main distribution sub distribution switch boards loads red yellow blue black green n284 mtrs per run 78 supplying and drawing of 1 point 5 sqmm frls pvc insulated copper conductor single core cable in the existing surface recess 25 mm pvc conduit proper colour code and cable ferrule shall be maintained at all main distribution sub distribution swith boards loads red yellow blue black green n450 mtrs per run 79 supply and fixing of good quality of modular gi box electrical graded moduler base and moduler plate for 01 module 80 supply and fixing of good quality of modular gi box electrical graded moduler base and moduler plate for 03 module 81 supply and fixing of good quality of modular gi box electrical graded moduler base and moduler plate for 08 module 82 supply and fixing of good quality of modular gi box electrical graded moduler base and moduler plate for 12 module 83 supply and fixing of good quality of modular gi box electrical graded moduler base and moduler plate for 13 module 84 supply and fixing of 10 amps switch on the existing swith box along with connections etc as required 85 supply and fixing of 10 amps socket on the existing swith box along with connections etc as required 86 supply and fixing of 16 amps switch on the existing swith box along with connections etc as required 87 supply and fixing of 16 amps socket on the existing swith box along with connections etc as required 88 supply and fixing of double mobule stepped fan regulator on the existing switch box along with connections etc as required 89 supply and fixing of blank plate on existing switch board 90 supply and fixing of good quality of ceiling rose along with connections etc as required 91 fixing of bulk head fitting with connections as required 92 supply and fixing of pvc angular type holder including connections as required 93 installation testing and commissioning of any kind of light fitting 94 installation erection and commissioning of ceiling fan wall mount fan along with supply of rod all accessories and hardward kit 95 installation, erection and commissioning of exhaust fans sweep range 350 410 mm along with accessories and hardware kit 96 supply and fixing of 06 way 8 pluse18 distribution box sheet steel type db db contains 02 no of 04 pole tpn 32 amps mcb module 6 nos of single pole mcb module for r phase outgoing ways 6 nos of single pole mcb module for y phase outgoing ways 6 nos of single pole mcb module for b phase outgoing ways db shall have proper bus bar arrangement for neutral and earth points running purpose n1 db contains box base palte module busbars cover and required hardware kit for fixing of same n2 cutting slotting of wall fixing of db cement plasting and painting etc are in scope of contractor only n3 proper colour code shall be followed while make wiring work respectively for r y b phases neutral and earth 97 supply and fixing of 415v 32a 10ka c curve 4 pole mcb tpn in exisiting mcb distribution box 98 supply fixing of 240 415v 10a 10ka c curve 1 pole mcb in exisiting mcb distribution box 99 20 watt led batten tube light 20 watt led batten tube light along with hardware kit 220 240v ac 50hz appx length 1150 mm to 1220 mm luminous efficacy 100 lm per w cool white 20 watt surge protection 2 point 5kv acceptable brands all 100 46 watt exhaust fan metal guard type 46 watt exhaust fan unit along with accessories and hardware kit 230v ac 50hz no of metal blades 04 acceptable sweep range 350410 mm speed 2400 rpm make all brands 101 75 watt ceiling fan along with accessories voltage 230v ac 50hz sweep 1400mm copper winding speed 350 to 400 rpm air delivery range 225 to 250 cmm tyep metal regular colour white make all brands 102 36 watt led flat panel light unit 36 watt led light along with flat panel and all accessories 220 to 240v ac 50hz ai housing with milky diffuser thd lessthan 20 percentage pf geterthan 0 point 9 cri lessthan 80 appx dimensions l x w x d 297 x 297x 10 mm dimension tolerance pluse or minus 5mm galre free uniform light distribution mounting recess pendant cool white 103 100 watt wall mount fan with connected fan regulator min 05 steps of pull cord speed settings input power 220 to 240v ac 50hz copper winding sweep range 600 to 700 100 watt rated fan speed 1000 to 1500 rpm air delivery 40 to350 cubmt per min noof blades03 type of blades aluminium make all brands 104 9 watt high quality led bulb 220 to 240v ac 50hz b22d e27 6500k b22 two pin supportable type make all brands 105 30 watt n type outdoor led light unit wattage 30 w rated voltage 220 240v 50hz lumen efficacy lessthan 100lm per wt thd geaterthan 10percentage pflessthan0 point 95 cri lessthan70 appx dimensions 390 mm x 175 mm fitting bracket dia 90mm ip66 high ingress protection against dust and moisture excellent thermal management ideal heat dissipation with good quality heat sink available in cool white and warm white cct and hardware kit acceptable make all 106 complete bulk head fitting set and suitable 9 watt 2 pin led light bulk head fitting contains body base plate doom holding cage 9 watt b 22 pin supportable lamp holder plastic glass water proof 9 watt led light 230v ac 50hz and suitable hardware kit for fixing of same iec 60598 2 to 4 acceptable brands all 107 supply and fixing of power distribution box out door floor mounting type along with metering unit including of supply of suitable size of service wire and connections pdb shall be made up with mild steel and provided with transparent type front door pdb contains in first compartment 63 amps 4 pole mcb with 5kw 3 phase meter apspdcl approved unit shall be accommodated with proper wiring in second compartment 63 amps 4 pole mccb with protection circuit of overload earth shortcuit fault trip proper indication for supply voltage r y b phases and fault trips shall be given inside the compartment in third compartment 02 no s of 63 ams 4 pole mcb shall be fixed further distribution purpose in forth compartment 01 no of 63 ams 4 pole mcb shall be fixed further distribution purpose note1 proper phase neutral earth bus bar arrangement shall be done note2 pdb shall be made by complying of standard ie code and apspdcl approvals note3 all apspdcl formalities from submitting of an application for new service connection to fixing of pdb is purely in the scope of contractor only note4 for power wiring minimum 06 sqmm frls type copper cable shall be used inside the pdb with proper cable alley path and where as 1 point5 sqmm frls copper cable shall be used for control cabling purpose total quantity : 13419...

Military Engineer Services - Andhra Pradesh

40293828 tender for special repairs to old perimeter wall at bvy visakhapatnam; 1 excavation over areas not exceeding 1.5m deep and getting out in soft / loose soil complete all as specified and as directed.note: the contractor at his option may carryout excavation work using mechanical means wherever required without any extra cost to the department 2 excavation over areas depth exceeding 1.5m and not exceeding 3.0m and getting out in soft / loose soil complete all as specified and as directed.note: the contractor at his option may carryout excavation work using mechanical means wherever required without any extra cost to the department 3 excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m deep and getting out in soft / loose soil complete all as specified and as directed. 4 m & l for crushed stone dust filling under floors or in foundations including watering and consolidation complete all as specified and as directed. 5 m & l for moorum / red bajri filling under floors or in pavings laid in layers not exceeding 15 cm thick, spread levelled and rammed / rolled including watering to required level and gradient complete all as specified and as directed. note:measurements shall be taken after consolidation of earth and 10% deduction shall be made for payments. 6 returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25cm thick of excavated soil complete all as specified and as directed. note: a deduction of 10% shall be made from total computed volume of filling to cater in bulk irrespective of machinery used for ramming. 7 removal of excavated material [ soil ] to a distance exceeding 250m but not exceeding 500m and depositing where directed at a level not exceeding 1.5 m complete all as specified and as directed. 8 m & l for pcc 1:4:8, type d 2, using 40mm graded stone aggregate as in foundation, fillings, mass concrete, footings etc complete all as specified and as directed. 9 m & l for pcc 1:3:6, type c 1, using 20 mm graded stone aggregate as in coping, bed plate, bond stoness, cill and the like including weathering, slightly rounded or chamfered angles and throating including use of necessary formwork [ straight or curved ] complete all as specified and directed. 10 m & l for rcc m 30 design mix, using 20mm graded stone aggregate as in foundations including rafts, footings, foundation beams, plinth beams, bases for columns etc complete all as specified and as directed. 11 m & l for rcc m 30 design mix, using 20mm graded stone aggregate as in columns, pillars, piers, posts and struts etc complete all as specified and as directed. 12 m & l for rcc m 30 design mix, using 20mm graded stone aggregate as in beams, cantilevers, bressummers, lintels etc complete all as specified and as directed. 13 demolition of brick / stone masonry built in cement mortar including all quoins arches pillars etc and removing rubbish to a distance exceeding 1.5 km but not exceeding 5.0 km complete all as specified and as directed. 14 m & l for providing precast cement concrete solid block masonry of 1:3:6, type c1 using 20mm graded stone aggregate exceeding 100mm width with plain or interlocking joints set in cement mortar 1:6 complete all as specified and as directed. 15 m & l for walling of random rubble masonry, uncoursed, well bonded, bedded and solidly hearted, using serviceable stones obtained from demolition, built in cement mortar 1:6 complete all as specified and directed. 16 use and waste of form work to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits [ if any ] of plinth beams and similar work, vertical or to batter for rough finished surfaces complete all as specified and as directed. sides of concrete 17 use and removal of steel formwork to sides of pillars, posts, struts, piers, columns and stanchions of any shape / cross section for rough finished surfaces of concrete complete all as specified and as directed. 18 use and removal of steel formwork to sides and soffits of floor or roof beams, beam launchings, girders, bressummers, lintels, cantilevers, shelves and similar works for rough finished surfaces of concrete complete all as specified and as directed. 19 s & f reinforcement using high strength corrosion resistant deformed tmt bars of grade fe–500d of 10mm dia and over, cut to length, bent to shape required including cranking, bending, spirally for hooping, hooking ends and binding with annealed mild steel wire not less than 0.9mm dia or securing with clips or welded complete all as specified and as directed. 20 s & f reinforcement using high strength corrosion resistant deformed tmt bars of grade fe–500d of 5mm to 10mm dia bars as in stirrups, spacers and binders, cut to length, bent to shape required including cranking, bending, spirally for hooping, hooking ends and binding with annealed mild steel wire not less than 0.9mm dia or securing with clips or welded complete all as specified and as directed. 21 dismantling of mild steel or wrought iron work of any description not otherwise provided for complete all as specified and as directed. 22 s & f mild steel work conforming to fe 290, grade e 165, as in framed work such as grills, gratings, ladders etc with ends of bars shouldered and / or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work complete all as specified and as directed. 23 s & f mild steel work conforming to fe.290.gde e 165 as in framed brackets of angles or teeswith web and flanges cut toshape, drilled and countersunkfor screw, including bending andwelding angles, as necessary, gusset plates, riveting, etc. n exc10 kg each bracket 24 m & l for providing glass coping with 25mm layer of cement mortar 1:3 rendering on top of compound / security walls, with a rounded or weathered finish and firmly embedding broken glass of bottle or thick glass broken to approximately 63mm gauge and firmly embedded into cement mortar at the rate of 10 kg of glass per square metre of rendered surface, jogged edges of the glass being left projecting. 25 s & f galvanised, 2 strand, steel barbed wire 2.24mm dia, barbed with 2mm dia bars at 75mm spacing and straining and fixing to any type of standard rails straining bolts including securing or tying at crossing with and provision of galvanised mild steel wire, staples or steel pins etc complete all as specified and directed.note: each line of wire will be measured for payment. 26 s & f in repairs concertina coil fencing with razor punched barb tape concertina coil made from high tensile spring steel, high carbon wire conforming to is – 4454 [ part – 1 ] , of grade –sm duly hot dipped galvanised, 950mm dia, 10 metre openable length, with galvanised coating and punched tape material as per is – 513, having 50 nos rounds per 6 metre length [ before stretching ] , having medium barbs [ barb length 24±1mm, pitch between two barbs 35±1mm ] , spring core wire [ 2.5 mm thick ] of high tensile strength of 165 kg / sq.mm with tape [ 0.52mm thick ] and weight 43.478 grams / metre and fixing to “y” or trapezoidal shaped angle iron brackets placed at 2.00m to 3.00m apart and with 6 / 9 horizontal rbt [ reinforced barbed tape ] wire, stud tied with gi staples and gi clips to retain horizontal, including necessary bolts and coating with px compound [ anti rust ] complete all as specified and as directed. note: horizontal barbed wire & angle iron supports shall be measured and paid separately under relevant items of schedule a. measurement shall be made for stretched length. 27 taking down cement plaster of any description on brick or stone walls or concrete surfaces etc including raking out joints, hacking for key scrubbing down with water etc and removing rubbish to a distance not exceeding 1.50 km complete all as specified and as directed. 28 m & l for rendering to brick / concrete surfaces, 15 mm thick in cement mortar 1:4, including finishing the top surface even and smooth without using extra cement complete all as specified and as directed. 29 m & l for providing 25mm thick pre formed bitumen impregnated fibre filler board / strip for expansion joints in concrete, conforming to is 1838, cut to size required, placed in grooves, tightly packed all as specified and as directed. 30 m & l for two coats of weather proof exterior emulsion paint [ 100% acrylic ] by using auto roller / airless sprayer over a coat of exterior primer of same manufacturer as that of paint on newly plastered walls / ceiling, pillasters, bands, borders, soffits of chajjas and projections including necessary preparation of surfaces by using vacuum based sanding machine complete all as specified and as directed.note: the contractor shall carryout exterior emulsion painting and allied works under subject work through the authorised applicator of the manufacturer only. the lowest bidder shall submit mou from manufacturer to provide technical support and trained persons for carrying out distempering through their authorised applicatorsbefore commencement of the work to ge for approval. 31 m & l for complete removal of existing treatment of any description on wallsurfaces by using vacuum based sanding machine and applying upto 1mm thick cement based wall care putty by using multipurpose mixture for proper mixing of putty and putty sprayer for application of putty on walls, pillasters, bands, borders, soffits of chajjas and projections including rubbing with sand paper to obtain a smooth surface and making good any undulations on the surfaces and applyingtwo coats of weather proof exterior emulsion paint [ 100% acrylic ] by using auto roller / airless sprayer over one coat of exterior primer on wallsurfaces complete all as specified and as directed.note: the contractor shall carryout exterior emulsion painting and allied works under subject work through the authorised applicator of the manufacturer only. the lowest bidder shall submit mou from manufacturer to provide technical support and trained persons for carrying out distempering through their authorised applicatorsbefore commencement of the work to ge for approval. 32 m & l for one coat of synthetic enamel paint on old painted steel surfaces over 10cm width or girth including preparation of surfaces complete all as specified and as directed. 33 m & l for two coats of synthetic enamel paint over one coat of red oxide / zinc chrome primer on new steel surfaces over 10cm width or girth including preparation of surfaces complete all as specified and as directed....

Nellore Municipal Corporation - Andhra Pradesh

40290067 providing emulsion paint to dividers and islands from madras busstand to kvr petrol bunk and srinivasulu reddy statue to nh5 along gnt road and ayyappagudi junction to bv nagar near tati bellam coffee shop and vanamthopu center to gpr kalyana mandapam of nellore municipal corporation...

Municipal Corporation - Andhra Pradesh

40010255 providing of d.no with three colours (red, black and white) exterior acrylic emulsion paint under nagari naksha in east zone of kadapa municipal corporation...

Municipal Corporation - Andhra Pradesh

40010253 providing of d.no with three colours (red, black and white) exterior acrylic emulsion paint under nagari naksha in north zone of kadapa municipal corporation...

Municipal Corporation - Andhra Pradesh

40010252 providing of d.no with three colours (red, black and white) exterior acrylic emulsion paint under nagari naksha in west zone of kadapa municipal corporation...

Municipal Corporation - Andhra Pradesh

40010251 providing of d.no with three colours (red, black and white) exterior acrylic emulsion paint under nagari naksha in south zone of kadapa municipal corporation...

Rajiv Gandhi University Of Knowledge Technologies - Andhra Pradesh

39999957 supply of painting materials , item=1 acrylic plastic emulsion paint interior grade having voc content less than 50grams / liter ( 20 ltrs can ) with colour, preferred brands: asian tractor shyne ( colour code apricot illusion 7979 ) , nerolac beauty sheen ( colour code inspiration 2058 ) 2 acrylic plastic emulsion paint interior grade having voc content less than 50 grams / liter without colour ( 20 ltrs can ) preferred brands: asian ( colour code ) , nerolac ( colour code ) 3 emery papers ( grit size 80 ) 4 emery papers ( grit size 100 ) 5 emery papers ( grit size 150 ) 6 emery papers ( grit size 240 ) 7 asian paint trucare 9 inch roller set 8 white foam asian paints application 9 inch 9 asian paints 4 inch brush for oil and water based paint 10 asian paints 2 inch brush for oil and water based paint 11 white cement ( 50kg ) 12 aluminum v shape anti skid folding 7 steps ladder 13 damp proof paint ( 20 lit can ) preferred brands: asian ( colour code apricot illusion 7979 ) , nerolac ( colour code inspiration 2058 ) 14 tarpaulin 12ftx15ft plastic cover...

Municipalities - Andhra Pradesh

39487849 supply and delivery of materials for maintenance of community public toilets and e toilets in tirupati town for swachh survekshan 2023. 39.00 supply and transportation of 1x36 / 40w box type tube light luminaire with copper / vpit choke, condensor, starters etc., and 1no 36 / 40w tube etc., complete. ( 4 feet ) 19.00 supply and transportation of 1x36 / 40w box type tube light luminaire with copper / vpit choke, condensor, starters etc., and 1no 36 / 40w tube etc., complete. ( 2 feet ) 12.00 supply, delivery and fixing of led bulbs 9 w including cost and conveyance of all materials, labour charges and laying charges etc., complete. 0.00 supply and delivery of upvc pipe including all labour charges etc complete 120.00 1 upvc pipe 90.00 3 / 4 pvc pipe 45.00 supply and delivery of 3 / 4 cpvc pipe including all labour charges etc complete 3.00 supply and delivery of pvc door including cost and conveyance of all materials, labour charges and laying charges etc., complete. 8.00 supply of 12 ( 300mm ) isi, 900 rpm heavy duty exhaust fan with metallic blades with mark.makes: crompton / almounard / havells turbo force.. ( elec 5.1.13 ) 7750.00 providing and placing on terrace ( at all floor levels ) polythylene water storage tank with double labyer approved brand and manufacture with cover and suitable locking arrangement and making necessary holes for inlet and outlets and over floow pipes but without fittings and base support for tanks 11.00 supplying, installation and commissioning approved make coloured floor mounted ewc ( suit ) cascade model por strap with dual flush porcelain cistern fixed on ewc with al internal parts of dual flush cistern, ultra solid seat cover of approved angle stop cock with wall flanges, ivory gold, all of approvd make etc., complete for finished item of work in all respects. 18.00 supplying and fixing low down porcelain flushing tank 10 lit capacity hindustan sanitary ware / parry / neycer with internal components 7.00 supply and fixing of white glazed flat back bowl urinals of size 440mm x 265 mm x 315 mm with internal flushing rim fixed with screws complete indian make ( hsw / parry / neycer ) conforming to is: 2556 1995 30.00 supply and fixing of tv shape mirror with plastic frame size 609.6 mmm x 457.2 mm 30.00 supply and fixing of towel rings, chrome finish including cost and conveyance of all materials, labour charges and laying charges etc., complete. 14.00 supply, delivery and fixing of pvc tissue roll stand including cost and conveyance of all materials, labour charges and laying charges etc., complete. 40.00 supply, delivery and fixing of pvc wash basin taps ( water tec ) including cost and conveyance of all materials, labour charges and laying charges etc., complete. 31.00 supply, delivery and fixing of pvc flush out taps ( water tec ) including cost and conveyance of all materials, labour charges and laying charges etc., complete. 20.00 supply, delivery and fixing of steel greadings including cost and conveyance of all materials, labour charges and laying charges etc., complete. 6.00 supply, delivery and fixing of gm 3 pin sockets including cost and conveyance of all materials, labour charges and laying charges etc., complete. 165.00 painting with two coats of plastic emulsion paint of apporved brand and shade over a base coat of approved cement primer grade ii making making three coats in all to give an even shade after thoroughly brushing the surface to remove all dirt and remains of loose powdered materials, including cost and conveyance of all materials to work site, scoffolding, curing charges and all operational, incidental, labour charges etc. complete for finished item of work for internal walls ( primer 1 coat used & 2 coats plastic emulsion ) 70.00 flooring with vitrified tiles of 1st quality, set over base coat of cement mortar ( 1:8 ) , 12 mm thick over cc bed already laid or rcc roof slab, including neat cement slurry of honey like consistency spread @ 3.3.kgs per sqm & jointed neatly with white cement paste to full depth mixed with pigment of matching shade, including cost of all materials like cement, sand water and tiles etc., complete, including seigniorage charges, etc., complete for finished item of work, but excluding the cost of conveyance of all materials. 0.00 supply, delivery and fixing of following materials including cost and conveyance of all materials, labour charges and laying charges etc., complete. 47 hand dispencer 47 bathing soap with stand 47 floor cleaner ( sented phenol ) 47 toilet cleaning domex / lizol 47 smooth brooms 47 wapers with stick 47 mopp with stick 47 buckets ( un breakable ) 47 jugs ( un breakable ) 47 litter bins, 20 lit capacity ( out side ) 47 child / disable friendly foam stickers ( size 18 x 18 ) 47 tissue roll 47 air frishners ( quick air ) 5 for electrician ( licensed ) 5 plumber 5 plumber ( helper ) 5 carpenter...

Ministry Of Defence - Andhra Pradesh

39443873 bids are invited for utility annexe and storage space with dimension of 14 feet 26 feet 10 ft separation walls and roof top structure with separation male and female spaces , provision of wall by applying one coat of primer and two coats of birla white or jk wall care putty and applying two coats of royal emulsion paints , flooring with double charged stain free full body porcelain vitrified anti skid tiles of size 800 800 mm with thickness of 10 to 12mm , concealed multiplex fr wiring provision for light fixture modular switches sockets and panel boards metals boxes with accessories for wash room along with multiple connections as per requirement , laying and plumbing for waste water disposal 30 mtrs and fresh water connection 125 mtrs with cost including labour and material , fitment of sanitary fittings along with commodes wash basins with granite slab on top and laying of pipe lines and accessories , fitment of doors and windows for ventilation , manufacturing of heavy duty floor mounted storage utility racks with adjustable shelf of crca material and fr paint scheme and locking facility handles and knobs for easy handling 6ft 4 2 ft...

Municipalities - Andhra Pradesh

39342009 providing electrical materials grills plastering painting to maggala shed 20 and 21 24 rooms at rajeev gruhakalpa 27th ward mangalagiri under municipal general funds 6.62 earthwork in excavation for structures as per drawing and technical specifications clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material as per technical specification 305 mord / 304 morth 1.66 collection, supply and filling of stone crusher dust finer than 3mm with not more than 10% passing 0.075 sieve including cost and conveyance of all materials, labour charges, watering and compacting etc., complete as per ss under bed concrete 1.10 plain cement concrete ( 1:4:8 ) using 40 mm metal with concrete mixture including cost and conveyance of all materials, labour charges, machine mixing charges, curing charges etc., complete as per s.s. 7.94 brick masonry in cm ( 1:6 ) with 2nd class bricks traditional size 23 x 11 x 7 cms including cost of all materials and labour charges for curing and scaffolding charges etc., complete 800.17 plasteing with cm ( 1:4 ) , 12 mm thick including cost & conveyance of all materials and labour charges for mixing and curing etc., complete as per s.s. 774.10 painting to new walls with 2 coats of plastic emulsion paint of approved brand and shade after thouroughly brushing the surface to remove all dirt and remains of loose powdered materials, inlcuding cost and conveyance of all materials to work site and all operational, incidental, labour charges etc., complete for finished item of work as per ss 911 for internal walls. 9225.96 manufacture, supply, delivery and fixing of heavy steel works like trusses, stanchions, heavy beams and girders made with ms structural steel, i.e. angles, channels & i sections etc including welding, finishing, applying red oxide as primary coat etc complete unit 1.00 kgs 50.90 supply and fixing of pre painted galvalume trapezoidal profile roofing sheets with 0.50mm thickness, coating: alu zinc coating az150 gsm. tensile strength: 550 mpa. paint coating: regular modified polyester painting. painting thickness ( top ) : 18 to 20 microns, ( bottom ) : 5 to 7 microns. sheet width: 1.020, length: maximum 12 meters with regular range colours 10 sqm. 1214.24 painting to new iron work with synthetic enamel paint two coats over pirmary coat with red oxide paint including cost and conveyance of all materials and labour charges etc., complete 200.00 manufacture supply and delivery of fixing of 20 gauge u shaped gi sheet with ms angular suitable to said shaped gi sheet including shaping, welding, moulding along with suitable boult and nuts and including all kind of labour charges etc., complete for finished item of directed by the eng incharge...

Rajiv Gandhi University Of Knowledge Technologies - Andhra Pradesh

39058678 supply of painting material, at rk valley campus of rajiv gandhi university of knowledge technologies andhra pradesh=1 acrylic plastic emulsion paint interior grade having voc content less than 50grams / liter ( 20 ltrs can ) with colour, preferred brands: asian tractor shyne ( colour code apricot illusion 7979 ) , nerolac beauty sheen ( colour code inspiration 2058 ) 2 acrylic plastic emulsion paint interior grade having voc content less than 50 grams / liter without colour ( 20 ltrs can ) preferred brands: asian ( colour code ) , nerolac ( colour code ) 3 emery papers ( grit size 80 ) 4 emery papers ( grit size 100 ) 5 emery papers ( grit size 150 ) 6 emery papers ( grit size 240 ) 7 asian paint trucare 9 inch roller set 8 white foam asian paints application 9 inch 9 asian paints 4 inch brush for oil and water based paint 10 asian paints 2 inch brush for oil and water based paint 11 white cement ( 50kg ) 12 aluminum v shape anti skid folding 7 steps ladder 13 damp proof paint ( 20 lit can ) preferred brands: asian ( colour code apricot illusion 7979 ) , nerolac ( colour code inspiration 2058 ) 14 tarpaulin 12ftx15ft plastic cover...

Indian Navy - Andhra Pradesh

38980824 bids are invited for at holiday home utility annexe and storage space with dimension of 14 feet 26 feet 10 ft separation walls and roof top structure with separation male and female spaces , provision of wall by applying one coat of primer and two coats of birla white or jk wall care putty and applying two coats of royal emulsion paints , flooring with double charged stain free full body porcelain vitrified anti skid tiles of size 800 800 mm with thickness of 10 to 12mm , concealed multiplex fr wiring provision for light fixture modular switches sockets and panel boards metals boxes with accessories for wash room along with multiple connections as per requirement , laying and plumbing for waste water disposal 30 mtrs and fresh water connection 125 mtrs with cost including labour and material , fitment of sanitary fittings along with commodes wash basins with granite slab on top and laying of pipe lines and accessories , fitment of doors and windows for ventilation , manufacturing of heavy duty floor mounted storage utility racks with adjustable shelf of crca material and fr paint scheme and locking facility handles and knobs for easy handling 6ft 4 2 ft provisioning of utility annexe with storage space total quantity : 3413...

Andhra Pradesh Medical Services And Infrastructure Development Corporation - Andhra Pradesh

38905169 repairs and renovation to drug store and maternity ot in govt.victoria hospital, visakhapatnam. nos dismantling doors , windows and clear storey windows, ventilators etc., ( wood or steel ) shutters including chowkhats , architraves, hold fasts and other attachments etc., and stacking them within 100m lead including labour charge etc., complete for finished item of work sqm plastering 20mm thick single coat in cm ( 1:5 ) using screened sand including cost and conveyance of all materials like cement, sand, water etc., to site and all operational, incidental charges on materials and including cost of all labour charges for mixing mortar, finishing, curing as directed by engineer in charge etc., complete for finished item of work for floors. ( ss 901, 903 & 904 ) sqm flooring with non skid red or white full body ceramic floor tiles of size 300 mm x 300 mm and thickness between 7 8 mm 1st quality conforming to is:13711, is:13712, is:13630 ( parts 1 to 15 ) of any colour and finish in all shades and designs as approved by engineer in charge, set over base coat of cement mortar ( 1:8 ) , 12mm thick using screened sand over cc bed already laid or rcc roof slab, including neat cement slurry of honey like consistency spread @ 3.3 kgs per sqm & jointed neatly with white cement paste to full depth mixed with pigment of matching shade, including cost of all materials like cement, screened sand , water and tiles etc., and .. complete for finished item of work. ( apss no.701 & 707 ) sqm providing dadooing with glazed red or white full body ceramic wall tiles of size 300 x 450 mm / 320 mm x 400 mm and thickness 6 mm 1st quality conforming to is:13711, is:13712, is:13630 ( parts 1 to 15 ) of any colour and finish in all shades and designs with borders as approved by engineer in charge flushed to wall surface set over base coat of cm ( 1:5 ) 12 mm thick using screened sand with cement slurry of honey like consistency spread at the rate of 3.30 kgs per sqm and jointing with white cement paste mixed with pigment of matching shade to full depth, including cost of all materials like tiles, cement, sand and water etc., complete for finished item of work. sqm flooring with non skid double charged / multi charged stain free full body porcelain vitrified tiles with double layer pigment of size 600 x 600 mm and thickness between 8 10 mm 1st quality conforming to is:13711, is:13712, is:13630 ( parts 1 to 15 ) of any colour and finish in all shades and designs with borders and design as per the approved flooring pattern as directed by the engineer in charge, laying tiles using spacers of 2mm thick, set over a base coat of cm ( 1:8 ) prop. 12mm thick using screened sand over cc bed already laid or rcc roof slab , including neat cement slurry of honey like consistancy spread @ 3.3 kgs per sqm. and jointed neately with white cement paste to full depth mixed with pigment of matching shade including cost and conveyance of all materials like cement, sand, water, tiles, white cement etc., to site ( excluding cost of c.c. bed ) including cost of base coat and all labour charges for mixing of cement mortar, laying tiles to required slope as directed by the engineer in charge etc., complete for finished item of work. ( apss no.701 & 707 ) sqm providing and fixing in true horizontal level 13 mm mineral fiber ceiling tile of 595 x 595 ( square edge fissura fine model ) using hot dipped galvanized steel section exposed surface with pre coated capping, main tee of size 24 x 32 mm at every 1200 mm c / c maximum and rotary stitched cross tee of size 24 x 27 mm at every 600 mm c / c and sub cross tee of size 24 mm x 25 mm at 1200 mm c / c and wall angle of size 19 x 19 mm fixed to periphery of the wall and the above grid is suspended at every 1200 mm c / c in both directions using 2.0 mm thick pre straightened gi wire including cost and conveyance of all materials and labour charges such as cutting , fixing of standing of frame work exposing roof making, etc., complete for finished item of work in all floor in all floors. sqm providing and fixing thermocole false ceiling in true horizontal level 600mm x 600mm using 12mm thick thermocole sheet, anodized aluminium tee sections of size 24.50mm x 24.0mm x 2.4mm in grid with cross tee of size 24mm x 24.5mm at every 600mm center to center and anodised aluminium wall angle of size 24mm x 24mm fixed to periphery of the wall and the above grid is suspended at every 1200mm center to center in both directions using 2.0mm thick gi wire for finished of size 600mm x 600mm including cost and conveyance of all materials and labour charges such as cutting , fixing of standing of frame work exposing roof complete for finished item of work in all floors. sqm providing and applying wall putty of white cement or polymer or cement based of average 1 to 2 mm thickness over plastered surface to prepare the surface even and smooth after thoroughly brushing the surface to remove all dirt and remains of loose powdered materials, applying emery paper, sand the surface, clean & wipe off loose dust, applying knifing paste filler by putty knife / muslin pad, air dry for 2 3 hrs, sand with 180 and 320 no., emery paper for the surface preparation including cost and conveyance of all materials to work site and all operational, incidental, labour charges, etc., complete for finished item of work in all floors for internal walls sqm supply & application of one coat water based cement primer of interior grade i and two coats of acrylic emulsion paint having voc ( volatile organic compound ) content less than 50 grams / litre for internal walls including cost and conveyance of all materials to site, incidental, operational and all labour charges etc., complete for finished item of work in all floors. sqm white washing two coats with white cement to ceiling to give an even shade after thouroughly brushing the surface to remove all dirt and remains of loose powdered materials including cost of all materials , labour charges and incidental such as scaffolding , lift charges etc., complete for finished item of work in all floors. sqm water proofing system with asian paints smartcare 3mm app polyester plain finish membrane surface preparation: dust debris cleaning through wire brush / mechanical grinding / pressure water jetwash .priming: 1 coat of solvent based smart care bitumen primer to be applied with brush / roller at 5 sq m per kg consumption installation of app membrane: supply & application of asian paints smart care 3mm polyester plain finish membrane with butane gas torch ( unit weight – min. 3.0kg / m2 with 600 & 550 n / 5cm of longitudinal & transverse tensile strengths respectively overlaps to be maintained at 100mm and all the laps are to be positioned towards the slope. membrane shall be extended across the vertical height of the parapet wall or at least 600mm to the vertical areas. care to be taken at the anchor points of solar panels / other detailings; the same to be wrapped with hot blown bitumen from the membrane. all application should be as per manufacturer technical data sheet / method statement / specifications sqm painting to wood work and flush shutters with two coats of synthetic enamel paint grade ii voc ( volatile organic compound ) content less than 50 grams / litre of approved brand and shade including cost and conveyance of all materials to site and all labour charges etc. complete complete in all floors ( apss no.1200, 1207 & 1211 ) . sqm supply & application of two coats of acrylic emulsion paint having voc ( volatile organic compound ) content less than 50 grams / litre for internal walls including cost and conveyance of all materials to site, incidental, operational and all labour charges etc., complete for finished item of work in all floors. rmt providing and fixing of pvc shutter frame made with 40mm x 48mm pvc section ( an iso 14001 2015 ) with teak wood reinforcement including labour charges for fixing the frame sqm providing and fixing of 30mm thick pre lam single pvc door made with 20mm pvc panel of door frame 30mm x 100mm with 3 no.s 100mm ss hinges, 2 no.s aluminium aldrops, 1 no. 100mm x 10mm dia towerbolt and 2 no.s 125mm handles including labour charges for fixing shutter etc., complete for finished item of work. nos supplying and fixing european water closet of 1st quality conforming to is:2556 part 2 1973 of white glazed with s trap, supplying and fixing best indian make plastic seat and lid for european water closets with rubber or plastic buffers as per is 2548 1996 and 10 litres capacity single flush pvc low level cistern with internal components and fixed using required size of nails and screws, angle stop cock 12.70mm dia. first quality indian make heavy duty, 12mm pvc connections with brass union nuts cp coated including cost and conveyance of all materials to site, etc., complete for finished item of work for all floors. nos supplying and fixing indian make flat back wash hand basin 1st quality conforming to is:2556 part 4:1972 of size 550mm x 400mm with 32 mm nominal size c.p. fitting with parallel pipe thread conforming to is:2963 1979 and fitted with 15 mm nominal bore chromium plated pillar tap of 1st quality indian make heavy duty complete with standard ci brackets including wooden blocks , 1 no.12.70mm pvc connection with brass union nuts cp coated , angle stop cock 12.70mm dia. first quality indian make heavy duty, 31.75mm dia. pvc flexible waste pipe 914.4mm length of 1st quality including cost and conveyance of all materials to site, labour charges , for finished item of work nos supply & fixing towel rod ( cp ) of 24 long and 3 / 4 dia towel rods with brackets and screws including cost and conveyance of all materials, labour charges , overheads & contractors profit for finished item of work. nos supplying and fixing tv shape mirror with plastic frame of size 609.6mm x 457.2mm , plywood back with np screws 1st quality including cost and conveyance of all materials, labour charges , for finished item of work in all floors. nos s&f 12.7 mm dia np pillar cock heavy duty ist quality etc., including etc., complete indian make seiko / senior / nice or equivalent nos providing and fixing aluminium extruded section body tubular type hydraulic door closer ( is: 3564 ) with double speed adjustment with necessary accessories and screws etc. complete ( type 1: for width of doors up to 700 mm ) as approved by the engineer in charge including cost and conveyance of all materials, labour charges , complete for finished item of work in all floors. rmt supplying and fixing of swr pvc pipes ( prince / sudhakar / kisan / supreme or any isi brand ) 4 kg / sq.cm. and fixing all special such as plain bends, off sets, door bends, single junctions, double junctions as per site requirement, fixing with pvc clamps if necessary with required number of bombay nails including cost and conveyance of all materials to site, labour charges, complete for finished item of work at all floor levels. ( apss no. 1302 1319 & 1326 ) for 75mm dia rmt supplying and fixing of swr pvc pipes ( prince / sudhakar / kisan / supreme or any isi brand ) 4 kg / sq.cm. and fixing all special such as plain bends, off sets, door bends, single junctions, double junctions as per site requirement, fixing with pvc clamps if necessary with required number of bombay nails including cost and conveyance of all materials to site, labour charges, complete for finished item of work at all floor levels. ( apss no. 1302 1319 & 1326 ) for 110mm dia rmt supply and fixing of ashirvad / ajay / astral flowguard or equivalent cpvc pipes and fittings sdr 11 to meet the requirement of astm d 2846 and are produced in cts ( copper tube sizes 1 / 2 to 2 ) for hot and cold water ( is 15778:2007 ) including cost and conveyance of all materials to site, labour charges for fixing, complete for finished item of work at all floor levels. for 22.20mm od pipe rmt supply and fixing of 25mm outer dia ( 1.60 to 1.80 ) mm thicknes medium grade with is:9537 part 3 frls rigid surface p.v.c. pipe ( isi marked ) on wall with all required pvc junction boxes confirms to is : 3419 and all accessories fixing on chromium plated metallic base saddles for run of mains including all labour charges etc., complete. including all labour charges etc., complete. makes : precision / universal& marudhar / vip / goldmedal / million plast / gm / sudhakar / polycab / akg pts wiring with 2 runs of 22 / 0.3mm ( 1.5 sq.mm ) frls / frlsh / hffr / zhfr p.v.c. insulated 1100v grade as per is : 694 / 1990 specification flexible copper cable ( isi marked ) in existing pipe with 6a modular switch ( isi marked ) with cover plate, ceiling rose / bh / sbh, including all labour charges etc., complete for light, bell, fan and exhaust fan points etc., complete. ( for non residential building ) . makes of wires: finolex / rr kabel / havells / kei / polycab / goldmedal / gm / million. makes of switches: legrand ( arteor / myrius ) / schneider ( clipsal x / livia ab ) / crabtree murano or ducor / l&t englaze / gm ( four five ) / goldmedal ( gifa ) / million ( m vee ) nos supply and fixing of 6 amps modular type ( isi marked ) switch, and 6 a 3 / 2 pin modular type socket with cover plate on a common switch board including giving all connections and all labour charges etc., complete. makes of switches / sockets: legrand ( arteor / myrius ) / schneider ( clipsal x / livia ab ) / crabtree murano or ducor / l&t englaze / gm ( four five ) / goldmedal ( gifa ) / million ( m vee ) rmt supply and run of 3 of 2.5 sq.mm ( phase neutral and earth ) frls / frlsh / hffr / zhfr p.v.c. insulated 1100v grade as per is : 694 / 1990 specification flexible copper cable in existing ms conduit pipe for individual ligting circuits including labour charges etc., complete as required for switch boards. makes of wires: finolex / rr kabel / havells / kei / polycab / goldmedal / gm / million rmt supply & run of 3 of 6.0 sqmm ( 84 / 0.3mm ) ( phase neutral and earth ) frls / frlsh / hffr / zhfr p.v.c. insulated 1100v grade as per is : 694 / 1990 specification flexible copper cable in existing ms conduit pipe for run of mains including labour charges etc. complete for ac points & sdbs etc as required. makes of wires: finolex / rr kabel / havells / kei / polycab / goldmedal / gm / million rmt supply & run of 5 of 10.0 sqmm ( phases, neutral and earth ) frls / frlsh / hffr / zhfr p.v.c. insulated 1100v grade as per is : 694 / 1990 specification flexible copper cable in the existing conduict pipe for run of mains from power panel board to tpn dbs with pin type lugs and connections etc., complete. [ for pdbs ] makes of wires: finolex / rr kabel / havells / kei / polycab / goldmedal / gm / million nos supply and fixing of single phase db in sheet steel enclosure as per is 8623; is 13032; iec 61439 3, with metalic plug and socket with 1 no. 20 / 32a, 10ka c curve spmcb control including labour charges and giving connections etc., complete on wall. makes for dbs: legrand ( ekinox 3 ) / schneider acti9 / hager novello+ / seimens / l&t newrange and makes for mcbs: legrand dx3 / schneider acti9 / hager h3 / siemens 5sx4 / l&t au . nos supply and fixing of spn 8 way distribution board with ip 43 protection and as per is 8623; is 13032; iec 61439 3 suitable for single pole outgoing mcbs in sheet steel enclosure with 40a, 10 ka breaking capacity c curve dp mcb as incomer and 6 no of 6 to 32a single pole, 10 ka breaking capacity c curve mcbs as outgoings including making connections etc., complete on wall. makes for dbs: legrand ( ekinox 3 ) / schneider acti9 / hager novello+ / seimens / l&t newrange and makes for mcbs: legrand dx3 / schneider acti9 / hager h3 / siemens 5sx4 / l&t au nos supply, transportation, installation, testing and commissioning of the following inverter model cool type split ac unit with high wall mounted single split indoor unit and outdoor condencing unit hermetically sealed compressor suitable for operation on 230v, 50hz, 1phase ac supply capable of performing heat cool dehumidifying air circulating and filtering with cooling and condensing units with 3 mts of copper piping, insulation kit and 4 mts of 4 core copper flexible chord with cordless remote control etc., dual barrier coating in order to protect coil form oxidigation and with copper condenser.1.5 tr 5 star capable of delivering 18000 btu / hr and above with operating on refrigerant r 32 / r 410a, cop not less than 4.5. makes: blue star pafu dafu series / daikin ftkc50nvm / hitachi nos supply and erecting fully automatic line voltage stabilizer for operation on input voltage 200v to 250v rated for 4 kva maximum load and time delay model with 16a, 3 way connector / socket for output and with 3 core flexible chord and 3 pin 6 / 16a plug top for input suitable for air conditioner for continuous operation including cost and conveyance of all mateials and all labour charges etc., complete. stabilizer makes : v guard / real guard / uni stab / itl nos supply, fabrication of 1set ms bracket suitable for fixing out door unit of split ac unit. nos supply, transportation and fixing of 36w recessed / surface mounting 2 x 2 ( 600x 600 mm ) led luminaire made of crca sheet housing with powder coated with acrylic diffuser, constant current driver as per is: 15885 ( part 2 / sec 13 ) : 2012 , with system lumen output ≥ 3200lm operating voltage range of 150 to 265 volts ac, p.f > 0.9, surge protection: 2kv, thd<10%, with high power leds having efficacy of > 120 lumens / watt, cct: 3000k 5700k, minimum cri>70 etc., complete including fixing in the ceiling with recessed / surface mounting, cost of all accessories and giving connections etc., complete with 5 years warranty. a ) luminaire make : phillips / ge venture / crompton / wipro / bajaj / havells b ) led make : philips lumileds / cree / nichia / osram / samsung / lg...

Indian Bank - Andhra Pradesh

38673124 tender for proposed interior furnishing works for indian bank jujjuru branch 1 partitions: providing and fixing partition in position as per design with 50mmx50mm solid wood finished section frame work @ 600mmc/c both ways screwed to the floor and ceiling with m.s.cleats and to be treated with anti termite oil. the measurement will be taken up to the false ceiling visible height in case of full height partition. the frame work will be claded with 9mm thick bwp grade plywood both sides and to be finished with 1.0mm laminate as per design with approved band adhesive. extra frame work to be fixed for fixing glass. in the glazed partition 12mm thick. modiguard/ saint gobain clear float glass with etching/sand blusting/ granular blasting to be provided duly fixed with white beach/white ceader lipping 50mmx 25mm all complete duly natural polished and melamine finish. in case of full ht partly glazed partition some portion to be raised as per drawing. the work should be completed as per specification, design & approval of the architect. for the door 32mm solid core bwp flush door with a frame work of white beach/white ceader size 75mm x 62.5mm with necessary hold fast fixed to the wall/partition. finished with 1.0mm laminate and lipping in all sides and 40mmx40mm white beach/white ceader wooden molulding to be provided along the periphery of the door frame. supplying and fixing door accessory as door closure, brass hinges, cylindrical/ night latch locks and s.s.handle etc. 1.1 main entrance full glass partition 72.25 sft providing and fixing in position partly glazed full height glazed partition work as shown in the drawings in frame work at 50x100mm thick beach wood frame, glass 12mm thick toughened glass work as shown in the drawings with melamine polish, item including all necessary accessories, all labour charges, all taxes, complete for the finished item of work. 1.2 partly glazed full ht partition at manager cabin 148.00 sft providing and fixing in position partly glazed full height partition work as shown in the drawings including door as shown in the drawings in frame work at 2’ x 2’ grid (horizontally and vertically) comprising of 2” x 2” saal wood section and / or as per frame work shown in the drawings with 9mm thick bwp plywood on both sides finished with 1mm thick laminates of approved shade and colours as shown in drawings. 1.3 solid full height partition at record room & cash counters with grill and doors 289.10 sft providing & fixing in position solid full height double skin partition in frame work including door in 2’ x 2’ grid (horizontally and vertically) comprising of 2” x 2” saal wood section with 9mm thick bwp grade make plywood on both sides finished with 1mm thick laminates of approved make and colour, item to include 2” x 2” sal wood member for door frame. all exposed beech wood surfaces to be finished in melamine polish of matching laminate colour as directed including all necessary stainless steel finish fittings/ hardware, door closers, godrej locks and wood preservative paint etc. as per list of approved material and as approved by the project consultant/ bank officer complete for finished item of work in all respects. 1.4 grill work at cash counter top 69.19 sft aluminium grill – providing & fixing of aluminium grills glazed at cash counter. made out of 2” x 2” hollow square frame section as directed. work includes antirust coat & two coats of first quality enamel paint. all necessary items, all taxes, labour charges, etc., complete for finished of work in all respects. 1.5 solid half ht partition including wicket gate at work stations 88.00 sft providing and fixing wicket gates 4 height with wooden frame work, necessary hardware, lock, hinges and fixing 19mm thick bwp plywood with 1mm thick laminate on both sides of frame. all exposed edges shall be fixed with 12mm thick steam beach wood beading finished with melamine spray polish. 1.6 12mm thk toughened glass 41.50 sft providing & fixing in position 12 mm thick toughened glass at cash counter & work station counters front side, including all necessary items, labour charges, all taxes etc., complete for the finished item of work in all respects. 1.7 cover for rolling shutter at bank 73.00 sft providing, fabricating and fixing cover for rolling shutter made of 2”x2” sal wood frame work spaced at 18” c/c both directions, fixing 19mm thick plywood and 1mm thick laminate (only outside) of approved shade with necessary locking arrangements. separate flap door should be made for rolling shutter to operate. the shutters should be provided with locking arrangement. 2.0 doors 2.1 manager door 42.00 sft providing, fabricating and fixing door frame in 2”x3” steam beach wood and fixing with frame of all round 5 x 2 steam beach wood frame of approved make. the door shall be glazed with 8 mm thick float glass fixed with beach wood beading of 12mm thick and having etching work (etching cost considered @ ` 40/sft). glazing portion of door shall be done in the same line / pattern as of the partition to which it is fixed. all open edges of door shall be leaped with beach wood beading and all wood to be finished with melamine polish. the door shall be fitted with door closer of approved make, 3 nos of heavy brass hinges, brush steel finish 6 lever mortise lock (set of three keys) and heavy door stopper, indian bank logo of approved bank and all other fittings and fixture etc. complete and as per design and approval of engineer in charge. 2.2 branch main entrance door 22.75 sft providing and fixing glass door for entry with 100mmx75mm beech frame wood work duly fixed with the partition/wall with hold fast duly polished. a white beach wood frame work size100mmx50mm as all round frame work with a decorative handle of 600mm of approved brand, floor spring locks, etc all complete. 100mmx50mm thick stiles to be fixed on the frame 3 sides. 12mm thick toughened etched glass and indian bank logo frosted design with necessary sand blasting/granular blasting to be provided and edge should be machine beveled polished. the work to be completed as per design and specification of the architect all complete. the wooden portion to be duly melamine polished. 3.0 tables: providing and fixing in position manger’s table of size 6’ 0” x 3 0”, officer’s table of size 5’ 0” x 2’ 6”, work station table 4 0 x 2 6 including built in storage (credenza) by using 25 mm thick bwp plywood for top and 19mm thick bwp plywood for all other horizontal and vertical members including telescopic cpu stand/ ready made keyboard tray shall be provided of approved model and make. footrest made with t.w. member of size 4” x 1 ½” “finished with french polish. all exposed plywood surfaces to be finished with 1mm thick greenlam make laminate of approved make & shade and all exposed edges of table top & ply verticals to have 1” x ¼” beech lipping. all exposed beech sections to be melamine and internal surfaces to have white enamel paint as directed. item to include plywood boxing, all necessary hardware and fittings in stainless steel finish, lipping to all edges etc. complete for the finished item of work in all respects. 3.1 branch manager (6 0x3 0) 1 no 3.2 w.s table ( 4 0x2 6) 4 no 3.3 server table (4 0x1 6) 1 no 4 side unit 1 nos providing and fixing side unit/back unit made out of 19mm thick bwp ply wood finished with 1.0mm laminate in all exposed areas. the drawers to be made out of 19mm thick make bwp plywood in the front cladded with 1.0mm laminate sides to be made out of 12mm thick bwp plywood and bottom made out of 6mm thick bwp plywood duly painted in matching tone and it should play on drawer sliding channels. the shutters to be made out of 19mm thick bwp plywood and should play on drawer sliding castors on powder coated channels. the necessary locks, handles, etc to be provided. 75mmx12mm wooden skirting to be provided duly polished as per matching tone all along the visible areas. inside of the unit to be enamel painted in matching tone. all the exposed edges of the boards/ plywoods to be covered with wooden lippings/ mouldings duly polished all complete. the work to be completed as per approval and specification of the architect 5.0 cash counter 1 no providing and fixing top, front & side of cash counter made out of 19mmthick bwp plywood as per design cladded with 1.0mm thk laminate on side and front & the edges to be finished with necessary white beach or white ceader lippings, mouldings, etc. special 150mm drawer to be made for the cash with dividers of 12mm thick bwp plywood the front of the drawer made out of 19mm thick bwp plywood finished with 1.0mm laminate, sides 12mm thick bwp plywood and bottom to be made of 6mm thick bwp plywood. the inside and sides of the drawer to be duly polished. the drawers and shutters to be provided with necessary drawer sliding channels, hinges, locks etc. a foot rest to be provided made out of 19mm thk bwp plywood duly polished. inside of the unit to be polished in the matching tone. all visible areas to be covered with white beach of white ceader lippings, mouldings with natural polish. wire manager, cpu trolley, keyboard tray, tea tray to be provided 75mmx12mm white beach white ceader skirting to be provided with natural polish in all visible areas and 18mm thick plain glass to be provided at counter 2nd top customer face. counter top at 1100 mm lvl. the work should be completed as per specification. size: 8 0 x 5 0 x 8 3 6 wall mounted writing ledge: 2 each providing and fixing writing ledge as per design made out 19mm plywood with necessary grove paterns 1.0mm thick laminate (color, vertical grain) to be cladded. small boxes to be made out of 19mm bwp plywoods to be made on top of the writing ledge finished with 1.0mm laminate, inside enamel painted. the work to be completed as per design and approval of the architect. 7 soft board/notice board 1 each providing and fixing soft board with necessary framework with 12mm bwp plywood on top jolly board to be fixed finished with fabric @rs 100, with necessary mouldings duly polished along the periphery. 8 false ceiling 781.00 sft armstrong or equivalent make false celing of trlock sihouette suspension system, providing and fixing in the true horizontal level false ceiling system of armstrong world industries. the suspension system shall be the armstrong. trulock sihouette revealed profile grid system with 15mm wide flanges incorporating 3mm or 6mm central recess colour black revealed silhouette main runners and cross tees to have mitered cruciform junctions. main runners to be spaced at 12mm c/c fixed by using 2mm pre straightened gi wire. main tee, rotary stitched of size 15mm x 38mm x 3000mm at every 1200mm c/c maximum and 600mm c/c cross tee of size 15mm x 38mm x 600mm at every 1200mm c/c maximum and 19mm x 19mm x 3000 wall angel all round the wall to form grid size of 600mm x 600mm and suspending the grid using 2mm prestraightened gi wire and 6mm nylon raw plug at every 1200mm intervals at the maintee laying of armstrong mineral fiber sandfinish (dunemax rh99) tiles manufactured by armstrong world industries of size 600mm x 600mm x 19mm over the formed grid completed as directed, making necessary framework for a.c. ducting, if any, and necessary cutouts for diffusers and light fittings, taping and finishing to proper line & level, including making grooves and trap doors for a.c. unit in 19mm thick bwp grade plywood with stainless steel hinges & locks with moulding 1” x 1” for edges including finishing with white plastic emulsion paint etc. complete in all respects. (note: only the plan area will be measured for payment. no extra payment will be made for cutouts, grooves, mouldings etc.) 9 storages providing and fixing in position back & half height storages using 19mm thick bwp grade plywood of shutters, vertical and bottom, back 6mm thick bwp grade plywood finished with 1mm thick laminates and all other sides shall be finished with white enamel paint as detailed therein. the storage units shall be provided with handles( stainless steel finish )as per approval of the project consultant / bank. all exposed plywood surfaces to be finished with 1mm thick laminate of approved make & shade and all exposed edges of plywood to have 1” x ¼” hard wood lipping. all exposed hard wood sections to be melamine in matching colour laminate and internal surfaces to have white enamel paint as directed. item to include all necessary hardware and fittings in stainless steel finish, godrej multipurpose locks including magnetic ball catcher etc. complete for the finished item of work. 9.1 back storage 15.00 sft 9.2 half height storage 42.00 sft 9.3 full height storage 64.00 sft 10 suggestion/ cheque drop box 2.00 each manufacturing, supplying and fixing of suggestion box made of 19mm plywood and 1.0 mm thick lamination on top as per bank’s specifications 11 running table top 5.00 rft providing & fixing of running table top 1 6 width using of 19mm thick bwp grade plywood finished with 1mm thick laminate, including all necessary items, labour charges, screws, taxes. the work to be completed as per specification and approval of the architect. total of interior furnishing works rs 1 false ceiling – banking hall 12mm thick gypsum board & 12mm thick mineral fiber tile* 1.white 2.india gypsum & armstrong, gyproc, usg ceiling or equivalent* 2 false ceilings cabins 12mm thick mineral fiber tile* 600mm x 600mm 1.white 2. armstrong, gyproc or equivalent 3 partitions frame work: made of 50 x 50mm hard wood like sal wood/hillock or equivalent plywood isi marked and as per is 710, bwp grade (gurjan core) 9mm thick 1. century club prime, 2. green ply gold, 3. archidply classic laminates: 1.0mm thick laminate* 1. fusion maple (wood finish)* 2.formica, 3. euro lam, 4. bravia, green lam, merino or equivalent* 4 counters/tables plywood isi marked and as per is 710, bwp grade (gurjan core), 19mm, 12mm, 9mm thickness archidply classic, century ply club prime, green ply gold or equivalent. laminates:1.5 mm thick for table top and other s 1.0mm thick laminate* 1. fusion maple (wood finish)* century, formica, euro lam, green lam, merino or equivalent* 5 column cladding laminate 1.0mm 1. fusion maple (wood finish)* with regular skirting* century, formica, euro lam, green lam, merino or equivalent* 6 wall painting acrylic emulsion 1.sugarcane asian paints, berger paints, ici, nerolac or equivalent 7 ceiling painting premium emulsion 1.white/ raindrops* asian paints, berger paints, ici, nerolac or equivalent* 8 pinup board for work station fabric 1.maroon velvet or equivalent 9 sofa sets fabric – back & sides 1.maroon visitor seating 1. ss perforated* seated with end arm 10 chairs fabric 1.maroon godrej, wipro, featherlite or equivalent* 11 painting exterior texture – classic or fine* 1.grey – white heritage, spectrum, alltek or equivalent exterior emulsion 1.grey/white asian paints, berger paints, ici, nerolac or equivalent* 12 painting for rolling shutter synthetic enamel paint 1.oxford blue asian paints, ici paints, nerolac or equivalent* 13 vertical blinds fabric* 1.mac, vista or equivalent* 14 doors and windows painting synthetic enamel paint 1.light brown ( sandstone colour) asian paints, berger paints, ici, nerolac etc or equivalent 15 door closer floor spring, door closer hardwin/ everite/ dorma/efficient gadgets. 16 handles for storage, doors brush steel finished of doorset, kitch, kircheff, hatrdwin 17 hinges for doors, storages brass 18 melamine for beading asian in matt finish 19 adhesives for partitions, tables asian trugrip 20 all screws for partitions, tables gkw/ nettle fold 21 patch fitting for doors ebco, godrej, hardwin 22 magnetic catcher for storages mukund 23 wooden beading for partitions, tables, storages steam beech wood. 24 all locks for tables, storages godrej, ebco, doorset for doors, storages....

Department Of Atomic Energy - Andhra Pradesh

38635317 bids are invited for 1 wall painting with acrylic emulsion paint having voc two coats 2 providing and applying white cement based putty of average thickness 1 mm 3 finishing walls with acrylic smooth exterior paint of required shade 4 15 mm cement plaster with mix 1 cement 6 fine sand at all heights and lead as per directions of engineer in charge 5 neat cement punning 6 providing and fixing bright finished brass hanging type floor door stopper with necessary screws etc complete 7 painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade in two or more coats 8 providing and applying plaster of paris putty of 2 mm 9 6mm cement plaster of mix 1 cement 3 fine sand 10 providing and fixing ist quality ceramic glazed wall tiles conforming to is 15622 11 white washing with lime to give an even shade two or more coats 12 clearing and stripping the site of all permanent construction roads pipelines etc including removal of trees 13 supply and transport of earth of specified quality as per specification and drawing 14 earth work in excavation in the following types of soils for all lifts 15 providing and laying in position specified grade of reinforced cement concrete 16 providing and laying in position specified grade of reinforced cement concrete excluding the cost of centering shuttering finishing andreinforcement all work 17 steel reinforcement for rcc work includingstraightening cutting 18 centering and shuttering including strutting propping etc and removalof form for in foundations footings bases of columns etc 19 structural steel work riveted bolted or welded in built up sections trusses and framed work including cutting 20 providing and fixing isi marked flush door shutters conforming to is 2202 21 providing and fixing concertina coil fencing with punched tape concertina coil 600 mm dia 10 metre openable length 22 with gi barbed wire 23 providing and fixing gi chain link fabric fencing 24 removal of wet dry sludge and muck from decant pond channel drain including loading 25 removal of existing damaged glass and fixing of new glass with applying putty 26 welding by gas or electric plant including transportation of plant at site 27 removal of existing damaged doors windows iwc ewc sink or any similar carpentary plumbing and sanitary equipment 28 dismantling colour coated roofing sheets glass reinforced plastic sheets inclusive of gables 29 rectifying all defects causing leakage in pre coated iron profile roofing sheets 30 providing and fixing precoated galvanised iron profile sheets 31 providing and fixing precoated galvanised steel sheet roofing accessories 32 gutter 600 mm over all girth 33 ridges plain 500mm to 600 mm 34 demolishing rcc work by mechanical means and stockpiling at designated locations and disposal of dismantled materials 35 supplying and applying bituminous solution primer on roof and or wall surface 36 random rubble masonry with hard stone in superstructure above plinth level and upto floor five level 37 brick work with common fly ash bricks of class of approved quality 38 providing and injecting chemical emulsion for preconstructional ant termite treatment and creating chemical barrier 39 half brick masonry with non modular fly ash bricks of class designation10 40 providing and fixing white vitreous china pedestal type water closet 41 providing and fixing wash basin with ci brackets 42 providing and fixing 600x450 mm beveled edge mirror of superior glass 43 providing and fixing cp brass bib cock of approved quality conforming to is 44 providing and fixing cp brass stop cock of standard design and of approved make conforming to is 45 providing and fixing water closet squatting pan indian type wc pan with 100 mm sand cast iron p or s trap 46 providing and laying ceramic glazed floor tiles of size 300x300 mm 47 rectifying all defects causing leakage in upvc rain water pipes including pipes 48 cleaning of rain water gutters repair of joints with approved quality jointing compound 49 providing and fixing on wall face un plasticised rigid pvc swr pipes conforming to is 50 providing and placing on terrace polyethylene water storage tank of approved brand is 51 providing and fixing inposition collapsible steel shutters 52 providing and fixing ptmt pillar cock of approved quality and colour 15 mm 53 providing and laying bituminous concrete using crushed stone aggregates 54 sub base course supplying laying spreading and consolidating 125 mm thick 55 base course supplying and laying water bound macadam of 150 mm consolidated thickness 56 providing and fixing aluminium work for doors windows ventilators and partitions with extruded built up standard tubular sections 57 for shutters of doors windows and ventilators including providing and fixing hinges 58 providing and fixing 12 mm thick prelaminated particle board 59 providing and fixing glazing in aluminium door window ventilator shutters and partitions etc 60 with float glass panes of 4 mm thickness 61 providing and fixing brass 100mm mortise latch and dlock with 6 levers without pair of handles 62 providing and fixing aluminium handles 63 providing and fixing aluminium sliding door bolts 64 developing lawn including necessary watering safety expenses manure good earth royalty total quantity : 18048...

Guntur Municipal Corporation - Andhra Pradesh

37845689 providing plumbing, sanitary items, painting and elevation wall art painting to uphc at sanjay gandhi nagar under ae 1 section of guntur municipal corporation. 3818.80 painting with asian apex exterior emulsion multi colour paint two coats over two coats of primery coat of asian exterior emulsion paint and painting of clip art / vector art / 3d double art with enamel paint over old plastered walls of public / govt institutions compound walls medians and islands including cost and conveyance of all materials and lobour charges etc complete including removing of posters and rubbing work for walls up to 10 feet height 27.00 supply and delivery of cement manholes of size .45x0.45 cover for ugd line inspection chambers including cost, conveyance and all charges etc., complete 13.30 supplying for fixing of 75 mm dia. pvc rain water spouts of approved make for 4kg. / sq.cms. of single socket pipe of isi standard with air tight joints, fixing with clams and nails etc., inculding cost and conveyance of all materials to work site labour charges etc for finished item of work inclusive all taxes etc complete 5.00 supply and fixing of premium make cpvc pipes and fittings to meet the requirement of astm d 2846 and are produced in cts ( copper tube sizes 1 / 2 ton 2 ashirvad flowgurard sdr 11 and sdr 13.5 pipes are made from idential cpvc compounds having the same physical properties for hot and cold water ( is 15778:2007 ) 4.00 supply of 32mm ppr tee conforming to din standards 8077 / 8086 ( bmw i.286 ) 5.00 63mm ppr end cap ( bmw i.298 ) 6.00 75 mm dia plain bend 87.5 degree ( bmw g.55 ) 3.00 110mm ppr tee ( bmw i.292 ) 6.00 110 mm dia plain bend 87.5 degree ( bmw g.57 ) 3.00 110mm ppr end cap ( bmw i.301 ) 101.00 22.20mm odpipe sdr 13.5 ( bmw i.221 ) 6.00 s & f gunmetal ( gm ) 25 mm nb size ball valve with ss ball and ss spindle with labour charges ( bmw f.59 ) 4.00 1x1 / 2 inch cpvc tee ( quotation ) 15.00 s & f 25.4 mm holder bat clamps including labour charges only ( bmw f.96 ) 3.00 s & f 38.1 mm holder bat clamps ( bmw f.98 ) 36.40 34.90mm od pipe sdr 11 ( bmw i.229 ) 4.00 s& f31.75mm dia gi bend ist quality ( bmw f.09 ) including labour charges 15.00 p trap ( big with air vent ) 110 mm upvc / swr pipe fittings ( bmw g.110 ) 3.00 country nails ( bmt f.02 ) 2.00 pvc gum ( bill ) 6.00 150 mm dia plain bend 45 degrees ( bmw h.34 ) 4.00 150 mm dia single branch plain t ( bmw h.45 ) 6.00 axa blade ( quotation ) 60.00 supply of 20mm ppr end cap ( bmw i.293 ) 200.00 telfan tape ( quotation ) 20.00 110 mm dia pvc clamp ( quotation ) 4.00 110 mm dia 45 degree bend upvc / swr pipe fittings ( bmw g.63 ) 15.00 110 mm dia 3 m single socket pvc / swr pipe 6 kg / sq.cm ( bmw g.35 ) 2.00 supply of 20mm ppr ball valve conforming to din standards 8077 / 8092 ( bmw i.403 ) 1.00 1 / 2x6pvc nipple ( quotation ) 1.00 1 / 2x4pvc nipple ( quotation ) 1.00 1x1 / 2 inch cpvc brass elbow ( quotation ) 72.00 160 mm dia 3 m double socket pvc / swr pipe 4 kg / sq.cm ( bmw g.32 ) 28.00 1mm dia plain bend 90 degree ( quotation ) 6.00 1 mm dia plain bend 45 degree ( quotation ) 5.00 supply of 25mm ppr tee conforming to din standards 8077 / 8085 ( bmw i.285 ) 2.00 54mm od cpvc pipe sdr 11 ( bmw i.231 ) 2000.00 providing & placing on terrace ( at all floor levels ) polyethylene water storage tank with double layer approved brand & manufacture with cover and suitable locking arrangement & making necessary holes for inlet & outlets and over flow pipes but without fittings & base support for tanks ( bmw g.01 ) 2000.00 labour charges for fixing water storage tank 2.00 1x1 / 2 inch tank nipples ( g.i ) on roof s.s ( quotation ) 2.00 1 1 / 2 x1 cpvc bush ( quotation ) 2.00 1 inch tank nipples on roof s.s ( quotation ) 5.00 1 1 / 2 cpvc coupling ( quotation ) 10.00 1 cpvc coupling ( quotation ) 4.00 supplying & fixing indian makeflat back wash hand basin1st quality conforming to is:2556 part 4:1972 with waste fittings like rubber plug, chain, 32 mm nominal size c.p. fitting with parallel pipe thread conforming to is:2963 1979 and fitted with 15 mm nominal bore chromium plated pillar tap of 1st quality indian make 400 grams seiko / senior / nice / esso or equivalent complete with standard ci brackets including wooden block: 450 x 300 mm double c.p. pillar cock 7.00 s&f 12.7mm n.p bib tap indian make 3heavy duty ( bmw e.09 ) 7.00 wash basin rock bolt 15.00 angle valve ( quotation ) 8.00 nylon connector ( quotation ) 7.00 11 / 4waste tube cupling 5.00 11 / 4waste tube 21.00 toilet rubber seal flange 6.00 s & f cp long body bib cock fancy type deluxe heavy duty 12.7 mm dia indian make ( bmw e.21 ) 7.00 4 steel grating plate 4.00 supply & fixing bib cock cum health faucet with 1 m long flexible tube and wall hook ofjaquar make queen series. ( bmw i.141 ) 2.00 supplying and fixing of europian pan white glazed w.c.of 1st quality conforming to is:2556 part 2 1973 of white glazedwith s trap of isi mark and using with plastic seat and lid for european water closets with rubber or plastic buffers as per is 2548 1996 and also using with low down porcelain flushing tank 10 lit capacitywith internal components , 12.7 mm np stop cock indian makeheavy duty including cost and conveyance of all materials to work site, labour charges etc for finished item of work inclusive all taxes etc complete 2.00 m seal 3.00 nylon pipe 1 mtr long ( quotation ) 30.00 jk white cement 12.00 1 cp extension nipple 1.00 supplying and fixing of orissa pan white glazed w.c.of 1st quality conforming to is:2556 part 3 1981 of white glazedwith s trap of isi mark and using with plastic seat and lid for water closets with rubber or plastic buffers as per is 2548 1996 and also using with low down porcelain flushing tank 10 lit capacitywith internal components , 12.7 mm np stop cock indian makeheavy duty including cost and conveyance of all materials to work site, labour charges etc for finished item of work inclusive all taxes etc complete. 64.05 painting with synthetic enamel paint two coats of approved quality colour & graded i over a primary coat of read oxide paint of grade ii to new steel works after the surface are thoroughly cleaned & scrapped including primary coat item of work, cost & conveyance of all material, labour charges etc. as per s.s & as directed by the departmental authorities for finished item of work 10 sq.m. ( total three coats ) ...

Hindustan Shipyard Limited - Andhra Pradesh

37648025 procurement of material required for r and m works in yard procurement of material required for r and m works in yard , good quality river sand , urinal basin waste pipe (watertec /polo or equivalent) , hand wash basin waste pipe (watertec /polo or equivalent) , 1/2 normal pvc tap (watertec /polo or equivalent) , 2 pvc drain pipe (light gauge) , 2 pvc 45 deg. bends , 1 inch cpvc pipes , cpvc solvent (m seal / ashivador equivalent) 100ml , grey colour emulsion paint , white colour emulsion paint , green colour emulsion paint , signal red emulsion paint , enamel grey paint , enamel blue paint , enamel green paint , enamel yellow paint , enamel black paint , surya cement white wash , emulsion paint brush 6 , emulsion paint brush 5 , painting brush 4 , painting brush 2 , birla white , hacksaw blade 10mm , shellac wood polish , take wood stainer (shellac make) (100ml) , rose wood stainer ( shellac make) (100ml) , emery paper grit 120 (jawan make) , emery paper grit 100(jawan make) , thinner , red brick / country bricks , fresh water tank 1000 ltr capcity (sintex, ashirvad or equivalent)...

Andhra Pradesh Power Generation Corporation Limited - Andhra Pradesh

37540724 procurement of paints required for sdstps township , supply of washable distemper type 2 confirming to is 428:2013, supply of water based cement primer for internal walls confirming, supply of water based cement primer for exterior walls confirming, supply of zinc chromate red oxide primer paint, supply of paint thinner, interior emulsion paint type 1 glossy finish, exterior emulsion paint type 2 semi glossy finish, exterior emulsion paint type 2 semi glossy finish, exterior emulsion paint type 2 semi glossy finish, supply of synthetic enamel paint confirming to is 2932: 2013, supply of synthetic enamel paint, supply of white cement based polymeric putty confirming...

Vijayawada Municipal Corporation - Andhra Pradesh

35679015 providing entry plaza and repairs to play equipments and refurbishment of south side compound wall , toilets in mother theressa park in 13th division in works division iii area. 3.48 dismantling brick work ( cement mortar ) as directed by the dept authorities 0.73 dismantling reinforced cement concrete and prestressed concrete as directed by the dept authorities 2.16 earthwork in excavation for structures as per drawing and technical specifications clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and back filling in trenches with excavated suitable material as per technical specification 305 mord / 304 morth 25.41 supply of sand for filling including cost and coneyance of all materials and labor charges for spreading, sectioning levelling watering etc., complete. 11.88 brick masonry in cm ( 1:6 ) with bricks traditional size 23x11x7 cms 2nd class including cost and conveyance of all materials and labour charges for mixing of mortor watering curing etc. complete. 70.31 supply of precast concrete blocks for paving of m 35 grade and thickness not less than 60 mm for light traffic areas conforming to is 15658:2006 in all shapes and designs as per the manufacturers specification set over the 50 mm thick sand bed with hand roller compaction with joint neatly in homogeneous or heterogeneous pattern as the colour and pattern shall be as per the drawings furnished by the architect, including cost and conveyance of all materials like cement, sand, water, tiles, etc., to site including all operational, incidental, labour charges, laying tiles to required slope as directed by the engineer in charge etc., and overheads & contractors profit complete for finished item of work 96.88 plastering with cm ( 1:4 ) 12mm thick including cost and conveyance labour charges for watering curing etc complete.: 476.00 manufacturing, supply, delivery and fixing of m.s. iron gate , ms grill using with m.s. angulars, m.s. flats including cost and conveyance of all materials and labour charges for cutting, welding, grinding and fixing etc., , complete.as directed by the departmental authorities. 0.00 painting two coats to plastered surface ( external walls ) with plastic emulsion paint grade i to given an even shade after throughly brushing the surface to remove all dirt and remains of losse powdered materials, including cost and conveyance of all materials to work site and all operational incidental labour charges etc., complete for finished item of work as per ss 292.43 plastering qty 13.40 painting with synthetic enamel paints two coats over one coat of zinc chromate yellow oxide primer paint for iron works to given an even shade after throughly brushing the surface to remove all dirt and remains of losse powdered materials, including cost and conveyance of all materials to work site and all operational incidental labour charges etc., complete for finished item of work as per s.s 2.34 flooring with ceramic tiles, set over base coat of cement mortar ( 1:8 ) 7.3 mm thick over cc bed already laid or rcc roof slab, including near cement slurry of honey like consistency spread @ 3.3 kgs per sqm & jointed with neat cement to full depth mixed with pigment of matching shade including cost of all materials like cement, sand water and tiles etc., complete, including complete for finished item of work, but including the cost of conveyance of all materials. 9.30 walling with glazed tiles of thickness 6 mm 1st quality, including near cement slurry of honey like consistency spread @ 3.3 kgs per sqm & jointed with neat cement to full depth mixed with pigment of matching shade including cost of all materials like cement, sand water and tiles etc., complete, including complete for finished item of work, but including the cost of conveyance of all materials. 1.00 supplying & fixing orissa pan white glazed w.c 1st quality isi marked conforming to is:2556 part 3 1981 withp or s trap: 580 mm x 440 mm ( bmw d.04 ) 1.50 providing and fixing 30mm thick brand factory made bothside prelam solid panel pvc door shutter consisting of frame made out of ms. tubes of 19gauge thickness and size of 19mmx19mm for stiles, top and bottom rails. ms. frame shall have a coat of steel primers of approved make and manufacture. ms. frame covered with 5mm thick heat moulded prelam pac ‘c’ channel of size 30mm thickness, 70mm width out of which 50mm shall be flat and 20mm shall be tapered in 450 angle on either side forming stiles; and 5mm thick, 95mm wide prelam pac sheet out of which 75mm shall be flat and 20mm shall be tapered in 450 on the inner side to form top and bottom rail 115mm wide prelam pac sheet out of which 75mm shall be flat and 20mm shall be tapered on both sides to form lock rail. top, bottom and lock rail shall be provided either side of the panel. 10mm ( 5mmx2 ) thick, 20mmwide cross pac sheet shall be provided as gap insert for top and bottom rail. panelling of 5mm thick both side prelam pac sheet to be fitted in the ms. frame welded / sealed to the stiles ( bmt n.03 ) 17.85 collection and supply of gravel for filling including cost and coneyance of all materials and labor charges for spreading, sectioning levelling watering etc., complete. 75.51 supplying, fitting and placing hysd bar reinforcement as per drqwings and technical specifications clauses 1000 and 1202 mord & 1100, 1600 morth for bars below 36mm dia including over laps and wastage, where they are not welded including cost and conveyance of binding wire and preparation and tying grills and fixing in position and labour charges etc., complete 0.00 supply and placing of the rcc m20 ( design mix ) concrete corresponding to is 456 using weigh batcher / 60% of mixer 20mm size graded machine crushed hard granite metal ( coarse aggregate ) 40% of 12mm size graded machine crushed hard granite metal ( coarse aggregate ) from approved quarry including cost and conveyance of all materials like cement, fine aggrregate ( sand ) coarse aggregate, water etc., to site and including seigniorage charges, on all labour charges such as machine mixing, laying concrete, curing etc., complete but excluding cost of steel and its fabrication charges for finished item of work. 0.73 a ) gate colums 0.41 b ) culvert slabs 1.00 providing precasted rcc cement rings of the best quality with 1.20 m dia ( 48 size ) 6 nos and 1no rcc suitable cover including earth work excavation , fixing in position of well rings including cost & conveyance laying of 4size swg pipe from w.c to sump including cost & conveyance of all materials, labour charges for fixing in position as directed by the dept authorities 0.00 providing repairs to children play items by wrought iron and mild steel welded work using angles, ms plates, ss plates etc. including cost of materials and welding rods or bolts and nuts complete fixed in position but without the cost of excavation and concrete for fixing which will be paid separately. 1.00 a ) jumbo sea saw 2 seater : 1.6 long x 9 width, a l angular frame is made with 18 guage ms sheet is fixed tightly by welding and 6mm new polished chains for swing of 50 56 is used. 1.00 b ) jumbo sea saw 2 seater : painting 1.00 c ) butter fly seesa : the seats made with 18 guage ms sheet of size 12x9 in half round shape and handles made with 3 / 4 ms pipes fixed to the a class 7 long pipe and painting with enamal paint over redoxide. ( including welding, fixing and painting charges ) 1.00 d ) butter fly seesa : : painting 1.00 e ) mini atom swing 6 seater : 1.6 long x 9 width, a l angular frame is made with 18 guage ms sheet is fixed tightly by welding and 6mm new polished chains for swing of 50 56 is used. 1.00 f ) mini atom swing 6seater : painting...

Vijayawada Municipal Corporation - Andhra Pradesh

35679014 providing gi chain link mesh fencing , gym play equipments and greenery to removed huts place on krishna rever bund in circle 3 area. 3.00 dismantling / cuttring cement concrete by mechanical means 99.00 earthwork excavation for foundations and depositing on bank for all lifts and with an initial lead of 10m including all operational incidentalm labour charges such as shoring, sheeting, planking, struting, etc, complete for finished item of work including seigniorage exclduing dewatering charges etc, 2.50 providing crusher stone dust for filling including cost and coneyance of all materials and labor charges for spreading, sectioning levelling watering etc., complete. 3.00 providing concrete for plain concrete ( m10 ) using 220 kgs cement , 40 mm nominal size hard stone aggregate , mechanically mixed, placed in foundation and compacted by vibration including curing for 14 days complete as per drawings and technical specifications of morth 10.00 providing concrete for plain concrete ( m20 design mix ) using 330 kgs cement 20 mm, 10mm nominal size graded hard stone aggregate , mechanically mixed, placed in foundation and compacted by vibration including curing for 14 days complete as per drawings and technical specifications of morth 13.50 brick masonry in cm ( 1:6 ) with bricks traditional size 23x11x7 cms 2nd class including cost and conveyance of all materials and labour charges for mixing of mortor watering curing etc. complete. 159.00 plastering in cm ( 1:4 ) 12mm thick including cost and conveyance of all materials, seigniorage charges and labour charges for mixing of mortor watering curing etc. 20.10 walling with high polished granite 16 to 18mm thick slabs other than black set our base coat of cement mortor including neat cement slurry honey light constituency spread at 3.30kgs per sq. and jointed neatly with white cement paste mixed with pigment of matched shade to full depth, including cost of all materials like cement sand water and tiles etc. complete including labour charges for dressing of tiles etc. complete for finished item of work 29.00 halfroundingtheedgesofmarble / granite stone slabs of al lthicknesses including polis hing the same.etc complete as directed by the dept. authorities ( bmm v.10 ) 17.00 providing sand for filling including cost and coneyance of all materials and labor charges for spreading, sectioning levelling watering etc., complete. 580.00 supply, delivery and fixing of of materials ms angulars, m.s flats , square pipes etc including cost and conveyance of all materials to site but excluding cost of fabricarion and fixing labor charges ( c.memo.no.146 / twae / cement &steel / 2020 dated:15 06 2020 ) 25.00 providing ornamental yarrows including cost and conveyance labour charges fixing in possition etc. as directed by departmental authorities 65.00 hot dipped galvanised iron chain link mesh 8 gauge ( 4.0 mm ) as per is: 2721 1979: 3x3 ( 76 mm x 76 mm ) 8 gauge including cost and conveyance of all materials as per s but excluding installation labour charges bmt f.22 200.00 labour charges for fabricating steel works like window grils compound wall grills, lron doors windows including cost of welding rods, power charges, including cost of fixing in position. 33.00 painting with synthetic enamel paint with two coats for new iron work of approved colour and make over 1 coat of primary coat including cost and conveyance of all materials and labour charges etc complete ssr 214.82 painting with plastic emulsion paint grade i ( two coats ) to given an even shade after throughly brushing the surface to remove all dirt and remains of losse powdered materials, including cost and conveyance of all materials to work site and all operational incidental labour charges etc., complete for finished item of work as per ss ( out side ) 180.00 supply, delivery and fixing of rcc bollards of 0.90m height 0.15m dia including cost and conveyance labour charges for fixing in position as directed by the departmental authorities. 1.00 conveyance of excavated earth with an average lead of 5km including loading unloading etc complete as directed by the dept. authorities 75.83 collection supply of red earth for filling including cost and conveyance, spreading, sectioning etc., complete 1.00 thaichi spinner 4 wheel *dimensions: 1230 mm ( l ) x 520 mm ( w ) x 1500 mm ( h ) supply, delivery and commissioning of thai chi spinner 4 wheel with center pipe shall be of minimum 100mm nb dia of thickness not less than 5.00 mm, support frame shall be minimum of 32mm nb dia of thickness not less than 3.6mm & thai chi spinner rings shall be minimum of 25mm nb dia of thickness not less than 3.60mm are of c class heavy grade of tata / jindal make with hot dipped galvanised with minimum of 75 microns zinc dipped joint with robotic welded with handle knobs are made from high quality nylon material. the rings are hinged over 32nb support frame with the help of specially heavy duty bearings should be reputed skf make and press fitted for smooth rotation, and does not require re lubrication i.e., maintenance free ball bearing. all open ends of pipes, bearings, bushes and base cover shall be closed by ss 304 grade stainless steel for safety against entrapment, corrosion & water resistant. all pipes shall be uniformly powder coated with akzonobel up to minimum 100 microns thickness to avoid corrosion. the foundation pipe with anchoring shall be 750mm deep with minimum of 100mm nb dia supported with m.s. angle 24 x 24 x 3.8 mm. the foundation pipe with anchoring shall be 750mm deep with minimum of 100mm nb dia supported with m.s. angle 24 x 24 x 3.8mm. the instruction plate of size 150mm x 230mm of ss 304 grade plate with 0.7mm thick shall be riveted on 5mm thick plate with kakinada smart city corporation emblem and your company emblem at two sides facing to users with laser printing. all nuts, bolts, washers should be of ss 304 material. all products of equipment should be manufactured as per en 16630 safety norms and to be produced proof of valid certificate conformity. 1.00 air walker double *dimensions: 2115 mm ( l ) x 390 mm ( w ) x 1420 mm ( h ) supply, delivery and commissioning of double air walker with three prime stand pipes shall be minimum of 100mm nb dia of thickness not less than 5.00mm, pedestal frame shall be minimum of 32mm nb dia of thickness not less than 3.6mm & handle frame shall be minimum of 25mm nb dia of thickness not less than 3.60mm are of c class heavy grade of tata / jindal make with hot dipped galvanised with minimum of 75 microns zinc dipped joint with robotic welded. the two pedestal frames are hinged over 100nb prime stand pipes with the help of specially heavy duty bearings should be skf make and press fitted for smooth rotation, and does not require re lubrication i.e., maintenance free ball bearing. foot rest shall be made of aluminum material lm26 grade.all pipes shall be uniformly powder coated with akzonobel up to minimum 100 microns thickness to avoid corrosion. all open ends of pipes, bearings, bushes and base cover shall be of ss 304 grade stainless steel for safety against entrapment, corrosion & water resistant. the foundation pipe with anchoring shall be 750mm deep with minimum of 100mm nb dia supported with m.s. angle 24 x 24 x 3.8mm. the instruction plate of size 150mm x 230mm of ss 304 grade plate with 0.7mm thick shall be riveted on 5mm thick plate with kakinada smart city corporation emblem and your company emblem at two sides facing to users with laser printing. all nuts, bolts, washers should be of ss 304 material. all products of equipment should be manufactured as per en 16630 safety norms and to be produced proof of valid certificate conformity. 1.00 triple standing twister *dimensions: 1570 mm ( l ) x 1570 mm ( w ) x 1350 mm ( h ) supply, delivery and commissioning of standing tripple twister with prime pipe shall be minimum of 100mm nb dia of thickness not less than 5.00mm, standing twister plate support pipe shall be minimum of 80mm nb dia of thickness not less than 4.5mm, bottom frame support shall be minimum of 32mm nb dia of thickness not less than 3.6mm & handle ring shall be minimum of 25mm nb dia of thickness not less than 3.60mm are of c class heavy grade of tata / jindal make with hot dipped galvanised with minimum of 75 microns zinc dipped joint with robotic welded. the twister plate is hinged over 80nb standing pipe with the help of specially heavy duty bearings should be skf make and press fitted for smooth rotation, and does not require re lubrication i.e., maintenance free ball bearing. all pipes shall be uniformly powder coated with akzonobel up to minimum 100 microns thickness to avoid corrosion. all open ends of pipes shall be of ss 304 grade stainless steel for safety against entrapment, corrosion & water resistant. the foundation pipe with anchoring shall be 750 mm deep with minimum of 100mm nb dia supported with m.s. angle 24 x 24 x 3.8mm. the instruction plate of size 150mm x 230mm of ss 304 grade plate with 0.7mm thick shall be riveted on 5mm thick plate with kakinada smart city corporation emblem and your company emblem at two sides facing to users with laser printing. all nuts, bolts, washers should be of ss 304 material. all products of equipment should be manufactured as per en 16630 safety norms and to be produced proof of valid certificate conformity. 1.00 chest press double *dimensions: 1600 mm ( l ) x 710 mm ( w ) x 2150 mm ( h ) supply, delivery and commissioning of chest press double with prime stand pipe shall be minimum of 100mm nb dia of thickness not less than 5.00mm, handle frame & seat frame shall be minimum of 32mm nb dia of thickness not less than 3.6mm & connecting links shall be minimum of 25mm nb dia of thickness not less than 3.60mm are of c class heavy grade of tata / jindal make with hot dipped galvanised with minimum of 75 microns zinc dipped joint with robotic welded. the two handle frames are hinged over 100nb prime stand pipe with the help of specially heavy duty bearings should be skf make and press fitted for smooth rotation, and does not require re lubrication i.e., maintenance free ball bearing. seat & back rests are made with the gi sheet of 1.8 mm thickness with dip drawn pressed with uniform bending of 20mm to have free from sharp edges & burrs. all pipes shall be uniformly powder coated with akzonobel up to minimum 100 microns thickness to avoid corrosion. all open ends of pipes, bearings, bushes and base cover shall be of ss 304 grade stainless steel for safety against entrapment, corrosion & water resistant. the foundation pipe with anchoring shall be 750 mm deep with minimum of 100mm nb dia supported with m.s. angle 24 x 24 x 3.8mm. the instruction plate of size 150mm x 230mm of ss 304 grade plate with 0.7mm thick shall be riveted on 5mm thick plate with kakinada smart city corporation emblem and your company emblem at two sides facing to users with laser printing. all nuts, bolts, washers should be of ss 304 material. all products of equipment should be manufactured as per en 16630 safety norms and to be produced proof of valid certificate conformity. 0.00 supply, delivery and commissioning of the following children play equipment of standard brands customized / standard option as preferred by the department including cost and conveyance of materials to site area proposed for installation and commission as per the model image furnished herewith and as directed by the departmental authorities. 1.00 dome climber: arch shaped tubes of 8 feet x 8 feet x 6 feet gi pipes of 60 od; and 32 od ladder stops all pipes of ‘c’ class tata / jindal make powder coated multicolor painting all materials shall confirming to is codes. 1.00 double sea saw with 4 seated ; 8 feet length and 4 feet width 1 – 6” height mounted on central frame structure of 80nb ‘c’ class gi pipes of tata / jindal make and with proper hinges, holders. bolts and nuts, powder coated multi color painting to 60 to 70 microns and seat of high quality lldpe materials – all materials confirming to is codes. 1.00 double arch swing double arch swing of 6.50m x 1.50m size four seated with 6m long 80nb gi pipe bent in single piece and welded together with a flange 5mm their of is 40x40x5mm to form a strong frame bottom and middle height of the frame in 2700mm; top pipe 50nb gi pipe 2950mm length; swing clamp assembly made up of two parts are joined together with m6 allen bolts along with ‘s’ hook to house a bearing for smooth and noiselen swing; rubber dip molded 6 mm dia 1450mm along swing chain; ‘s’ hook of 8mm dia 145 x 130mm triangular hook of ss 304 grade; seats made of lldpe; self lubricated skf / ntn / nachi make bearings; pins and clips of 12mm dia – all framing pipes of ‘c’ class gi pipe of tata / jindal make and powder coated multicolor optional painting of 50 70 micros and all materials shall confirming to is codes. 1.00 6 seater merry go round made of gi frame of ‘c’ class tata / jindal make vertical pipe of 80nb; and framing pipes of 32mm nb & 50mm with ldpe seating base 6 feet dia and powder coated multicolor optional painting of 50 70 microns and all materials shall confirming to is codes. 36.00 manufacture, supply and delivery of unplasicised pvcs pipes for potable water supplies conforming to is : 4985 / 2000 ( 3rd revision ) with bell ends ( socket ) as per specification in light grey / natural ivory grey / any other color ( except white ) inclusive of transportation to the sub divisional stores anywhere in ap excluding excise duty and sales tax etc. 160mm dia pvc pipe 6.00 g / cm^ ( mat 07655 ) 2.00 providing of filter point to 160mm pvc pipe including making charges excluding cost of pipe etc., complete as directed by the departmental authorities 1.00 supply and delivery of 160mm dia pvc dummy including cost and conveyance of work site etc., complete as directed by the departmental authorities 1.00 providing solvent cement / gum 1000ml for the pipe joints and as directed by the departmental authorities. ( bmw g.149 ) 36.00 drilling of bore well with hand bore set to a finished dia of 165 / 175 / 180 mm justify both sides in all kinds of formations suitable for hand bore set drilling such as black cotton soils, sandy and alluvial soils and insertion of pvc / pvc blue casing pipe with couplings including slotting of pipe where ever required and fixing of bore well with cap and bail plug as per directions of the department for a finished item of work including conducting yield test, crew charges, cost of consumables, transportation charges and bore development charges and all other charges required in fixation of pipe assembly, flushing of bore with required pressure excluding cost of all required materials such as cap, bail plug, clamp sets, bolts and nuts etc., excluding all taxes , cost of pvc casing pipe, slotting charges. 1.00 supply and transportation of 1.0hp 5star rated submersible motor pumpset, confirming to is 8034 and motor confirming to is 9283 with water proof winding, pump shall be suitable for various delivery head anddischarge with stainless steel shaft.moor suitable for working on 240v ± 10% , singlephase 50 hz ac supply, etc complete for 4 bore well.makes : as per list of recommended brands as category i. 39.00 supply of 3 core 1.5 sqmm flat copper cable of isi for submersible motors of makes finolex / gm / million / v guard / payal / nakoda / gold medal / hpl / rp etc ( mat 02794 ) 36.00 supply and transportation of outer dia 50mm and inner 38mm dia hdpe duct made as per specification bsen 500 86 / is 14930 part ii. makes:dura line ( dura guard ) or its equivalent make ( mat 03591 ) 1.00 supply and fixing of 32mm x 25mm dia stainless steel nipple. 1.00 supply and fixing of ms clamp set ( 2 nos ) suitable for 32mm dia pipe with 8nos nut & bolts 2.00 s& f31.75mm dia gi bend ist quality including cost and conveyance of all materials etc., complete. 1.00 supply and fixing of 32mm dia g.m non return valve isi make 0.50 s& f 32 mm nominal bore gi pipe medium grade properties & weight as per is 1239isi mark with gi fittings including the cost of pipe & its fittings & labour charges complete ( bmw f.85 ) 12.00 supply of isi 20mm outer dia medium ( 2.1mm thickness ) grade with is:9537 part 3 regid pvc pipe. makes: sudhakar / modi / vip / gm as directed by the departmental authorities ( mat 02673 ) 1.00 fabrication , transportation and supply of suitable size panel board for single phase submersible motor up to 1.5 hp consisting of relay, contactor, starting and running capacitors, voltmeter, ammeter, indicator lamps, mcb , on / off switch. makes: lt lk / bch / crompton / siemens ( elec.5.4.15 ) . 0.00 supply and fixing of premium make cpvc pipes and fittings to meet the requirement of astm d 2846 and are produced in cts ( copper tube sizes 1 / 2 ton 2 ashirvad flowgurard sdr 11 and sdr 13.5 pipes are made from identical cpvc compounds having the same physical properties for hot and cold water ( is 15778:2007 ) 120.00 a ) 28.60mm od pipe sdr 13.5 ( bmw i.228 ) 30.00 b ) 22.20mm od pipe sdr 13.5 ( bmw i.227 ) 0.00 supply and fixing of gm gate valves with as per is 778, class i, indian make heavy type including cost, conveyance of all materials and labour charges etc., complete as per ss. 1.00 a ) 25mm dia ball valves ( bmw f.59 ) 4.00 b ) 20mm dia ball valves ( bmw f.57 ) 4.00 s & f gunmetal gate ( gm peet ) valve as per is 778 class i, indian make heavy type 20 mm nb size etc., complete as directed by the departmental authorities ( bmw f.19 ) 4.00 s& f 20 mm nominal bore gi pipe medium grade properties & weight as per is 1239isi mark with gi fittings including the cost of pipe & its fittings & labour charges complete ( bmw f.81 ) 1.00 amount payable to apspdcl for power charges 280.00 bed preparation for korean / mexican: dressing the surface to the desired shape, laying of 150 mm. ( 6” ) thick fine red garden soil, covered with a thin layer of 10 mm thick sand, watering, rolling ( compacting to 4 thickness by hand roller ) , including the cost of red garden soil, sand and labour charges etc., for complete bed preparation and laying and ramming of lawn mats / rolls in proper position on existing prepared bed by internal transportation from dumped place, including cost of labour for laying, ramming by hand roller / demesha, internal transportation and watering etc., complete for finished item of work excluding cost of grass, fertilizers and chemicals etc., for 1 sqm ( red garden soil in this context it is defined as sandy loamy garden soil congenial for plant growth which shall be of light textured, crystalline, porous and friable, fertile, slightly acidic or neutral ) 54.00 hedge / shrub planting: digging the trench of size 0.3 mtrs. depth, refilling with red garden soil including cost of red garden soil and farmyard manure at 4:1 ratio, internal transportation of plants, planting etc., including the application of fertilizers and pesticides etc., ( @ 20 gms / pit / sqmt ) complete for item of work, but excluding the cost of the fertilizers ( @ 20 gms / pit / sqmt ) and plant material etc., unit 1 sqmt of work. ( * 5 no. / sqm of plants & bag size shall be arrived based on the spacing as per the design. ) ( red garden soil in this context it is defined as sandy loamy garden soil congenial for plant growth which shall be of light textured, crystalline, porous and friable, fertile, slightly acidic or neutral ) 100.00 digging of 0.45x0.45x0.45 mtrs. pit, filling with soil mixture of red garden soil, farmyard manure at 4:1 ratio including internal transport, application of fertilizers and chemicals ( @ 20 gms / pit / sqmt ) , internal transportation of plants, planting the plants etc., for complete item of work ( excluding cost of plant material, fertilizers and chemicals ( @ 20 gms / pit / sqmt ) ) ( red garden soil in this context it is defined as sandy loamy garden soil congenial for plant growth which shall be of light textured, crystalline, porous and friable, fertile, slightly acidic or neutral ) 0.00 supply & delivery of topiary / trees / palms / shrubs / lawn / ground covers and specified plants as per directions of officer in charge at site including cost of plants and conveyance of all materials and labour charges etc., plants of bag size 15 x 16 of plant ( tree / palm / topiary ) height not less than 5 feet, bottom dia of the stem is 0.75 and above, with supporting stick while planting in trench. heights mentioned above are excluding bag height. all the plants supplied shall be with sturdy stem, well formed crown, vigorously growing tip, healthy foliage without any infestation and the plants shall be supplied after proper hardening off. the rates inclusive of loading, transportation to the site, unloading & handling. 450.00 dracaena colorama 400.00 hamelia patens 450.00 cuphea 400.00 heliconia 15.00 bauhinia blackeana violet 15 x 16 15.00 caeslpina pulcherima pink, yellow & red 15 x 16 15.00 callistemon lanceolatus 15 x 16 10.00 callophyllum inophyllum 15 x 16 15.00 lagerstroemia speciosa pink 15 x 16 15.00 millingtonia hortensis 15 x 16 15.00 parijatham 15 x 16 300.00 b ) lawn...

Directorate Of Lighthouses And Lightships - Andhra Pradesh

35432248 tender for development of tourism at pudimadaka lighthouse station. – reg. surface dressing of the groundall kinds of soil including removing vegetation and inequalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m. .including supply of allmaterial, labours, tools & plants safety measures and all other charges etc., complete. 3 providing & laying ofpure green natural lawn grass, color : pure green, type : natural, pile height : 4 10 inch, soil specific : acidic, and neccessity : well watered, full sun exposure, complete all as per directionof engineer in charge.including supply of allmaterial, labours, tools & plants and all other charges etc., complete. 4 providing & fixing of stainless steel modern bf03 bench circular swing, for outdoor playground, with 50mm dia outer pipe, 40mm & 32 mm internal pipes and ss sheets, material : stainless steel, usage / application :outdoor playground, appearance modern, load capacity :150 kg, model name / number:bf03, and surface color coated and fixing of vertical poles in cc 1:3:6, complete all as per directionof engineer in charge.including supply of allmaterial, labours, tools & plants and all other charges etc., complete. 5 providing & fixing ofchildren play equipment ( multi play station ) , specifications: material : ss, steel, pp, frp, wood etc, type : outdoor slide, size: 34x18x18ft and fixing of vertical poles in cc 1:3:6, complete all as per directionof engineer in charge.including supply of allmaterial, labours, tools & plants and all other charges etc., complete. 6 providing & fixing offour seat seesaw vh401kb blue, technical specifications : product code : vh 401kb 10, weight : 60.4 kg, recommended age : 2 10 years, free fall height : 1 m, load capacity : 216 kg, maximum number of users : 4, measurements : 3.68 x 0.29 x 0.88 m, and required area for assembly : 6.7 x 2.3 m and fixing of vertical poles in cc 1:3:6, complete all as per directionof engineer in charge.including supply of allmaterial, labours, tools & plants and all other charges etc., complete. 7 providing & fixing ofred rocking dog stock, as per image and fixing of vertical poles in cc 1:3:6, complete all as per directionof engineer in charge.including supply of allmaterial, labours, tools & plants and all other charges etc., complete. 8 providing & fixing of cast iron garden bench, with backrest, as per image, product details: material: cost iron, seating capacity: 3 seater, length: 4.5, width: 1.5, seating height: 1.5usage / application:complete all as per directionof engineer in charge.including two or more coats of se paint over a primingcoat, supply of allmaterial, labours, tools & plants and all other charges etc., complete. 9 providing & fixing of plants and shrubs, fibre optic grass plant. ... snake plant. ... string of pearls. ... peace lily. ... chinese money plant. ... air plant. ... water bamboo. etc ., .complete all as per directionof engineer in charge.includingpot with se paint , supply of allmaterial, labours, tools & plants and all other charges etc., complete. 10 part b ( water fountain ) 11 earth work in all kinds of soil excavation by mechanical means ( hydraulic excavator ) / manual means over areas ( exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan ) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by engineer incharge., removal of loose soil at bottom, watering , ramming at bottom and as directed by engineer incharge. including cost of all labours, tools & plants and all other charges etc., complete. 12 providing & laying of dry stone pitching 225 mm thick under floors, ramps, septic tank as per drawing and wherever directed with approved quality stone, by proper hand packing, consolidation by rolling / ramming as required filling interstices with spalls and sand all as per standard specifications and as directed, consolidating to required gradient and camber, watering including cost of all labour, materials, tools and plants, safety measures and all other charges etc., complete. 13 providing and laying in position cement concrete infoundation bedwith 1 : 3 : 6 ( 1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size ) all work up to plinth level including laying, compacting, curing as directed by the engineer in charge including cost of all materials, labours, tools & plants, curing, safety measures and all other charges etc., complete. 14 providing and laying 1:1.5:3 ( 1 cement : 1.5 coarse sand ( zone iii ) derived from natural sources : 3 graded stone aggregate 20 mm nominal size de rived from natural sources ) in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement direction of engineer in charge. including cost of all materials, labours, tools & plants, curing, safety measures and all other charges etc., complete. 15 providingsteel reinforcement fe 500d of approved brand for r.c.c. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level andabove plinth level of tested tor steel reinforcement of approved 1st quality as per drawing and as directed at all heights including cost of all labour, materials, tools & plants, safety measures and all other charges etc., complete. 16 providing of centering and shuttering including strutting, propping etc. and removal of form for foundations, footings, bases of columns, etc. for mass concrete, suspended floors, roofs, landings, balconies and access platform, columns, pillars, piers, abutments, posts and struts and stairs, including cost of all labour, materials, tools & plants , safety measures and all other charges etc., complete. 17 20 mm thick cement plaster with cm 1:3 of brick masonry surfaces and concrete surfaces for eexterior plastering up to floor two level, includingand finished even and smooth in cm 1 : 3.as per standard specification and as directed at site including supply of allmaterial, labours, scaffolding, curing, tools & plants, safety measures and all other charges etc., complete. 18 providing and fixing glass mossaic tiles on finished plain wall surface of size 20 mm x 20 mm x 4 mm in all colour, design , fixing in customize design as per direction of engineer in charge. the glass mosaic tiles to be fixed on the wall surface with the help of approved adhesive applied at the rate of 2.5 kg per sqm and grouting of the same. the rate is inclusive of all operation, material and required pattern approved by engineer in charge: 19 providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 ( 1 cement : 4 coarse sand ) , joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. 20 providing & fixing of3 hp open well submersible pump fountain model, complete all as per directionof engineer in charge incl supply of allmaterial, labours, tools & plants and all other charges etc., complete. 21 providing & fixing ofoutdoor control panel box, complete all as per directionof engineer in charge incl supply of allmaterial, labours, tools & plants and all other charges etc., complete. 22 providing & fixing of10 diameter g.i. ring with 60 nos. socket welded, complete all as per directionof engineer in charge including two or more coats of se paint over a primingcoat, supply of allmaterial, labours, tools & plants and all other charges etc., complete. 23 providing & fixing of5 diameter g.i. ring with 44 nos. socket welded, complete all as per directionof engineer in charge including two or more coats of se paint over a primingcoat, supply of allmaterial, labours, tools & plants and all other charges etc., complete. 24 providing & fixing ofbrass adjustable ring nozzle for fountain, complete all as per directionof engineer in charge including two or more coats of se paint over a primingcoat, supply of allmaterial, labours, tools & plants and all other charges etc., complete. 25 providing & fixing of1 brass centre jet nozzle for fountain ( 1 nos ) , complete all as per directionof engineer in charge including two or more coats of se paint over a primingcoat, supply of allmaterial, labours, tools & plants and all other charges etc., complete. 26 providing & fixing ofinterconnecting pvc pipe fittings with control valve for fountain, complete all as per directionof engineer in charge incl allmaterial, labours, tools & plants and all other charges etc., complete. 27 providing & fixing ofrgb under water led light for fountain, complete all as per directionof engineer in charge incl allmaterial, labours, tools & plants and all other charges etc., complete. 28 providing & fixing ofsmps & controller for fountain model, complete all as per directionof engineer in charge incl allmaterial, labours, tools & plants and all other charges etc., complete. 29 providing & fixing ofsolenoid valve ( 5 nos ) fountain model, complete all as per directionof engineer in charge incl allmaterial, labours, tools & plants and all other charges etc., complete. 30 providing & fixing ofsolenoid controller fountain model, complete all as per directionof engineer in charge incl allmaterial, labours, tools & plants and all other charges etc., complete. 31 providing & fixing of 2.5 sqmm 3core underwater copper flat cable, complete all as per directionof engineer in charge incl all material, labours, tools & plants and all other charges etc., complete. 32 providing & fixing of 1.0 sqmm 4 core underwater copper round cable complete all as per directionof engineer in charge incl supply of allmaterial, labours, tools & plants and all other charges etc., complete. 33 providing & fixing ofring stand, light stand, electrical & hardware fitting ( 1 lot ) , complete to make the fountain operational in all respects all as per directionof engineer in chargeincl supply of allmaterial, labours, tools & plants and all other charges etc., complete. 34 part c ( toilet block ) 35 earth work in all kinds of soil excavation by mechanical means ( hydraulic excavator ) / manual means over areas ( exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan ) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by engineer incharge., removal of loose soil at bottom, watering , ramming at bottom and as directed by engineer incharge. including cost of all labours, tools & plants and all other charges etc., complete. 36 providing & laying of dry stone pitching 225 mm thick under floors, ramps, septic tank as per drawing and wherever directed with approved quality stone, by proper hand packing, consolidation by rolling / ramming as required filling interstices with spalls and sand all as per standard specifications and as directed, consolidating to required gradient and camber, watering including cost of all labour, materials, tools and plants, safety measures and all other charges etc., complete. 37 providing and laying in position cement concrete infoundation bedwith 1 : 3 : 6 ( 1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size ) all work up to plinth level including laying, compacting, curing as directed by the engineer in charge including cost of all materials, labours, tools & plants, curing, safety measures and all other charges etc., complete. 38 providing and laying 1:1.5:3 ( 1 cement : 1.5 coarse sand ( zone iii ) derived from natural sources : 3 graded stone aggregate 20 mm nominal size de rived from natural sources ) in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement direction of engineer in charge. including cost of all materials, labours, tools & plants, curing, safety measures and all other charges etc., complete. 39 all works upto plinth level ( foundation ) 40 all works above plinth level upto floor v level ( super structure lintel & column / chajja / roof slab., etc. ) 41 providingsteel reinforcement fe 500d of approved brand for r.c.c. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level andabove plinth level of tested tor steel reinforcement of approved 1st quality as per drawing and as directed at all heights including cost of all labour, materials, tools & plants, safety measures and all other charges etc., complete. 42 filling available excavated earth ( excluding rock ) in trenches, plinth, sides of foundations etc. inlayers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m direction of engineer in charge. including cost of all materials, labours, tools & plants and all other charges etc., complete. 43 supplying and filling in plinth with moorum under floors, including watering, ramming, consolidating and dressing complete.including supply of allmaterial, labours, tools & plants safety measures and all other charges etc., complete. 44 brick work with common burnt clay selected f.p.s. ( non modular ) bricks of class designation 7.5 in exposed brick work including making horizontal and vertical grooves 10 mm wide 12 mm deep complete in cement mortar 1:4 ( 1 cement : 4 coarse sand ) as per drawing and as directed at all heights including cost of all labour, materials, tools & plants, curing, safety measures and all other charges etc., complete. 45 from upto plinth level 46 above plinth level upto floor v level 47 half brick masonrycement mortar 1:3 ( 1 cement :3 coarse sand ) with common burnt clay f.p.s. ( non modular ) bricks of class designation 7.5 in superstructure above plinth level up to floor v level.as per drawing and as directed at all heights including cost of all labour, materials, tools & plants, curing, safety measures and all other charges etc., complete. 48 cement plaster with a floating coat of neat cement 49 20 mm thick cement plaster with cm 1:3 of brick masonry surfaces and concrete surfaces for eexterior plastering up to floor two level, includingand finished even and smooth in cm 1 : 3.as per standard specification and as directed at site including supply of allmaterial, labours, scaffolding, curing, tools & plants, safety measures and all other charges etc., complete. 50 15 mm thick cement plaster with cm 1:3 of brick masonry surfaces and concrete surfaces for interior plasteringfor walls as per standard specification and as directed at site including supply of allmaterial, labours, scaffolding, curing, tools & plants, safety measures and all other charges etc., complete. 51 12 mm thick ceiling plaster with cm 1:3 of brick masonry surfaces and concrete surfaces for interior plasteringfor walls as per standard specification and as directed at site including supply of allmaterial, labours, scaffolding, curing, tools & plants, safety measures and all other charges etc., complete. 52 providing of centering and shuttering including strutting, propping etc. and removal of form for foundations, footings, bases of columns, etc. for mass concrete, suspended floors, roofs, landings, balconies and access platform, columns, pillars, piers, abutments, posts and struts and stairs, including cost of all labour, materials, tools & plants , safety measures and all other charges etc., complete. 53 foundations, footings, bases of columns, etc. for mass concrete 54 columns, pillars, piers, abutments, posts and struts. 55 lintels, beams, plinth beams, girders, bressumers and cantilevers 56 suspended floors, roofs, landings, balconies and access platform. 57 providing & fixing of wpc / pvc frames and shutters for doors and ventilator 58 providing and fixing frame size 65 x 100 mm factory made single extruded wpc ( wood polymer composite ) solid door / window / ceosetory windows & other frames / chowkhat comprising of virgin pvc polymer of k value 58 60 ( suspension grade ) , calcium carbonate and natural fibers ( wood powder / rice husk / wheat husk ) and non toxic additives ( maximum toxicity index of 12 for 100 gms ) fabricated with miter joints after applying pvc solvent cement and screwed with full body threaded star headed ss screws having minimum frame density of 750 kg / cum, screw withdrawal strength of 2200 n ( face ) & 1100 n ( edge ) , minimum compressive strength of 58 n / mm2, modulus of elasticity 900 n / mm2 and resistance to spread of flame of class a category with property of being termite / borer proof, water / moisture proof and fire retardant and fixed in position with m.s hold fast / lugs / ss dash fasteners of required dia and length complete as per direction of engineer in charge. ( m.s hold fast / lugs or ss dash fasteners shall be paid for separately ) . 59 providing and fixing 30 mm thick factory made single extruded wpc ( wood polymer composite ) solid plain flush door shutter of required size comprising of virgin polymer of k value 58 60 ( suspension grade ) , calcium carbonate and natural fibers ( wood powder / rice husk / wheat husk ) and non toxic additives ( maximum toxicity index of 12 for 100 gms ) having minimum density of 650 kg / cum and screw withdrawal strength of 1800 n ( face ) & 900 n ( edge ) , minimum compressive strength 50 n / mm2, modulus of elasticity 850 n / mm2 and resistance to spread of flame of class a category with property of being termite / borer proof, water / moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk s.s screws, all as per direction of engineer in charge. ( note: stainless steel butt hinges and necessary s.s screws shall be paid separately ) 60 providing and fixing factory made door frame ( single rebate ) made out of single piece extruded solid pvc foam profile with homogenous fine cellular structure having smooth outer integral skin having 62 mm width & 32 mm thickness, frame will be mitred & jointed with self driven self tapping screws of size 38 mm x 4 mm & pvc solvent cement, including fixing the frame to wall with suitable dia & length anchor fastener as per manufacturers specification and direction of engineer in charge. 61 providing and fixing factory made 30 mm thick non decorative finish door shutter made of solid pvc foam profile. the styles & rails shall be of size 75 mm x 30 mm having wall thickness 5 mm. the styles, top & bottom rails shall have one side wall thickness of 15 mm integrally extruded on the hingeside of the profile for better screw holding power. the styles and rails shall be reinforced with m.s. tubes of size 33 mm x 17 mmx 1 mm, painted with primer , all four corners of reinforcement to be welded or sealed. solid pvc extruded bidding ( push fit type ) will be set inside the styles and the rails with a cavity, to receive single piece extruded 5mm pvc sheet as panel. the styles and rails will be mitred cut and joint with the help of pvc solvent cement & self driven self tapping screws. single piece extruded solid pvc lock rail of size 100 mm x 30 mm with wall thickness 5 mm & 15 mm integrally extruded in the middle of the lock rail & fixed with styles with the help of pvc solvent cement & self driven self tapping screws of size 100mm x 8 mm complete as per manufacturers specifications and direction of engineer in charge. 62 providing & fixing5.5 mm thick glass louver panes with putty and glazing clips in steel doors, windows, clerestory windows, ventilator, louvers all complete . including cost of all materials, labours, tools & plants, safetty measures and all other charges etc., complete. 63 providingof fittings & fixtures for doors of heavy duty with c.p. brass screws and as directed including cost of all materials, labour, tools & plantsand all other charges etc. complete. 64 providing and fixing 300x16x5 mm bright finished brass door latch with necessary screws etc. complete :including supply of allmaterial, labours, tools & plants and all other charges etc., complete. 65 providing and fixing bright finished 250x10 mm brass tower bolts ( barrel type ) with necessary screws etc. complete. including supply of allmaterial, labours, tools & plants and all other charges etc., complete. 66 providing and fixing bright finished 250x10 mm aluminium tower bolts with necessary screws etc. complete. including supply of allmaterial, labours, tools & plants and all other charges etc., complete. 67 providing and fixing bright finished 125 mm brass handles with screws etc. complete including supply of allmaterial, labours, tools & plants and all other charges etc., complete. 68 providing and fixing 125 mm aluminium handles, isi marked, anodised ( anodic coating not less than grade ac 10 as per is : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : including supply of allmaterial, labours, tools & plants and all other charges etc., complete. 69 providing and fixing bright finished 125x85x5.5 mm ( heavy type ) brass butt hinges with necessary screws etc. completd.including supply of allmaterial, labours, tools & plants and all other charges etc., complete. 70 providing and fixing 125x90x4.00 mmisi marked, is : 1341, m.s. heavy weight butt hinges with necessary screws etc. complete : .including supply of allmaterial, labours, tools & plants and all other charges etc., complete. 71 providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete.including supply of allmaterial, labours, tools & plants and all other charges etc., complete. 72 providing and fixing hard drawn steel wire fabric 75x25 mm mesh of weight not less than 7.75 kg per sqm to window frames etc. including 62x19 mm beading of second class teak wood and priming coat with approved steel primer all complete. including supply of allmaterial, labours, tools & plants and all other charges etc., complete. 73 providing & laying of anti skidceramic floor tiles for bath andglazed wall tiles fortoilets 74 providing and laying rectified glazed ceramic floor tiles of size 300x300 mm or more ( thickness to be specified by the manufacturer ) , of 1st quality conforming to is : 15622, of approved make, in all colours, shades, except white, ivory, grey, fume red brown, laid on 20 mm thick cement mortar 1:4 ( 1 cement : 4 coarse sand ) , jointing with grey cement slurry @ 3.3 kg / sqm including pointing the joints with white cement and matching pigments etc., complete. including supply of all labours, tools, materials and finishing etc. complete as directed by the engineer in charge. 75 providing and fixing ist quality ceramic glazed wall tiles conforming to is: 15622 ( thickness to be specified by the manufacturer ) , of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by engineer in charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand ) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.including supply of allmaterial, labours, tools & plants and all other charges etc., complete. 76 providing and finishing walls with premium acrylic smooth exterior paintwith silicone additives of required shade: for new work ( two or more coats applied @ 1.43 ltr / 10 sqm over and including priming coat of exterior primer applied @ 2.20 kg / 10 sqm ) including cost of all labour, materials, scaffolding, tools and plants etc., complete. 77 providing and finishing walls with 100% premium acrylic emulsion paint for interior wall / ceiling surfaces having voc less than 50 gm / litre and uv resistance as per is 15489:2004, alkali & fungal resistance, dirt resistance exterior paint of required shade ( company depot tinted ) with silicon additives. of new work ( two or more coats applied @ 1.43 litre / 10 sqm. over and including priming coat of exterior primer applied @ 0.90 litre / 10 sqm.including cost of all labour, materials, scaffolding, tools and plants, and all other charges etc., complete. 78 providing and fixing chlorinated polyvinyl chloride ( cpvc ) pipes, having thermal stability for hot & cold water supply, including all cpvc plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes & fittings with one step cpvc solvent cement and testing of joints complete as per direction of engineer in charge. including cost of all labour, materials, scaffolding, tools and plants, and all other charges etc., complete. 79 20 mm dia cpvc pipe 80 25mm dia cpvc pipe 81 32mm dia cpvc pipe 82 40mm dia cpvc pipe 83 providing and fixing ( 6kgf / cm2 ) on wall face unplasticised rigid pvc rain water pipes conforming to is : 13592 type a, including jointing with seal ring conforming to is : 5382, leaving 10 mm gap for thermal expansion, ( i ) single socketed pipes.including cost of all labour, materials, tools and plants, and all other charges etc., complete. 84 110mm dia 85 75mm dia 86 providing and fixing pvc fittings of heavy duty, approved first quality andbrandaccessories like elbow, tee, bend, reducers etc., . including supply of all materials, labours, tools and plants and all other charges etc., complete. 87 p / f.110 mm dia pvc elbow 88 p / f.110 mm dia pvc tee 89 p / f.110 mm dia pvc bend / offset 90 p / f. pvc reducer 110 mm x 75 mm: 91 p / f 110 mm dia pvc floor trap with screen 92 p / f 110 mm dia pvc slotted vent cowl 93 p / f. pvc 110 mm dia door bend 94 p / f. pvc door bend 75 mm dia 95 p / f. pvc 75 mm dia plain bend 96 providing and fixing water supply fittingswith all necessary fixtures and specials of approved first quality brand / manufacturer, colour ( isi make ) as per the following items including cost of all materials, labours, tools & plants and all other charges etc complete. 97 providing and fixing 15 mm nominal bore c.p. brass long nose bib cock conforming to is standards and weighing not less than 810 gms. 98 providing and fixing 15mm nominal bore c.p. brass angle valve for basin mixer and geyser points of approved quality conforming to is:8931. 99 p / fcp brasspillar cock 100 providing and fixing15 mm nominal bore c.p. brass stop cock ( concealed ) of standard design and ofconforming to is:8931. 101 p / f. pvc 15 mm dia flexible connection pipe for w.basin. 102 p / f 20 mm nominal bore ball valve ( brass ) of approved quality, high or low pressure, with plastic floats complete. 103 p / f 25 mm nominal bore ball valve ( brass ) of approved quality, high or lowpressure, with plastic floats complete. 104 p / f 40 mm dia non return valve nominal bore 105 p / f cp waste coupling with 32 mm diapipe 106 health set with hose 107 providing and fixing32 mm diap.v.c. waste pipe for sink or wash basin including p.v.c. waste fittings complete. 108 providing and fixing bath room fittings ofapproved first quality brand / manufacturer, colour / size like mirror, towel rail, soap dish tray with all necessary fixtures including supply of all materials, labours, screws, tools and all other charges etc., complete. 109 providing and fixing 600x450 mm beveled edge mirror of superior glass ( make approved quality ) complete with 6 mm thick hard board ground fixed to wooden cleats with c.p. brass screws and washers complete. eachincluding supply of all materials, labours, screws, tools and all other charges etc., complete. 110 cp brass soap dish 100 mm ( make approved quality ) 111 cp brass towel rail 20 mm dia 600 mm long ( make approved quality ) 112 c.p.brasstowel ring with concealed fittings arrangement of approved quality and colour, where ever necessary 113 providing and placing on terrace ( at all floor levels ) polyethylene water storage tank, is : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. including cost of all materials, labours, tools & plants and all other charges etc., complete. 114 providing and fixing white vitreous china orissa pattern w.c. pan of size 580x440 mm with integral type foot rests water closet squatting pan ( indian type w.c. pan ) with 100 mm sand cast iron p or strap, 10 litre low level white p.v.c. flushing cistern, including flush pipe, with manually controlled device ( handle lever ) conforming to is : 7231, with all fittings and fixtures complete, including cutting andmaking good the walls and floors wherever required:and all other charges etc., complete. 115 providing and fixing white vitreous china pedestal type water closet ( european type ) with seat and lid, 10 litre low level white vitreous china flushing cistern & c.p. flush bend with fittings & c.i. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : with all fittings and fixtures complete, including cutting and making good the walls and floors wherever requiredand all other charges etc., complete.. 116 providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and c.p. brass spreaders with brass unions and g.i clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : including painting of fittings and brackets, cutting and making good the walls and floors wherever required : 117 providing & fixing of urinals partition board and g.i clamps complete, including fittings and brackets, cutting and making good the walls and floors wherever required : including supply of allmaterial, labours, tools & plants and all other charges etc., complete. 118 providing and fixing wash basin with c.i. brackets, 15 mm c.p. brass pillar taps, 32 mm c.p. brass waste of standard pattern, ( make parryware, hindware ) including painting of fittings and brackets, cutting and making good the walls wherever require: white vitreous china wash basin size 630x450 mm with a pair of 15 mm c.p. brass pillar taps.including supply of allmaterial, labours, tools & plants and all other charges etc., complete. 119 constructing soak pit 1.20x1.20x1.20 m filled with brickbats including s.w. drain pipe 100 mm diameter and 1.20 m long complete as per standard design.including supply of allmaterial, labours, tools & plants and all other charges etc., complete. 120 constructing brick masonry chamber for underground c.i. inspection chamber and bends with bricks in cement mortar 1:4 ( 1 cement : 4 coarse sand ) c.i. cover with frame ( light duty ) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg ( weight of cover 23 kg and weight of frame 15 kg ) , r.c.c. top slab with 1:1.5:3 mix ( 1 cement : 1.5 fine sand : 3 graded stone aggregate 20 mm nominal size ) , foundation concrete 1:5:10 ( 1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size ) , inside plastering 12 mm thick with cement mortar 1:3 ( 1 cement : 3 coarse sand ) , finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design.inside dimensions 455x610 mm and 45 cm deep for single pipe line.with common burnt clay f.p.s. ( non modular ) bricks of class designation 7.5. including supply of allmaterial, labours, tools & plants and all other charges etc., complete. 121 diluting and injecting chemical emulsion for post constructional anti termite treatment including the cost of chemical emulsion including cost of all labour, materials, tools & plants etc., and other charges complete. 122 treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 ( 1 cement : 2 coarse sand ) to match the existing floor: with chlorpyriphos / lindane e.c. 20% with 1% concentration including supply of all labours, tools, finishing etc. complete as directed by the engineer in charge. 123 along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc., with chlorpyriphos / lindane e.c. 20% with 1% concentration. including supply of all labours, tools, finishing etc. complete as directed by the engineer in charge. 124 supplying chemical emulsion in sealed containers including delivery as specified.chlorpyriphos / lindane emulsifiable concentrate of 20% including supply of all labours, tools, finishing etc. complete as directed by the engineer in charge. 125 providing & fixing ofelectric workincluding supply of all labours, tools, finishing etc. complete as directed by the engineer in charge. ( u / g cable from ph to new building, light fittings, wiring cables with pipe, etc., ) ( detail breakup of electrical items is enclosed in the tender document ) 126 providing & fixing ofkent ro water purifier, capacity: 10 15 l, filter cartridges: activated carbon, installation type: wall mounted, purification type: ro, uf, tds controller, purifier type:electric and purification capacity ( per hour ) 15 l / hr, including supply of all labours, tools, finishing etc. complete as directed by the engineer in charge. 127 part d ( parking area ) 128 earth work in all kinds of soil excavation by mechanical means ( hydraulic excavator ) / manual means over areas ( exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan ) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by engineer incharge., removal of loose soil at bottom, watering , ramming at bottom and as directed by engineer incharge. including cost of all labours, tools & plants and all other charges etc., complete. 129 supplying and laying of 63 mm to 45 mm size stone aggregate, spreading and compacting stone aggregate of specified sizes to wbm specifications in uniform thickness, hand picking, rolling with 3 wheeled road / vibratory roller 8 10 tonne capacity in stages to proper grade and camber, applying and brooming requisite type of screening / binding material to fill up interstices of coarse aggregate, watering and compacting to the required density . and as directed by engineer incharge. including cost of all labours, tools & plants and all other charges etc., complete. 130 providing and laying in position cement concrete infoundation bedwith 1 : 3 : 6 ( 1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size ) all work up to plinth level including laying, compacting, curing as directed by the engineer in charge including cost of all materials, labours, tools & plants, curing, safety measures and all other charges etc., complete. 131 painting road surface marking 10cm width new work ( two or more coats ) with adequate nos of coats to give uniform finish with ready mixed roadmarking paint conforming to is : 164, on bituminous / concrete surface in white / yellow shade, including cleaningthe surface of all dirt, scales, oil, grease and foreign material etc. complete. 132 providing of centering and shuttering including strutting, propping etc. and removal of form for foundations, footings, bases of columns, etc. for mass concrete, suspended floors, roofs, landings, balconies and access platform, columns, pillars, piers, abutments, posts and struts and stairs, including cost of all labour, materials, tools & plants , safety measures and all other charges etc., complete. 133 part e ( pathway ) 134 earth work in all kinds of soil excavation by mechanical means ( hydraulic excavator ) / manual means over areas ( exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan ) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by engineer incharge., removal of loose soil at bottom, watering , ramming at bottom and as directed by engineer incharge. including cost of all labours, tools & plants and all other charges etc., complete. 135 supplying and laying of 63 mm to 45 mm size stone aggregate, spreading and compacting stone aggregate of specified sizes to wbm specifications in uniform thickness, hand picking, rolling with 3 wheeled road / vibratory roller 8 10 tonne capacity in stages to proper grade and camber, applying and brooming requisite type of screening / binding material to fill up interstices of coarse aggregate, watering and compacting to the required density . and as directed by engineer incharge. including cost of all labours, tools & plants and all other charges etc., complete. 136 providing and laying in position cement concrete infoundation bedwith 1 : 3 : 6 ( 1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size ) all work up to plinth level including laying, compacting, curing as directed by the engineer in charge including cost of all materials, labours, tools & plants, curing, safety measures and all other charges etc., complete....

South Central Railway - Andhra Pradesh

34863589 supply of paint enamel synthetic golden yellow finishing isc 356 to i.s:8662 / 2004 with rdso amendment no. 1 ( rev. 0 ) for pigment content as an additional requirement to is: 8662 2004 w.e.f. 01.08.2016, and icf specn. no. icf / md / spec 045 issue 02 rev. no.03 and rdso%u2018s amendment no. 1b as an additional requirement. packing: packed in new steel drums plain ( non returnable ) 20 ltrs.cap.is:2552 / 89 gr.b2.and colour code to is:5 / 2007 make berger or asian or emulsionpaint enamel synthetic golden yellow finishing isc 356 to i.s:8662 / 2004 with rdso amendment no. 1 ( rev. 0 ) for pigment content as an additional requirement to is: 8662 2004 w.e.f. 01.08.2016, and icf specn. no. icf / md / spec 045 issue 02 rev. no.03 and rdso%u2018s amendment no. 1b as an additional requirement. packing: packed in new steel drums plain ( non returnable ) 20 ltrs.cap.is:2552 / 89 gr.b2.and colour code to is:5 / 2007 make berger or asian or emulsion, paint enamel synthetic golden yellow finishing isc 356 to i.s:8662 / 2004 with rdso amendment no. 1 ( rev. 0 ) for pigment content as an additional requirement to is: 8662 2004 w.e.f. 01.08.2016, and icf specn. no. icf / md / spec 045 issue 02 rev. no.03 and rdso%u2018s amendment no. 1b as an additional requirement. packing: packed in new steel drums plain ( non returnable ) 20 ltrs.cap.is:2552 / 89 gr.b2.and colour code to is:5 / 2007 make berger or asian or emulsion => limited...

Indo Tibetan Border Police Force - Andhra Pradesh

34413407 annual repair maintenance of non residential building civil works for the year 2022 23 at 56th bn itbp, visakhapatnam. sh acrylic exterior wall paint and interior wall plastic emulsion paint...

Hindustan Shipyard Limited - Andhra Pradesh

33849977 procurement of materials for n1 quarter procurement of materials for n1 quarter , domestic plumbing & sanitary accessories , domesticpaints & hardware accessories 1 110mm pvc plain bends 2 110mm pvc 45 degree bends 3 110mm pvc tees 4 110mm gi clamps of good quality 5 china nails 1 1 / 2 6 110mm pvc cowl 7 wash basins 500x400mm size 8 wash basins waste coupling ss 1 1 / 4 9 1st quality ss pillar taps 10 rock bolt sets 11 european water closet 12 6 lits flush tanks 13 1 / 2x2 length connectors 14 ss angle cocks 15 ss two way bib cock 16 ss health faucet 17 ss washing machine tap 18 ss long body tap 19 ss short body tap 20 shower rose 100mm 21 brass concealed valves 22 stainless steel a isi 304 ( 18 / 8 ) kitchen sink of size 610x510 mm bowl depth 200mm 23 ss sink waste coupling ( 1 1 / 2 ) 24 waste pipe 25 ss extension nipple 1 1 / 2 26 ss extension nipple 1 27 cp flanges 28 teflon tapes 29 cpvc gum 118 ml 30 75mm pvc pipes 31 75mm plain bend pvc 32 75mm pvc tees 33 pvc solvent 250ml 34 100mm ss floor trap ( jali ) 35 hdpe 1000 ltr. capacity water tank 36 01 brass float valve set 37 01 tank nipple gi 38 01ball valve brass 39 01 union upvc40 4 way cross cpvc 41 15mm cpvc pipe 42 15mm cpvc elbows 43 15mm brass elbows pvc 44 15mm plain cpvc tee 45 15mm brass tee cpvc 46 15mm cpvc socket 47 15mm cpvc unions 48 15mm cpvc mabt 49 15mm cpvc fabt 50 75mm door bend pvc 51 75mm pvc door tee 52 110mm pvc pipe of 10feet length 53 110mm pvc door bend 54 110mm pvc door tees 55 25mm upvc pipes of 10feet length 56 25mm upvc elbows 57 25mm upvc tee 58 25mm upvc sockets 59 25mm upvc unions 60 25mm upvc fabt 61 25mm upvc mabt 62 25mm upvc valves 63 25mm upvc clamps1 wall putty 40kgs bags 2 premium quality acrylic interior emulsion paint ( milk white ) 3 wall primer 4 synthetic enamel paint ( snow white ) 5 red oxide primer 6 wood primer 7 wood putty 8 paint rollers 9 inch 9 paint rollers 4 inch 10 2 paint brush 11 ss tower bolts 4 inch 12 ss handles 4 inch 13 ss tower bolts 6 inch 14 hanging floor rubber door stopper 15 3 inch ss handles 16 snowcem ( blue colour ) 17 putty blade set 18 3 / 4 star black screws ( 500 nos ) 19 1 star black screws ( 500 nos ) 20 1 1 / 2 star black screws ( 500 nos ) 21 ss soap dish holder 22 ss towel rail 600mm length 23 ss coat hook 6 eye...

Military Engineer Services - Andhra Pradesh

33523723 provision of deficient sailors married accommodations at certain places at visakhapatnam 1 surface dressing not exceeding 15 cm deep and getting out in soft / loose soil complete all as specified and as directed. 2 rough excavation not exceeding 1.5m deep and getting out in soft / loose soil complete all as specified and as directed. 3 excavation in trenches not exceeding 1.5m wide and not exceeding 10 sq.m on plan area and not exceeding 1.5m deep in soft / loose soil complete all as specified and as directed. 4 excavation in trenches not exceeding 1.5m wide and not exceeding 10 sq.m on plan area and depth exceeding 1.5m but not exceeding 3.0m and getting out in soft / loose soil complete all as specified and as directed. 5 removal of excavated material [ soil ] to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and as directed. 6 removal of excavated material [ soil ] to a distance exceeding 250 m but not exceeding 500m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and as directed. 7 returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25cm thick of excavated soil complete all as specified and as directed. note: a deduction of 10% shall be made from total computed volume of filling to cater in bulk irrespective of machinery used for ramming. 8 m & l for pcc 1:4:8, type d 2, using 40mm graded stone aggregate as in foundation, fillings, mass concrete, footings etc complete all as specified and as directed. 9 m & l for rcc m–30 design mix, using 20mm graded stone aggregate as in foundations including rafts, footings, foundation beams, plinth beams, bases for columns etc. complete all as specified and as directed. 10 use and removal of steel formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits [ if any ] of foundation and plinth beams and similar work, vertical or to batter for rough finished surfaces complete all as specified and as directed. 11 m & l for rcc m 30 design mix, using 20mm graded stone aggregate as in columns, pillars, piers, posts and struts etc. complete all as specified and as directed. 12 use and removal of steel formwork to sides of pillars, posts, struts, piers, columns and stanchions of any shape / cross section for rough finished surfaces of concrete complete all as specified and as directed. 13 m & l for rcc m 30 design mix, using 20mm graded stone aggregate as in beams, cantilevers, bressummers, lintels over 1.5m span etc complete all as specified and as directed. 14 use and removal of steel formwork to sides and soffits of floor or roof beams, beam launchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc, splays between floors and beams and similar works for rough finished surfaces of concrete complete all as specified and as directed. 15 m & l for rcc m 30 design mix, using 20mm graded stone aggregate as in slabs supported on walls, beams, columns, landings, shelves and the like complete all as specified and as directed. 16 use and removal of steel formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work not exceeding 200mm thick [ horizontal or sloping ] including rough finished surfaces complete all as specified and directed. 17 s & f reinforcement using high strength corrosion resistant deformed tmt bars of grade fe–500d of 10mm dia and over, cut to length, bent to shape required including cranking, bending, spirally for hooping, hooking ends and binding with annealed mild steel wire not less than 0.9mm dia or securing with clips or welded complete all as specified and as directed. 18 s & f reinforcement using high strength corrosion resistant deformed tmt bars of grade fe–500d of 5mm to 10mm dia bars as in stirrups, spacers and binders, cut to length, bent to shape required including cranking, bending, spirally for hooping, hooking ends and binding with annealed mild steel wire not less than 0.9mm dia or securing with clips or welded complete all as specified and as directed. 19 s & f gi wire cloth / mesh with2 mm dia of wire and fixed with tinned tacks or stainless steel wire staples as in lateral reinforcement for pre fabricated concrete wall panels / modules all as per manufacturers instructions, as specified and as directed. 20 m & l for providing pre fabricated reinforced concrete wall panels / modules with hollow infill patterns, light weight with acoustic properties duly factory fabricated through computer aided automated 3d printing technology with desired models / patterns / logos, etc. as per the drawings provided by the engineer in charge for the building. the pre fabricated 3d wall panels shall be cast off site in layer by layer with layer thickness of 15 20mm each and layer width of 30 35mm, including transportation from off site to on site, installed and assembled in position all as per manufacturers instructions, as specified and as directed.notes: [ a ] the pre fabricated reinforced concrete wall panels / modules with any sort of design as per the drawings provided shall be procured and installed through specialist firms viz. m / s. micob pvt ltd., ( gandhi nagar, gujrat ) / m / s. tvasta manufacturer solutions pvt ltd. ( chennai ) . necessary mou shall be entered with any of the specialist manufacturer as mentioned above to provide technical support and to provide trained persons for supervision of the work and the same shall be submitted alongwith the tender documents [ t bids ] . if any tenderer fails to produce mou, their bid shall be rejected and their financial bid shall not be opened. [ b ] an authorised person of the specialist manufacturer of the panels shall be made available by the contractor at site for co ordination with the department as well as with the off site manufacturing unit for smooth execution of the work including supervision of work at site at every stage of work without hampering the desired progress of the work. [ c ] the size and shape of the panels shall vary according to the site requirement during execution of the work and the contractor shall be required to quote the rate accordingly and nothing extra shall be allowed on this account. [ d ] the contractor shall submit necessary design details and requisite manufacturers test certificates in respect of the 3d printed wall panels / modules prior to incorporation of the same at site. 21 [ e ] the fabrication of concrete 3d printed wall panels shall be commenced only after conforming the strength parameters of the walls with respect to m 30 design mix strength. the composition of materials for 3d printed walls shall be as follows: ( i ) opc 53 grade cement ( not less than 550 kg / cum ) ( ii ) fly ash ( not less than 300 kg / cum ) ( iii ) quartz m sand ( not less than 1000 kg / cum ) ( iv ) silica fumes / fibers to improve the buildability, extrudability and flowability ( not less than 180 kg / cum ) ( v ) water ( not less than 300 litres / cum ) ( vi ) super plasticizers viscosity modifying agent ( not less than 35 litres / cum ) ( vii ) galvanised steel wire mesh with 2mm dia wires as in lateral reinforcement placed in horizontal position at every 300mm height to increase tensile and flexural strength. ( viii ) fe 500d anti corrosive tmt reinforcement bars shall be used as main reinforcement with 30mm nominal cover in semi automatic method of 3d printing without hampering the printing speed. [ spacing of bars shall be as per the detailed drawing provided at the time of execution ] [ f ] all safety measures shall be ensured while transportingthe wall panels from off site to on site and the wall panels shall be transported only after attaining the target mean strength in accordance with m 30 design criteria. [ g ] each wall panel shall be provided with suitable anchorage for lifting and installing in position. suitable capacity of crane, trailer, lifting arrangements shall be provided by the contractor for handling of the panels at both off site and on site. [ h ] the weight of each panel / module shall not exceed 700 kg. [ i ] the wall panels shall be with 40% rustic finish. 22 [ j ] the panels shall be compatible to mechanical, electrical and plumbing systems to be accommodated in the building and accordingly the panels shall be fabricated in the factory as per the drawings provided or as directed by the engineer in charge as per site requirement. [ k ] the tmt bars provided as main reinforcement and wire mesh provided as lateral reinforcement shall be measured and paid separately under relevant items of this schedule / boq. [ l ] the contractor shall submit psmb duly marked with the location for record. [ m ] site visit to the manufacturer’s workshop / factory shall be made by the departmental executive staff authorized by the accepting officer during fabrication of wall panels and at the time of delivery of each lot to check the manufacturing process and to determine the strength parameters of the panels. [ n ] quality assurance plan shall be submitted by the contractor to the accepting officer for approval within 15 days from the date of commencement. 23 [ o ] the contractor shall furnish a written guarantee to ge from the specialist firm engaged by him for a period of 25 years from the certified date of completion by the ge for the effectiveness of the 3d printed wall panels supplied and installed in the subject work on non judicial stamp paper of ? 100.00. during the aforesaid guarantee period of 25 years, the contractor shall be solely responsible for the effectiveness of the 3d printed wall panels. any sign of cracks or defects of any type noticed by the ge during this period shall be promptly rectified by the contractor without any extra cost to the government. the above provision shall not however, absolve the contractor of his responsibility of effectiveness of the 3d printed wall panels as required under the provisions of contract. should the ge, at any time during construction or reconstruction or prior to the expiration of guarantee period of 25 years after the 3d printed wall panel work has been completed as per contract, finds that any building / structure showing any sign of cracks or defects of any type, the contractor shall, on demand in writing from the ge specifying the location complained of notwithstanding that the same may have been inadvertently passed / certified and paid for, forthwith undertake to carry out such treatment as may be necessary to render the structure [ s ] free from cracks or defects at his own expenses for a period of 25 years from the certified date of completion. in the event of his failing to do so, within the period as specified by the ge in his demand aforesaid, the ge may undertake such rectifications as may be necessary through other agency at the risk and expense in all respects of the contractor. the liability of the contractor under this condition shall not extend beyond the period of 25 years from the certified date of completion, unless the ge had previously given notice to the contractor. 24 [ p ] a security deposit against the guarantee period for effectiveness of the 3d printed wall panels supplied and installed in the subject work for 25 years shall be calculated @ 5% of the amount of 3d printed wall panels priced at contract rates and shall be retained by the government from the contractor’s dues. this amount shall be refunded to the contractor after the expiration of the guarantee period of 25 years from the certified date of completion by the ge, provided always that the contractor shall first have been paid the final bill and have rendered no demand certificate [ iafa – 451 ] . alternatively, the contractor may furnish fixed deposit receipt in lieu of security deposit from a schedule bank in favour of ge for the above said guarantee period. condition 10, 46 & 68 of general conditions of contracts [ iafw – 2249 ] shall be deemed to be amended to the extent mentioned above. [ q ] any minor constructional details not specified elsewhere but which are essential for execution and completion of work including all incidental charges shall also be deemed to be considered by the contractor and the rate quoted shall be deemed to include for all the above provisions no extra claims shall be allowed by the department. 25 m & l for 40 mm thick pcc 1:2:4, type b 0, using 12.5mm graded aggregate as in padding over roof slabs, surface finished fair and even without using extra cement complete all as specified and as directed. 26 m & l for preparing the surfaces of concrete roof and brushing neat cement slurry with 3.0 kg of cement per sq.m area, rendering 10mm thickin cement mortar 1:3 on concrete surfaces finished even and smooth without using extra cementincluding mixing of water proofing compound of approved make as per manufacturers instructions for levelling the surface smooth to receive the water proofing membrane, priming the surface with a coat of cold applied bituminous primer @ 0.50 kg per sq.m, applying a coat of blown bitumen of grade 85 / 25 @ 1.2 kg per sq.m, laying polymeric water proofing membrane of weight not less than 3.00 kg per sq.m reinforced with polyester non woven fabric of weight notless than 150 grams per sq.m, by torch application with side over lap of 100mm & end over lap of 150mm & tucked into the chases on vertical surfaces by thermo fusion including applying a coat of blown bitumen of grade 85 / 25 @ 1.2 kg per sq.m and finished with a coat of bituminous aluminium paint @ 100 grams per sq.m on top for water proofing treatment completecomplete all as specified and as directed. note: water proofing compound will be measured and paid separately. 27 m & l for rendering to brick / concrete surfaces, 10 mm thick in cement mortar 1:6, surfaces finished even and smooth without using extra cement complete all as specified and as directed. 28 m & l for rendering 5mm thick in cement mortar 1:4 including mixing water proofing compound as per manufacurers instructions over a backing coat of 10mm thick in cm 1:6 on concrete or brick masonry surfacesand finishing the top surface even and smooth without using extra cement complete all as specified and as directed.note: water proofing compoundwill be measured and paid separately. 29 supply only integral water proofing compound [ isi marked ] of approved make. 30 m & l for rendering 5 mm thick in cement mortar 1:3 on fair faces of concrete surface of ceiling surfaces finished even and smooth without using extra cement complete all as specified and as directed. 31 demolition of cement concrete of any description and in any position not otherwise specifically provided for and removing rubbish to a distance not exceeding 1.50 km complete all as specified and as directed. 32 m & l for two coats of weather proof exterior emulsion paint [ 100% acrylic ] by using auto roller / airless sprayer over a coat of exterior primer of same manufacturer as that of paint on newly plastered walls / ceiling, pillasters, bands, borders, soffits of chajjas and projections including necessary preparation of surfaces by using vaccume based sanding machine complete all as specified and as directed. 33 m & l for preparing newly plastered ceiling surfaces and applying threecoats of white washing complete all as specified and as directed. 34 m & l for preparing newly plastered wall surfaces by using vaccume based sanding machineandapplying two coats of acrylic washable distemper by using auto roller / airless sprayer, over a coat of alkali resistant primer over two or more coats of cement based wall care putty on walls by using multipurpose mixture for proper mixing of putty and putty sprayer for application of putty including rubbing with sand paper to obtain a smooth surface and making good any undulations on the wall surfaces complete all as specified and as directed. 35 m & l for vitrified tiles, double charged, coloured, premium quality, of size not exceeding 0.36 sq.m, 10 mm thick as in floors, set and jointed in cement slurry and pointed flush using polymer based cementitious tiling joint filler to match the shade of the tile including screed bed or bedding layer of mortar 15 mm thick in cement mortar 1:4 complete all as specified and as directed. note: the colour / shade / design of tiles shall be as approved by ge. 36 m & l for vitrified tiles, double charged, coloured, premium quality, of size not exceeding 0.36 sq.m, 10 mm thick as in skirting and dado, set and jointed in cement slurry and pointed flush using polymer based cementitious tiling joint filler to match the shade of the tile over backing coat of 10mm thick in cement mortar 1:3 complete all as specified and as directed. note: the colour / shade / design of tiles shall be as approved by ge. 37 m & l for non skid ceramic tiles, joint free, coloured, premium quality of size exceeding 0.11 sq.m and not exceeding 0.18 sq.m, 7 to 8 mm thick [ square or rectangular ] as in floors etc, set and jointed in neat cement slurry and pointed flush using polymer based cementitious tiling joint filler to match the shade of the tile including screed bed or bedding layer of mortar 15 mm thick in cement mortar 1:4 complete all as specified and as directed. note: the colour / shade / design of tiles shall be as approved by ge. 38 m & l for joint free glazed ceramic tiles, edge cut, concept type, coloured, premium quality, of size 450 mm x 300 mm, 7 to 8 mm thick as in vertical surfaces such as skirting, dado etc set and jointed in neat cement slurry and pointed flush using polymer based cementitious tiling joint filler to match the shade of the tile over backing coat of 10mm thick in cement mortar 1:3 complete all as specified and as directed. note: the colour / shade / design of tiles shall be as approved by ge. 39 s & f gi water tubing of 15 mm bore, medium grade conforming to is 1239 [ part 1 ] including all fittings such as bends, tees, short pieces, connectors, elbows, reducers, union, sockets etc fixed to walls, ceiling or laid on floors including testing complete all as specified and as directed. 40 s & f gi water tubing of 20 mm bore, medium grade conforming to is 1239 [ part 1 ] including all fittings such as bends, tees, short pieces, connectors, elbows, reducers, union, sockets etc fixed to walls, ceiling or laid on floors including testing complete all as specified and as directed. 41 s & f gi water tubing of 25 mm bore, medium grade conforming to is 1239 [ part 1 ] including all fittings such as bends, tees, short pieces, connectors, elbows, reducers, union, sockets etc fixed to walls, ceiling or laid on floors including testing complete all as specified and as directed. 42 s & fvitreous china wash down water closet [ pedestal pattern ] , white, including 10 litres capacity, pvc valve less, syphonic action type, low level flushing cistern, white, with inlet ball valve, float, handle, flush pipe of polyethylene of lowor high density of pvc, 32mm dia, pvc connection of 15mm bore and 600mm long with ptmtcheck nut and union etc. including brackets and connections to pipe and flush pipe including plastic water closet seat back closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging device and p or s trap complete all as specified and as directed. 43 s & fvitreous china ware wash hand basin, white, flat back of size 450 mm x 300 mm including pillar taps, cast copper alloy, chromium plated, fancy type, 15 mm dia, with capstan head, screwed down high pressure with or with out lettered hot or cold with long screwed shanks and fly nuts screwed for iron pipe and fixed, 32mm dia brass chromium plated waste fittings with long screw shanks and fly nuts, flange end bedded in red led cement and other end fixed, rubber plug with rings including ci brackets, cutting for and pinning in ends of brackets or erecting strand, 32mm bore pvc flexible waste pipe, pvc connection of 15mm bore and 600mm long with ptmt check nut and union etc. complete all as specified and as directed. 44 s & fbib taps, 15 mm dia, brass chromium plated, fancy type with crutch or butterfly handle, screwed down for iron pipe and fixed etc. complete all as specified and as directed. 45 s & fstop valves, 15 mm dia, cast copper alloy with capstan head, chromium plated, fancy type, screwed down high pressure with crutch or butterfly handle with long shank and cup [ concealed type ] for iron pipe etc complete all as specified and as directed. 46 s & fangle cock, 15 mm dia, cast copper alloy with capstan head, chromium plated, screwed down high pressure with crutch or butterfly handle for iron pipe etc. complete complete all as specified and as directed. 47 s & f ptmt tubular towel rail, 20mm dia, d type, 600 mm long between flanges, fixed with and including chromium plated brass screws and wooden / plastic cleats [ minimum weight 190 grams ] complete all as specified and as directed. 48 s & f ptmt soap dish with screws complete all as specified and as directed. 49 s & f rotational moulded polythene [ hdpe ] water tanks, triple layered, isi marked, cylindrical & vertical type 1000 litres capacity hoisted and fixed in position including provision of 40mm / 25mm dia spouts for connecting inlet, outlet, over flow and washout pipes complete all as specified and as directed. 50 s & f ball valves, 25 mm bore, high pressure of ptmt with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe [ minimum weight 25mm 455 grams ] etc complete all as specified and as directed. 51 s & f gun metal globe or gate valve of class i, pressure tested of 1.5 mpa, 25 mm bore with iron wheel head, screwed both ends for iron pipe, conforming to is, isi marked complete all specified and as directed. 52 m & l for 40mm bore dia high density polyethylene pipes [ hdpe of pressure rating 6 kgf / sq.cm laid in trenches or fixed to walls or ceilings or in floors etc. complete all as specified 53 s & f 75mm bore pvc [ swr ] pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and as directed. 54 s & f 75mm outlet pvc [ swr ] floor trap with grating including jointing with solvent cement complete all as specified and as directed. 55 s & f 110mm bore pvc [ swr ] pipes single socketed, in any length with rubber ring joints, fixed to walls including necessary brackets, clamps complete all as specified and as directed. 56 s & f 75 mm bore pvc [ swr ] bends of any radius including jointing with solvent cement complete all as specified and as directed. 57 s & f 110 mm bore pvc [ swr ] bends of any radius including jointing with solvent cement complete all as specified and as directed. 58 s & f 75 mm bore pvc [ swr ] branch piece, single [ singley ] equal or unequal jointing with solvent cement complete all as specified and as directed. 59 s & f 110 mm bore pvc [ swr ] branch piece, single [ singley ] equal or unequal jointing with solvent cement complete all as specified and as directed. 60 s & f 110mm bore pvc [ swr ] gully trap with grating including jointing with solvent cement complete all as specified and as directed. 61 m & l for hardcore of gauge not exceeding 63mm of broken stones or boulders, deposited, spread and levelled in layers not exceeding15 cm thick watered and rolled with power road roller of 8 to 12 ton capacity and consolidated to required gradient and camber complete all as specified. 62 m & l for 75 mm thick, pcc 1:3:6, type c 1, using 20mm graded stone aggregate as in plinth protection, surfaces finished even and smooth complete all as specified and as directed. 63 s & f solid pvc door frame of size 50mmx47mm made out of 5mm plain colour pvc sheet reinforced with ms square tube in opening complete all as specified and as directed. 64 s & f factory made solid panel pvc door shutter 30 mm thick [ style ] consisting of frame made out of m.s. tubes for top & bottom rails. m.s. frame shall be covered with heat moulded plain colour pvc c channel having a pvc sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour pvc sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour pvc sheet to be fitted in the m.s. frame welded / sealed to the stiles & rails with suitable pvc sheet beading, and joined together with solvent cement fixing in frame at site as per specification complete all as specified and as directed. 65 m & l forpowder coated aluminium sections [ minimum 50 micron thick ] of approved colour as in door, window, ventilator frames, partitions with one or more rebates and door, windows shutters sliding / openable type / ventilator shutter aluminium section including necessary joining cleats, glazing clips, neoprene rubber packing, powder coated aluminium snap beading, screws and locking arrangements complete all as specified and as directed. note: [ a ] the size of aluminium sections shall be all as specified in relevant is code and mes schedule part i. [ b ] supply only panel inserts of glass / gauze / grills will be measured and paid separately. [ c ] unit rate quoted shall be deemed to include for cost of rubber beading, glazing clips, neoprene packing and fixing only of panel inserts ofglass / gauze / grills etc. 66 s & f 75mm size, butt hinges, stainless steel, medium weight, bright polished including fixtures complete all as specified and as directed. 67 s & f aluminium anodised handle, of extruded section fabricated type of size 75mm long complete all as specified and as directed. 68 s & f aluminium anodised barrel tower bolt of size 100 mm size of extruded section complete all as specified and as directed. 69 supply only powder coated aluminium deco grill of model / design no. dg 104 ( 7.2mmx4.2mm ) including powder coated aluminium channel of size 30 x 12 x 1.5mm for fixing deco grill complete all as specified and as directed. 70 supply only 5mm thick sheet glass ordinary quality in squares exceeding 0.5 sq.m in each pane complete all as specified and as directed. 71 supply only 4mm thick figured glass and glazing with oil putty or with wooden beads in squares not exceeding 0.5 sq.m in each pane complete all as specified and as directed. 72 supply onlystainless steel wire cloth / mesh with average aperture not exceeding 1.40 mm and dia of wire 0.36 mm complete all as specified and as directed. 73 s & f stainless steel wire cloth / mesh with average aperture not exceeding 1.40 mm and dia of wire 0.36 mm complete all as specified and as directed. 74 m & l for plain cement concrete type c1 [ nominal mix ] 1:3:6 using 20mm graded stone aggregate cast in situ in lintels up to 1.5m span, cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings up to 60 cm in height, copings, kneelers, apex stones, bed plates including weathering, slightly rounded or chamfered angles and throating as directed including use and waste of form work, complete all as specified and as directed. 75 m & l for two coats of synthetic enamel paint over one coat of pink primer to newly untreated wooden surfaces over 10cm width or girth including preparation of surfaces complete all as specified and as directed. 76 s & f mild steel work conforming to fe 290, grade e 165 as in bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required, hooks [ stay ] , heavy, for large gates, hook and pintle hinges, large hasps and staples, chains, hand made sliding bolts, clamps, hold fasts, wall ties, hooks for hanging fans, plain angle cleats for securing purlins to wood trusses or rafters, knee piece inserts, two way and three way straps, plate washers and similar small articles complete all as specified and as directed. 77 s & fstainless steel curtain rod, 20 mm dia with fixing brackets, end caps etc complete all as specified and as directed. 78 s & f second class hard wood, plain, solid, straight chowkats and frames, wrought, framed, rebated on the solid, rounded or chamfered, put together with glue, pinned at joints complete all as specified and directed. 79 s & f factory made, 30 mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and as directed. 80 s & f factory made, 30mm thick, second class hard wood, glazed and skeleton door shutters, open rebated and prepared to receive glass, gauze, etc. [ without sash bars ] , edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc., sizes of members of shutters as specified in ssr part – i, section 8, clause 8.24 [ a ] and fitted to chowkats complete all as specified and as directed. 81 s & f aluminium alloy anodised sliding door bolt with hasp and staple [ bolt type ] of size 250 mm and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and as directed. 82 s & f aluminium anodised barrel tower bolt of size 300 mm size of extruded section complete all as specified and as directed. 83 s & f aluminium anodised handle, of extruded section fabricated type of size 200mm long complete all as specified and as directed. 84 m & l for two coats of synthetic enamel paint over one coat of red oxide / zinc chrome primer on new steel surfaces over 10cm width or girth including preparation of surfaces complete all as specified and as directed. 85 m & l for providing pre construction anti termite treatment for the backfill in contact with foundation by applying emulsion at the rate of 7.5 litres per square metre of vertical surface [ area of the substructure in contact with back fill ] complete all as specified and as directed. 86 m & l for providing pre construction anti termite treatment for the top surface of filled earth by applying emulsion at the rate of 5 litres per square metre ofsurface complete all as specified and as directed. 87 m & l for providing pre construction anti termite treatment for the soil under plinth protection by applying emulsion at the rate of 5 litres per square metre of surfacearea complete all as specified and as directed. 88 m & l for providing pre construction anti termite treatment for the soil along with external perimeter of building by applying emulsion at the rate of 2.25 litres per running metre of the perimeter wall complete all as specified and as directed. 89 m & l for 150 mm dia rcc pipes, class np3, laid and jointed with collars laid in trenches and jointedwith cement mortar complete all as specified and as directed. 90 m & l for concrete bed to drain pipes of size 150 mm bore packing under and haunching against the sides of pipes after they are laid and fitted in cement concrete, type c2, 1:3:6, using 40mm graded stone aggregate complete all as specified and as directed. 91 s & f rolled mild steel work conforming to fe 410 w, grade e 250, quality a as in framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc complete, drilled for fixing of steel sheeting or other covering, doors etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings [ exclusive of steel sheeting or other covering, running rails and guides ] and hanging, also fastening and fixing complete all as specified and as directed. 92 m & l for granite stone slabs of 18 to 20 mm thick of colour mexican red / ruby red / z black / pearl black as in skirting, dado, risers of steps, jambs, pillars, wall lining [ veneering to wall ] etc. with machine cut edges, table rubbed and prepolished to smooth mirror finish all to required sizes, granite stone slabs shall be of design / pattern as directed, including diagonals, inlays, borders, margins in two or more colours / shades, designs / patterns of stone slabs, set and bedded with grey cement [ slurry ] and jointed andpointed flush using polymer based cementitious tiling joint filler to match the shade of the granite slabs over backing coat of 10mm thick in cement mortar 1:3complete all as specified and as directed. note: single stone slab shall be used for entire height of skirting / dado / risers and joints shall match with the flooring. 93 s & fstainless steel kitchen sink with drainage board, made of stainless steel sheet of 1 mm thick, with plugs, washers, waste fittings, 32 mm dia, brass, chromium plated, and 32mm dia pvc flexible waste pipe, 750 mm long, including bedding in cement mortar to dwarf wall or including fixing cantilever ci brackets and connecting union to waste pipe, over all size 915 mm x 460 mm bowl size 410 mm x 330 mm x 160 mm complete all as specified and as directed. 94 s & f floor door stopper of size 150 mm of aluminium alloy body and tongue, anodised, with hard drawn steel spring complete all as specified and as directed. 95 m & l for point wiring complete with 1100 volts, frls grade, 1.5 sq.mm, single core, two runs, pvc insulated, unsheathed, multistranded copper conductor cable, conforming to is 694 drawn through and including heavy duty pvc conduit, 20 mm dia including all accessories concealed in walls / roofs / floors / ceiling etc. or surface type / semi concealed type and metal gi flush box of suitable size and thickness including modular type base / grid frame & cover frame for housing modular type switches, sockets and regulators etc. concealed in walls, including 1100 volts, frls grade, 1.5 sq.mm, single core, pvc insulated, unsheathed, multistranded copper conductor cable as earth continuity conductor with colour coding and connecting to earth dolly for one light / fan point / bell point / switchcomplete all as specified and as directed. 96 all as per serial item no. 91 above but one 3 pin switch socket outlet 5 amps on independent board complete all as specified. 97 all as per serial item no. 91 above but one 3 pin switch socket outlet 5 amps on same board complete all as specified. 98 all as per serial item no. 91 above but one 15 amps power point on independent board, with 1100 volts, frls grade, 4.0 sq.mm, single core, pvc insulated, unsheathed, multistranded copper conductor cable confirming to is 694 and including 1100 volts, frls grade, 4.0 sq.mm, single core, pvc insulated, unsheathed, multistranded copper conductor cable as earth continuity conductor. 99 s & f switch, modular type, one module, single pole, one way, 6 amps, 230 volts complete all as specified and as directed. 100 s & f switch modular type, one module, single pole, one way, 16 amps, 230 volts complete all as specified and as directed. 101 s & f ceiling rose, pvc body, 65 x 50 mm, three terminals, 230 volts complete all as specified and as directed. 102 s & f socket outlet, 3 pin, 6 amps, modular type, two modules, 230 volts, complete all as specified and as directed. 103 s & f socket outlet, 3 pin, 16 amps and 3 pin, 5 amps, modular type, two modules, multipurpose, 230 volts complete all as specified and as directed. 104 s & f bell push, modular type, single pole, 5 amps, 230 volts complete all as specified and as directed. 105 s & f bell, ding dong / multi music type, ac, 230 volts, single pole complete all as specified and as directed. 106 s & f sp & n enclosure with 2 pole and earth metal plug & socket for incorporating sp mcb complete including one mcb, sp, 20 amps, 240 volts complete all as specified and as directed. 107 s & f surface & wall mounted energy efficient led tube light fitting, of not less than 2000 lumens output, 5700 k of cool white, with extruded aluminium / crca housing and robust construction with necessary acrylic diffuser & integrated electronic driver, all accessories internally prewired and connecting up with twin core pvc insulated, sheathed flexible copper conductor cable of size 1.5 sq.mmcomplete all as specified and as directed. note: light fitting shall be of pf>0.95 108 s & fsurface & wall mounted energy efficient led decorative lamp, of not less than 1000 lumens output, 5700 k of cool white, with extruded aluminium / crca housing and robust construction with necessary acrylic diffuser & integrated electronic driver, all accessories internally prewired and connecting up with twin core pvc insulated, sheathed flexible copper conductor cable of size 1.5 sq.mm complete all as specified and as directed. note: light fitting shall be of pf>0.95 109 s & fenergy efficient sleek led mirror light fitting of not less than 500 lumens, surface & wallmounted with acrylic / pmma diffuser for soft glare free light with all accessories internally prewired and including connecting up with twin core pvc insulated, sheathed flexible copper conductor cable of size 1.5 sq.mm and complete all as specified and as directed. note: light fitting shall be of pf>0.95 110 s & f energy efficient, low noise, ceiling fan, 1200mm sweep of any colour as approved, 03 blades, bee 5 star rated, with bldc motor, copper wound, 350 rpm, with double ball bearing, conforming to is 374, isi marked, suitable for operation on single phase, 240 volts, ac, 50hz, including down rod, canopies, shackles, safety rope, hanging clamps, bushes, having p.f >0.95, service value >6.5, air delivery >215 cmm, power consumption less than 35 watt, thd less than 5%including provision of electronic speed control regulator step type, including connecting up with twin core pvc insulated, sheathed flexible copper conductor cable of size 1.5 sq.mm complete all as specified and as directed. note: ceiling fan shall be provided with 05 years onsite replacement warranty. rate quoted is deemed to be including the same and nothing shall be paid extra on this account. 111 s & f exhaust fan, 230mm sweep, 1400 rpm, metal body, heavy duty, with double ball bearing, generally conforming to is, isi marked, suitable for operation on single phase, 240 volts, ac, 50 hz, including louvers shutter / grill / guard, bee 5 star rated and of approved colour including connecting up with twin core pvc insulated, sheathed flexible copper conductor cable of size 1.5 sq.mm and fixing in existing opening and making good the disturbed surface to match with existing surfaces complete all as specified and as directed. 112 s & f energy efficient, bee 5 star rated storage type water heater [ geyser ] 25 litres capacity with 2000 watt capacity heating element conforming to is 2082, vertical storage type with specially designed titanium enamel coated / glass coated steel inner tank & heating element and abs outer shell complete fixed to wall with suitable expansion fasteners including 02 nos. of 450 mm long x 15mm dia stainless steel braided flexible hot & cold water connections and 15mm bore non return valvecomplete all as specified and as directed. note: geyser shall be provided with 05 years onsite replacement warranty. rate quote is deemed to be including the same and nothing shall be paid extra on this account. 113 s & f energy efficient & long life building security light luminaire, of not less than 4500 lumens output, 5700 k with pressure die cast aluminium housing, ip66 protection, heat resistant glass cover, high power leds as light source, electronic driver including gi bracket made out of 32 mm bore gi tube, medium grade of size not exceeding 1.50 m in length and bent to shape required and fixed with 2 nos of pole fitting clamps made out of ms flat of size 50 x 6mm, bolts, nuts, washers and painting with two coats of aluminium paint over a coat of primer red oxide zinc chrome primer and connecting up with three core pvc insulated, sheathed flexible copper conductor cable of size 1.5 sq.mmcomplete all as specified and as directed. note: light fitting shall be of pf>0.95 114 s & fmccb db v tpn, 4 way, 415 volts, with din channel, double door with 200 amps rated bus bar suitable for mounting mcbbs flush mounted with wall including making good disturbed surfaces complete all as specified and as directed. 115 s & fmcb db, spn, 12 way, 240 volts, with din channel, double door with 200 amps rated bus bar suitable for mounting mcbs flush mounted with wall including making good disturbed surfaces complete all as specified and as directed. 116 s & f mcb, spn, 40 to 63 amps, 10 ka, c curve, ac, 230 volts, 50 hz complete all as specified and as directed. 117 s & f mcb, tpn, 40 to 63 amps, 10 ka, c curve, ac, 230 volts, 50 hz complete all as specified and as directed. 118 s & f mccb, fp, 63 amps, 16 ka, 415 volts, 50 hz, suitable for fixing on n3 frame complete all as specified and as directed. 119 s & f mccb, fp, 125 amps, 16 ka, 415 volts, 50 hz, suitable for fixing on n3 frame complete all as specified and as directed. 120 s & fmcb, sp, 6 to 32 amps, 10 ka, c curve, ac, 230 volts, 50 hz complete all as specified and as directed. 121 m & l for sub main wiring with 2 runs of single core 2.5 sq.mm single core, pvc insulated, unsheathed, multistranded copper conductor cable, 1100 volts, frlsh grade, isi marked, drawing through and including heavy duty pvc conduit, 20 mm dia with all accessories concealed in walls / roofs / floors / ceiling etc. or surface type / semi concealed type including one run of 2.5 sq.mm, single core, pvc insulated, unsheathed, multistranded copper conductor cable, 1100 volts, frlsh grade earth continuity conductorcomplete all as specified and as directed. note: 3 runs of 2.5 sq.mm pvc insulated coper conductor cable& one run of 20 mm dia pvc conduit will be measured as one unit 122 m & l for sub main wiring with 2 runs of single core 4 sq.mm single core, pvc insulated, unsheathed, multistranded copper conductor cable, 1100 volts, frlsh grade, isi marked, drawing through and including heavy duty pvc conduit, 20 mm dia with all accessories concealed in walls / roofs / floors / ceiling etc. or surface type / semi concealed type including one run of 4 sq.mm, single core, pvc insulated, unsheathed, multistranded copper conductor cable, 1100 volts, frlsh grade earth continuity conductor complete all as specified and as directed. note: 3 runs of 4 sq.mm pvc insulated coper conductor cable& one run of 20 mm dia pvc conduit will be measured as one unit 123 m & l for sub main wiring with 2 runs of single core 6 sq.mm single core, pvc insulated, unsheathed, multistranded copper conductor cable, 1100 volts, frlsh grade, isi marked, drawing through and including heavy duty pvc conduit, 20 mm dia with all accessories concealed in walls / roofs / floors / ceiling etc. or surface type / semi concealed type including one run of 6 sq.mm, single core, pvc insulated, unsheathed, multistranded copper conductor cable, 1100 volts, frlsh grade earth continuity conductor including taking down old sub main wiring of any description and making good disturbed surface complete all as specified and as directed. note: 3 runs of 6 sq.mm pvc insulated coper conductor cable& one run of 20 mm dia pvc conduit will be measured as one unit 124 supplying, laying and testing xlpe insulated and pvc sheathed, frls, armoured heavy duty underground cable, isi marked with aluminium stranded conductor 1100 volt grade of size 3.5 core, 25 sq.mm cross section suitable for earthed system, laying in trenches / duct / fixed to poles / drawn through pipes / sleeving through pipe in duct, including suitable size double compression copper stainless steel cable gland, crimping type cable lugs, sockets etc. complete all as specified and as directed. 125 m & l for dry river sand cushioning over and around the cable for cable protection in trenches, levelled and punned down complete all as specified and as directed. note: the punned down thickness shall be measured for payment. 126 supply and lay bricks, common burnt clay building bricks, sub–class b, designation 75 in trenches for cable protection complete all as specified and as directed. 127 supplying and laying gi pipe, 40mm dia, light grade for cable protection at road crossing etc. or fixing on wall / poles of any type, secured with clamps complete all as specified and as directed. 128 m & l for cutting bituminous road / hardstanding etc. as required for jointing / laying cables and pipeline of width not exceeding 300mm and depth not exceeding 600mm and refilling after laying and making good with pcc 1:2:4, type b1 using 20mm graded stone aggregate, 100mm thick complete all as specified and as directed. 129 earthing complete with galvanised steel earth plate electrode 600 x 600 x 6 mm thick burried directly in ground [ earth pit not less than 2.25 m deep below ground level ] with top edge of plate not less than 1.50 m below normal ground level connected to 4 mm gi wire [ earth lead ] and gi pipe 15 mm, medium grade for earthing lead protection to the extent of maximum 7.5m, earth plate electrode surrounded by 150mm thick packed layers of charcoal and common salt filled in alternate layers, connected to the plate by means of gi bolts & nuts complete all as per electrical plate no. 3 of ssr part – i, connected to panel / db including testing on completion including main earthing, charcoal, common salt, pcc [ 1:2:4, type b1 ] pit with rcc 1:2:4, type b1 cover, 50 mm thick with 6 nos, 8 mm dia tmt bars in both ways, ms frame made with 40 x 40 x 6 mm angle iron, ms funnel with 20 mm bore, medium grade gi watering pipe, wire mesh, earth work excavation, return filling, removal of surplus soil etc.complete all as specified and as directed. 130 s & f microprocessor based single phase, 2 wire smart prepaid electronic tamper proof digital energy meter with bright lcd display, in home display unit including implementation of vending software system through server duly mapping of consumer, token system, load control facility, optical port for local communication / consumer interface unit with in built blue tooth low energy [ ble ] for remote access and alongwith vending software, high accuracy, rating 5 to 60 ampswith class 1 accuracy, ip 54 ingress protection, conforming to is 16444 & is 15959, iec 62055 31, iec 62053 21, iec 62052 11, cbip publication no. 304, isi marked, suitable for 240 volts, ac, 50 hz, including housing inmeter box with provision for earth connection, two separate cable entries for incoming and outgoing cables, transparent glass door for reading visibility with hinges and provision of 4 nos. of tamper proof lead free seals, complete all as specified and as directed. make: siemens / l & t / havells / hpl / schneider / securenote: [ a ] energy meter shall be provided with 10 years onsite replacement warranty and the rate quoted is deemed to be including the same and nothing shall be paid extra on this account. [ b ] the bidder is required to submit authenticity certificate issued by oem for the meters supplied under this contract. [ c ] meter box shall be measured for and paid separately under relevant item of boq. 131 s & f hot press moulded smc meter box of size not less than 250mm ( h ) x 250mm ( w ) x 155mm ( d ) suitable for housing of single phase prepaid electric energy meter, conforming to relevant is, with viewing glass, hinged door and earth bolt, mounted on pole / wall with suitable clamps / bolts / nuts complete all as specified and as directed.make: cat no. gsmb 2525 of sintex or equivalent in hensel / c&s 132 s & f upvc pipe of 50 mm bore, of pressure rating 10 kgf / sq.cm including all fittings such as bends, tees, short pieces, connectors, elbows, reducers, sockets etc and fixed to walls, ceiling, and laid on floors including testing complete all as specified and as directed. 133 s & f upvc pipe of 25 mm bore, of pressure rating 10 kgf / sq.cm including all fittings such as bends, tees, short pieces, connectors, elbows, reducers, sockets etc and fixed to walls, ceiling, and laid on floors including testing complete all as specified and as directed. 134 s & f gun metal globe or gate valve of class i, pressure tested of 1.5 mpa, 50 mm bore with iron wheel head, screwed both ends for iron pipe, conforming to is, isi marked complete all specified and as directed. 135 m & l for cutting or screwing existing steel tubing for alteration or additions of suitable size for 50mm dia complete all specified and as directed. 136 m & l for construction of valve chamber of size 600 x 600 x 600 mm internal size suitable for sluice valve, with pcc 1:4:8, type d2, using 40mm graded aggregate for foundation, 200 mm thick brickwork with fly ash bricks in cement mortar 1:6, 40 mm thick pcc, 1:2:4, type b1, using 20mm graded aggregate coping, rendering in cm 1:4, 15 mm thick including provision of mild steel sheet cover 3 mm thick with 40 x 40 x 6 mm size angle iron frame work embedded in concrete with suitable hinges and locking arrangements including two coat of synthetic enamel black paint over a coat of red oxide zinc chrome primer to steel surfaces and includingdemolition of existing valve chamber, necessary earth work excavation in any type of soil etc., removal of surplus soil off the premises complete all as specified and shown on drawing cedd / td / 119, sheet no. 1 / 1 dated 20 august 1983, revised up to 21 september 1992....

Society For Applied Microwave Electronics Engineering And Research - Andhra Pradesh

33470531 supply of material for swachh bharat program 1. plant saplings 2. poster / brochure 3. cement pots ( 2*2 ft ) 4. white cement bag & paints ) white cement bags 25 kgs b ) outdoor enamel paints i lts c ) strainers 100 ml d ) exterior emulsion paint 4 its 5. lute bags / paper bags 6. memento 7. decorative solar lights 8. palm ieaf bags for plants=> limited...

Vijayawada Municipal Corporation - Andhra Pradesh

33343358 providing multiply equipment in children play area in rajiv gandhi park in circle i area. 0.00 supply, delivery and commissioning of the following children play equipment of standard brands customized / standard option as preferred by the department including cost and conveyance of materials to site area proposed for installation and commission as per the model image furnished herewith and as directed by the departmental authorities. 0 0 0 0 0 1.00 double sea saw with 4 seated ; 8 feet length and 4 feet width 1 – 6” height mounted on central frame structure of 80nb ‘c’ class gi pipes of tata / jindal make and with proper hinges, holders. bolts and nuts, powder coated multi color painting to 60 to 70 microns and seat of high quality lldpe materials – all materials confirming to is codes. double sea saw with 4 seated0 double sea saw with 4 seated quotation 38000 each 1.00 double arch swing double arch swing of 6.50m x 1.50m size four seated with 6m long 80nb gi pipe bent in single piece and welded together with a flange 5mm their of is 40x40x5mm to form a strong frame bottom and middle height of the frame in 2700mm; top pipe 50nb gi pipe 2950mm length; swing clamp assembly made up of two parts are joined together with m6 allen bolts along with ‘s’ hook to house a bearing for smooth and noiselen swing; rubber dip molded 6 mm dia 1450mm along swing chain; ‘s’ hook of 8mm dia 145 x 130mm triangular hook of ss 304 grade; seats made of lldpe; self lubricated skf / ntn / nachi make bearings; pins and clips of 12mm dia – all framing pipes of ‘c’ class gi pipe of tata / jindal make and powder coated multicolor optional painting of 50 70 micros and all materials shall confirming to is codes. double arch swing double arch swing quotation 88000.00 each 1.00 6 seater merry go round made of gi frame of ‘c’ class tata / jindal make vertical pipe of 80nb; and framing pipes of 32mm nb & 50mm with ldpe seating base 6 feet dia and powder coated multicolor optional painting of 50 70 microns and all materials shall confirming to is codes. 6 seater merry go round 6 seater merry go round quotation 68000.00 each 1.00 multi play system – designed: main post: 114mm od galvanized post, height 10ft, post end closed with aluminum cap. platform size: 3.5ft x 3.5ft laser cut 2mm thickness mild steel sheet with drain holes bended as per standards. double swing: 7.5 ft height, length 9ft. polyethylene seats – 2nos, pu coated chains. steps size: 2ft width with 2mm thickness mild steel sheet with drain holes bended as per standards. roof: polyethylene roof made of two different styles. wheel climber / arch climber / grill: polyethylene. wave slide 2nos, length 8ft. metal parts completely powder coated. seesaw pipe: 114mm od, all metal post are galvanized, electrostatic powder coated. back rest seat: polyethylene, aluminum cap on top, sealed bearings for smooth movement. product dimension: l 7ft x w 2ft x h 2.5ft multi play system multi play system quotation 1, 064, 300.00 each 10.00 earthwork excavation for foundations and depositing on bank for all lifts and with an initial lead of 10m including all operational incidentalm labour charges such as shoring, sheeting, planking, struting, etc, complete for finished item of work including seigniorage exclduing dewatering charges etc, as per ss 20 b ( apss 308 ) earthwork excavation earthwork excavation sor 2021 22 273.99 1cum 18.50 collection and supply of dust for filling including cost and conveyance, spreading, sectioning etc., complete. supply of dust for filling supply of dust for filling sor 2021 22 1, 025.82 1cum 160.00 25 mm thick sbr with epdm insitu rubber flooring for outdoors *100% hygienic and safer for children *an unmatched range of creative design possibilities & long life with minimal wastage possibilities & long life with minimal wastage *resistance to abrasion, slipping, indentation & ignition & virtually maintenance free *multi colored graphic and design options *no hidden hazards *no joints for vandals to crack *ebaco epdm flooring surface depths varies in thickness. 15 to 36 mm thickness is the „industry standard‟ incorporating a 2 layer system with a 9 / 19 / 30mm sbr base layer and 6mm epdm wearing top. *all depths can be accommodated. “if one keeps thickness of floor 25 mm, it means, if a child falls from height of approx 1 meter it won‟t hurt himself.” 25 mm thick sbr 25 mm thick sbr sor 2021 22 365.00 1sqm 2.50 providing concrete for plain concrete ( m10 ) using 220 kgs cement , 40 mm nominal size hard stone aggregate , mechanically mixed, placed in foundation and compacted by vibration including curing for 14 days complete as per drawings and technical specifications of morth plain concrete ( m10 ) plain concrete ( m10 ) sor 2021 22 4, 113.04 1cum 20.25 providing concrete for plain concrete ( m20 design mix ) using 343 kgs cement , 20 mm, 10mm nominal size graded hard stone aggregate , mechanically mixed, placed in foundation and compacted by vibration including curing for 14 days complete as per drawings and technical specifications of morth with out form work plain concrete ( m20 design mix ) plain concrete ( m20 design mix ) sor 2021 22 5, 221.25 1cum 6.00 brick masonry work ( 1:5 ) in cement mortar in foundation complete excluding pointing and plastering as per drawing and technical specifications clauses 600, 1202 & 1203 mord / 1300 morth with second class bricks & moulded bricks brick masonry work ( 1:5 ) i brick masonry work ( 1:5 ) i sor 2021 22 6, 591.58 1cum 65.00 plastering with cm ( 1:4 ) , 12mm thick including cost and conveyance of all material, labour charges for mixing watering etc complete plastering with cm ( 1:4 ) , 12mm thick plastering with cm ( 1:4 ) , 12mm thick sor 2021 22 1, 236.38 10sqm 65.00 supply & application of one coat water based cement primer of exterior grade ii and two coats of acrylic exterior emulsion paint having voc ( volatile organic compound ) content less than 50 grams / litre for exterior walls including cost and conveyance of all materials to site, and all operational, incidental, labour charges etc., and overheads & contractors profit complete for finished item of work in all floors. one coat water based cement primer one coat water based cement primer sor 2021 22 272.70 10sqm total...

Tirumala Tirupati Devasthanams - Andhra Pradesh

33172632 comprehensive maintenance of roads, foot paths and parking places ( including benches garden railings ) at various places in tirumala. , comprehensive and maintenance of roads, footpaths and parking places including responsible for providing timely maintenance of all types of tirumala roads, footpaths, parking areas, ( pavers area ) , road edge kerb walls, foot path end retention walls with grills, garden grills along the road edges etc., of following areas in various places in tirumala ( as per item no.1 of boq attached in the tender document ) , providing and laying bituminous concrete of specified thickness by hot mix plant 100 120 tph capacity using bitumen of grade vg30, irc size hbg crushed stone aggregates of specified grading ( table 500 17 ) premixed with bituminous binder and filler ( cement opc 43 / 53 grade ) transporting the hot mix to work site, laying with a mechanical paver finisher to the required grade, level and alignment rolling with smooth wheeled 8 10 tonne, vibratory 8 10 tonne and tandem 6 8 tonne rollers to achieve the desired compaction as per specification vide clause no.507 of morth ( 5th revision ) etc., complete in all respects and as directed by the engineer in charge during execution. grading ii 13.2mm ( nominal size ) layer thickness 30 to 40mm with bitumen binder at 5.4 percent mimimum, road marking with hot applied thermoplastic compound with reflectorising glass beads on bituminous surface. providing and laying of hot applied thermoplastic compound 2.5 mm thick including with reflectorising glass beads at 250 gms per sq.m area, thickness of 2 mm is exclusive of surface applied glass beads as per irc:35.the finished surface to be level, uniform and free from steaks and holes as per specification 803 morth., painting with ready mixed synthetic enamel paint in all shades grade i having voc ( volatile organic compound ) content less than 50 grams / liter approved colour and make including brushes to have an even shade including cost and conveyance of all materials as directed during execution complying with standard specifications etc., complete. do single coat for old iron work / old plastered surface, painting with acrylic emulsion paint exterior grade with silicon additives having voc ( volatile organic compound ) content less than 50 grams / liter of approved brand and shade after thoroughly brushing the surface to remove all dirt and remains of loose powdered materials, including cost and conveyance of all materials to work site and all operational, incidental, labour charges etc., complete for finished item of work as per ss 911 for external walls. do single coat for external walls for old work, supplying and fixing in position m.s ornamental grills for windows and ventilators or for veranda openings using m.s. flats, square rods, angles sheets etc., of approved design including necessary cuttings, bending fabrication, welding, grinding and finishing smooth including painting the grills with two coats with synthetic enamel paint over a primary coat ( red oxide metal primer ) ( total three coats ) of approved make and colour including cost of making the holes into rcc or masonry works and making good the same wherever necessary, including cost and conveyance of all materials, incidental charges etc., complete., providing and fixing precast concrete blocks ( interlocking pavers ) using not less than m 40 grade paver blocks and thickness not less than 80 mm for medium traffic areas conforming to is 15658 2006 of all shapes and designs as per the specification, over sand bed of 20 mm to 40 mm ( 30 mm average ) thickness and compacting with vibrating plate compactor having 3 tonne compaction force there by forcing part of sand underneath to come up in between joints. final compaction of paver surface to be done after spreading and brushing the fine sand into joints to its final level. the work includes cost of all materials such as interlocking pavers, sand etc., labour and equipments such as cutting machine, lift, loading and unloading to work site clearing, bringing required all materials for the successful completion of work as per drawings and technical specification clause 1504 mord and as directed during execution by the engineer in charge of the work., flooring with cement concrete floor tiles of 25 mm thick of chequerred cement concrete heavy duty tiles confirming to is:13801 using aggregates, cement, pigments of size 300 x 300 mm of any shades set over base coat of cement mortar ( 1:6 ) 20 mm thick over cc bed already laid or rcc roof slab, including neat cement slurry of honey like consistency spread at 3.3 kgs per sqm and jointed with neat cement to full depth mixed with pigment of matching shade including cost and conveyance of all materials, etc., complete for finished item of work....

Tirumala Tirupati Devasthanams - Andhra Pradesh

32789551 comprehensive maintenance of roads, foot paths and parking places (including benches garden railings) at various places in tirumala. , comprehensive and maintenance of roads, footpaths and parking places including responsible for providing timely maintenance of all types of tirumala roads, footpaths, parking areas, (pavers area), road edge kerb walls, foot path end retention walls with grills, garden grills along the road edges etc., of following areas in various places in tirumala as mentioned in the item no 1 of boq attached,providing and laying bituminous concrete of specified thickness by hot mix plant 100 120 tph capacity using bitumen of grade vg30, irc size hbg crushed stone aggregates of specified grading (table 500 17) premixed with bituminous binder and filler(cement opc 43/53 grade) transporting the hot mix to work site, laying with a mechanical paver finisher to the required grade, level and alignment rolling with smooth wheeled 8 10 tonne, vibratory 8 10 tonne and tandem 6 8 tonne rollers to achieve the desired compaction as per specification vide clause no.507 of morth (5th revision) etc., complete in all respects and as directed by the engineer in charge during execution. do grading ii 13.2mm (nominal size) layer thickness 30 to 40mm with bitumen binder at 5.4 percent minimum,road marking with hot applied thermoplastic compound with reflectorising glass beads on bituminous surface.providing and laying of hot applied thermoplastic compound 2.5 mm thick including with reflectorising glass beads at 250gms per sq.m area, thickness of 2 mm is exclusive of surface applied glass beads as per irc:35.the finished surface to be level,uniform and free from steaks and holes as per specification 803 morth.,painting with ready mixed synthetic enamel paint in all shades grade i having voc (volatile organic compound) content less than 50 grams/liter approved colour and make including brushes to have an even shade including cost and conveyance of all materials as directed during execution complying with standard specifications etc., complete. do single coat for old iron work / old plastered surface,painting with acrylic emulsion paint exterior grade with silicon additives having voc (volatile organic compound) content less than 50 grams/liter of approved brand and shade after thoroughly brushing the surface to remove all dirt and remains of loose powdered materials, including cost and conveyance of all materials to work site and all operational, incidental, labour charges etc., complete for finished item of work as per ss 911 for external walls. do single coat for external walls for old work,supplying and fixing in position m.s ornamental grills for windows and ventilators or for veranda openings using m.s. flats, square rods, angles sheets etc., of approved design including necessary cuttings, bending fabrication, welding, grinding and finishing smooth including painting the grills with two coats with synthetic enamel paint over a primary coat (red oxide metal primer) (total three coats) of approved make and colour including cost of making the holes into rcc or masonry works and making good the same wherever necessary, including cost and conveyance of all materials, incidental charges etc., complete.,providing and fixing precast concrete blocks (interlocking pavers) using not lessthan m40 grade paver blocks and thickness not less than 80 mm for medium traffic areas conforming to is 15658 2006 of all shapes and designs as per the specification, over sand bed of 20 mm to 40 mm (30 mm average) thickness and compacting with vibrating plate compactor having 3 tonne compaction force there by forcing part of sand underneath to come up in between joints. final compaction of paver surface to be done after spreading and brushing the fine sand into joints to its final level. the work includes cost of all materials such as interlocking pavers, sand etc., labour and equipments such as cutting machine, lift, loading and unloading to work site clearing, bringing required all materials for the successful completion of work as per drawings and technical specification clause 1504 mord and as directed during execution by the engineer in charge of the work.,flooring with cement concrete floor tiles of 25 mm thick of chequerred cement concrete heavy duty tiles confirming to is:13801 using aggregates, cement, pigments of size 300 x 300 mm of any shades set over base coat of cement mortar (1:6) 20mm thick over cc bed already laid or rcc roof slab, including neat cement slurry of honey like consistency spread at 3.3 kgs per sqm and jointed with neat cement to full depth mixed with pigment of matching shade including cost and conveyance of all materials, etc., complete for finished item of work....

Municipalities - Andhra Pradesh

32789377 providing emulsion paint to internal walls to administration room, asst. commissioner chamber, pura seva, sharoof room, birth death room in ground floor in magnalagiri main office in mangalagiri tadepalli municipal corporation under general funds...

Municipalities - Andhra Pradesh

32789375 providing emulsion paint to internal walls to old record room, cc room and new record room in first floor in magnalagiri main office in mangalagiri tadepalli municipal corporation under general funds...

Municipalities - Andhra Pradesh

32635779 providing painting , supply and fixing of electrical items to dr.ysr urban clinic ( urban primary health center ) at nsp guest house area in sattenapalle municipality in guntur district 2nd call 825.00 providing and applying synthetic plaster putty or plaster of paris putty or lime punning of average 1 to 2 mm thickness over plastered surface to prepare the surface even and smooth after thoroughly brushing the surface to remove all dirt and remains of loose powdered materials, applying emery paper, sand the surface, clean & wipe off loose dust, applying knifing paste filler by putty knife / muslin pad, air dry for 2 3 hrs, sand with 180 and 320 no., emery paper for the surface preparation including cost and conveyance of all materials to work site and all operational, incidental, labour charges etc. complete for finished item of work for internal walls 870.00 providing and applying synthetic plaster putty or plaster of paris putty or lime punning of average 1 to 2 mm thickness over plastered surface to prepare the surface even and smooth after thoroughly brushing the surface to remove all dirt and remains of loose powdered materials, applying emery paper, sand the surface, clean & wipe off loose dust, applying knifing paste filler by putty knife / muslin pad, air dry for 2 3 hrs, sand with 180 and 320 no., emery paper for the surface preparation including cost and conveyance of all materials to work site and all operational, incidental, labour charges etc. complete for finished item of work for external walls 825.00 painting to new walls with 2 coats of plastic emulsion paint of approved brand and shade after thouroughly brushing the surface to remove all dirt and remains of loose powdered materials, inlcuding cost and conveyance of all materials to work site and all operational, incidental, labour charges etc., complete for finished item of work as per ss 911 for internal walls. 870.00 painting to new walls with 2 coats of plastic emulsion paint of approved brand and shade after thouroughly brushing the surface to remove all dirt and remains of loose powdered materials, inlcuding cost and conveyance of all materials to work site and all operational, incidental, labour charges etc., complete for finished item of work as per ss 911 for external walls. 100.00 supply and fixing of 25mm dia 1.80mm thick pvc pipe ( isi mark ) concealed in slab with all required accessories including masonary work and labour charges etc., complete.. 125.00 supply and fixing of 20mm dia 1.55mm thick surface pvc pipe ( isi mark ) in wall with all required accessories including masonary work and labour charges etc., complete. 25.00 supply and fixing of 20 24w, not less than 1100mm length led batten light with extruded alluminium housing and polycarbonate cover, input voltage ac 220 260 volts with pf>0.9, surge protection: 2kv, thd<15%, with inbuilt driver and frosted cover cct: 3000k 5700k, minimum cri>70, .etc., complete. makes : as per list of recommended brands as category i. 8.00 supply of 7 w lamp with input voltage 90 to 300v, colour temparature 3000k 6500k, beam angle 170 220 degrees, b22 base, .makes: phillips / crompton / bajaj / havells / halonix / gm / hplsyska / green lites / fortune art / goldmedal / luker / leo / orbit / rhino / glo led 14.00 supply and fixing 1200 mm ( 48 ) / sweep 230v, a.c 50 hz.ceiling fan with 3 blades and double ball bearings with all standard accessories. 14.00 supply and erecting supply of stepped type electronic regulator. makes: gm g home / gold medal olive / million zoom / for ceiling fans complete erected on existing board. 100.00 wiring with 2 runs of 14 / 0.3mm ( 1.0 sq.mm ) fire retardant ( fr ) p.v.c. insulated flexible copper cable ( isi mark ) in existing pipe with 6a switch, ceiling rose and 3mm thick hylam sheet covering to switch control box including all labour charges etc., complete. 20.00 supply and fixing of 6a 3 pin wall plug socket with 6a switch control on a common switch board with earth continuity including wire leads, earth connections along with all labour charges etc., complete 400.00 supply and run of 2 of 36 / 0.3mm ( 2.5 sq.mm ) f.r p.v.c. insulated flexible copper cable in existing pipe for mains inlcuding all labour charges etc., complete. 50.00 supply of 25mm dia pvc junction boxes confirms to is : 3419 make :precision / universal& marudhar / vip / goldmedal / million plast / gm / sudhakar / polyline / orbit / anchor / akg / polycab ( elec 1.2.6 ) 10.00 supply and fixing of 16a 3pin and 6a 3pin plug socket with indicator lamp and 16a fuse unit and 16a switch control ( 5 in 1 ) duly recessed in wall with wooden deep box of 6 x8 x2 1 / 2 size covered with hylam sheet including earth connections and all lab 15.00 supply of 6 32a sp mcb 10ka c / d curve isi mark.makes: legrand dx3 / schneider acti9 / hager h3 / siemens 5sx4 / crabtree xpro / l&t au / indo asian opti pro 2.00 supply of 12 way spn db with ip 43.protection suitable for 12 nos s.p out goings and for 1 no incommer etc complete as per is 8623; is 13032; iec 61439 3. makes: legrand ( ekinox 3 ) / schneider acti9 / hager novello+ / seimens / crabtree xpro classique ii / l&t newrange / indo asian opti pro. ( elec 2.13.1 ( f ) ) 1.00 supply of 63a fp isolator. makes: legrand dx3 / schneider acti9 / hager h3 / siemens 5sx4 / crabtree xpro / l&t au / indo asian opti pro ( elec 2.11.1 ) 6.00 supply of 12 hot dip galvanized 20 / 18 swg module box with earthing terminal ( elec 1.3.1 ) 6.00 supply of 8 hot dip galvanized 20 / 18 swg module box with earthing terminal ( elec 1.3.1 ) 6.00 supply of 6 hot dip galvanized 20 / 18 swg module box with earthing terminal ( elec 1.3.1 ) 30.00 supply of 20 mm . pvc bends.make : precision / universal& marudhar / vip / goldmedal / million plast / gm / sudhakar / polyline / polycab / akg / orbit / beljin 25.00 supply of 6a / 10a 2 way 1 module modular switch. makes: legrand arteor / schneider zen celo / crabtree murano or amare / l&tenglaze / gm zenova / goldmedal ( gifa ) 20.00 supply of 12 modular vertical cover frame makes: legrand arteor / schneider zen celo / crabtree murano or amare / l&tenglaze / gm zenova / goldmedal ( gifa ) ( elec 1.8.3 f ) 2.00 supply of 4 way tpn db horizontal with ip 30 protection as per is:13032 and suitable for 12 nos s.p. out goings and for 1 no 4 pole incommer etc complete. makes: legrand ( ekinox 3 ) / schneider 150.00 supply of 6 sqmm wptc ( weather proof twin core ) isi alluminium wire. makes: gold medal / million / gm / vimal / finecab / nakoda / nanadicab / payal / kundan cab / sudhakar 8.00 supply and transportation of 30w led street light luminaire made of pressure diecast alluminium body with powder coated, having protective toughned glass, supply input voltage 120 270 v ac, p.f > 0.90, high power leds having system efficacy >95lm / w and junction temprature < 70°c, with ingrees protection ip65, luminaire performance complies to is 10322 ( part 5 / sec 3 ) , driver surge protection 4kv, external surge protection ≥ 5kv with optics distribution type ii medium, thd<10% at 110 volts ac, driver efficiency >90%, w, cct: 3000k 5700k, minimum cri>70, etc., complete a ) luminaire makes : trinic / pasolite / semtronics / vriliso / prolite / sieger / oreva b ) led make : cree / nichia / osram / samsung / lg. 400.00 supply of 10 sqmm wpsc ( weather proof single core ) isi alluminium wire. makes: gold medal / million / gm / vimal / finecab / nakoda / nanadicab / payal / kundan cab / sudhakar 390.00 providing art painting with extrerior emulsion paint two coats over two coats of primary coat of exterior emulsion paint & painting of clip art / 3d bubble art with enamel paint over old plastered walls of under bridges / over bridges / low bridges, including cost and conveyance of all materials and labour charges etc., complete painting with acrylic exterior emulsion paint having voc content less than 50gm / ltr as per is specification and standard as approved by thr agreement authority to be used for primary coat & 2 coats above that rate as per cdma roc.no 1481 / 2015 / m3, dt:03.04.2018...

Municipalities - Andhra Pradesh

32340624 providing non figurative painting with exterior emulsion paint to both side dividers from church center to msr statue via collector camp office road in ongole municipal corporation...

Hindustan Shipyard Limited - Andhra Pradesh

31940577 procurement of colony paints procurement of colony paints , light blue colour premium quality exterior weather proof emulsion paint of approved make asian (apex ultima) / berger (all guard) , dark blue colour premium quality exterior weather proof emulsion paint of approved make asian (apex ultima) / berger (all guard) , light cream colour premium quality exterior weather proof emulsion paint of approved make asian (apex ultima) / berger (all guard) , dark cream / brown colour premium quality exterior weather proof emulsion paint of approved make asian (apex ultima) / berger (all guard) , white synthetic enamel paint , green colour synthetic enamel paint...

Vijayawada Municipal Corporation - Andhra Pradesh

31178451 supply and fixing of open gym equipments in andhra ratna park, 33rd division in works division ii area. sky walker double*dimensions sky walker double*dimensions air walker double*dimensions air walker double*dimensions seated puller double **dimensions seated puller double **dimensions chest press double*dimensions chest press double*dimensions triple standing twister*dimensions triple standing twister*dimensions thaichi spinner 4 wheel *dimensions thaichi spinner 4 wheel *dimensions earth work excavation for foundations (manual means) earth work excavation for foundations (manual means) collection and supply of stone dust for filling collection and supply of stone dust for filling providing concrete for plain concrete (m10) providing concrete for plain concrete (m10) brick masonry in cm (1:6) with bricks brick masonry in cm (1:6) with bricks plastering for walls in cm (1:4) 12mm thick plastering for walls in cm (1:4) 12mm thick painting with plastic emulsion paint grade i painting with plastic emulsion paint grade i providing concrete for plain concrete (m15 design mix) providing concrete for plain concrete (m15 design mix) supply of precast concrete blocks for paving of m 35 grade supply of precast concrete blocks for paving of m 35 grade ...

Vijayawada Municipal Corporation - Andhra Pradesh

31016156 supply and fixing of open gym equipments in andhra ratna park, 33rd division in works division ii area. sky walker double , air walker seated puller chest press double triple standing twister , thaichi spinner 9.84 earth work excavation for foundations (manual means) of buildings, septic tank, sump, compound wall in ordinary soils and depositing on bank with an initial lead of 10m and depth up to 3m including all operational,incidental, labour charges such as shoring, sheeting, planking, strutting etc., and overheads & contractors profit complete for finished item of work excluding dewatering charges etc., as per ss 20 b(apss 308) earth work excavation for foundations (manual means) earth work excavation for foundations (manual means) 29.84 collection and supply of stone dust for filling including cost and conveyanceof all materials and labour charges for spreading, sectioning, levelling and watering etc., complete collection and supply of stone dust for filling collection and supply of stone dust for filling 1.84 providing concrete for plain concrete (m10) using 220 kgs cement ,40 mm nominal size hard stone aggregate , mechanically mixed, placed in foundation and compacted by vibration including curing for 14 days complete as per drawings and technical specifications of morth providing concrete for plain concrete (m10) providing concrete for plain concrete (m10) 7.00 brick masonry in cm (1:6) with bricks traditional size 23x11x7 cms 2nd class including cost and conveyance of all materials and labour charges for mixing of mortor watering curing etc. complete. brick masonry in cm (1:6) with bricks brick masonry in cm (1:6) with bricks 60.00 plastering for walls in cm (1:4) 12mm thick including cost and conveyance of all materials, labour charges for mixing of mortor watering curing etc. complete. plastering for walls in cm (1:4) 12mm thick plastering for walls in cm (1:4) 12mm thick 60.00 painting with plastic emulsion paint grade i to given an even shade after throughly brushing the surface to remove all dirt and remains of losse powdered materials, including cost and conveyance of all materials to work site and all operational incidental labour charges etc., complete for finished item of work as per ss painting with plastic emulsion paint grade i painting with plastic emulsion paint grade i 2.12 providing concrete for plain concrete (m15 design mix) using 275 kgs cement ,20 mm,10mm nominal size graded hard stone aggregate , mechanically mixed, placed in foundation and compacted by vibration including curing for 14 days complete as per drawings and technical specifications of morth providing concrete for plain concrete (m15 design mix) providing concrete for plain concrete (m15 design mix) 135.00 supply of precast concrete blocks for paving of m 35 grade and thickness not less than 60 mm for light traffic areas conforming to is 15658:2006 in all shapes and designs as per the manufacturers specification set over not less than 30 mm thick sand bed, spreading sand over joints to full depth including cost and conveyance of all materials and labor charges for paving true to alignment and design pattern as directed by the department authorities supply of precast concrete blocks for paving of m 35 grade supply of precast concrete blocks for paving of m 35 grade ...

Andhra Pradesh State Police Housing Corporation Limited - Andhra Pradesh

30627007 repairs to electrical sanitary items and repairs to bath rooms in ctc at visakhapatnam city 2.00 masonry work in cm ( 1:4 ) prop with flyash cement solid blocks of size 290 x 100 x 140 mm with a compresive strength not less than 50 kg / sqm including cost and conveyance of all materials, labour charges, seiniorage charges, scaffolding and curing etc., cpomplete for finished item of work. partition and parapet walls 100 mm thick ground floor ( apss no. 501&504 ) . 100.00 providing dadooing to internal walls with digital / polished glazed full body porcelain wall tiles of size 300 x 600 mm with any type of design texture such as marble finish, wooden, bamboo, stone finishes etc., scratch less, stain free and thickness between 6 8 mm 1st quality conforming to is:13711, is:13712, is:13630 ( parts 1 to 15 ) of any colour and finish in all shades and designs, set over base coat of cm ( 1:3 ) 12 mm thick with cement slurry of honey like consistency spread at the rate of 3.30 kgs per sqm and jointed with white cement paste mixed with pigment of matching shade to full depth, including cost of all materials like tiles, cement, sand and water etc., complete including seigniorage charges, etc., complete for finished item of work. 80.00 flooring with non skid ceramic floor tiles of size 300 x 300 mm and thickness between 7 8 mm 1st quality conforming to is:13711, is:13712, is:13630 ( parts 1 to 15 ) of any colour and finish in all shades and designs, set over base coat of cement mortar ( 1:8 ) , 12 mm thick over cc bed already laid or rcc roof slab, including neat cement slurry of honey like consistency spread @ 3.3.kgs per sqm & jointed neatly with white cement paste to full depth mixed with pigment of matching shade, including cost of all materials like cement, sand water and tiles etc., complete, including seigniorage charges, etc., complete for finished item of work. 20.00 supplying and fixing indian make flat back white glazed wash hand basin ( hsw / parryware / neycer ) ist quality confirming to is: 2556 part 4 :1972 of size 550 x 400mm single c.p. pillar cock as approved by executive engineer with waste fittings like rubber plug, chain, 32mm nominal size c.p. fitting with parallel pipe thread confirming to is : 2963 1979 and fitted with 15mm nominal bore chromium plated pillar tap of 1st quality indian make 300grams seico / esso or equivalent complete with standard ci brackets including wooden block and painting to all iron fittings with 2 coats of synthetic enamel paint of approved colour and make including cutting the walls wherever necessary and making the same good for finished item of work. 15.00 supply and fixing in position 584.2mm long orrisa pan with 100 mm p or s trap including providing brick masonary seat using 2 nd class bricks as per standard practice, including cutting the walls and floors and making good the same, cost and conveyance of all materials to site, labour charges etc., complete. 50.00 plastering to superstructure 12 mm thick in two coats, with a base coat of 8 mm thick in cm ( 1:6 ) prop. and top coat of 4 mm thick in cm ( 1:4 ) prop. with dubara sponge finishing, including making grooves, cost and conveyance of all materials to site, labour charges, scaffolding, curing, all other incidental and operational charges etc., complete.for finished item of work. ground floor ( apss no: 901&904 ) 20.00 supplying and fixing 12.70 mm dia angle stop cock 400 grams indian make heavy duty of approved isi brand including cost and conveyance of all materials to site, labour etc., complete for finished item of work. 40.00 supplying and fixing 12.70 mm dia cp short body bib tap 400grames indian make heavy duty of approved isi brand including cost and conveyance of all materials to site, labour etc., complete for finished item of work. 20.00 supplying and fixing best indian make 609.6x457.2mm t.v shape mirror with plastic frame mirror including wooden blocks, screws etc., including cost and conveyance of all materials to site, labour charges etc., for finished item of work complete. 90.00 stainless steel fly proof wire mesh of not less than 20 gauge bmt f.19 50.00 providing and fixing 30mm thick brand factory made bothside prelam solid panel pvc door shutter consisting of frame made out of ms. tubes of 19gauge thickness and size of 19mmx19mm for stiles, top and bottom rails. ms. frame shall have a coat of steel primers of approved make and manufacture. ms. frame covered with 5mm thick heat moulded prelam pac „c‟ channel of size 30mm thickness, 70mm width out of which 50mm shall be flat and 20mm shall be tapered in 450 angle on either side forming stiles; and 5mm thick, 95mm wide prelam pac sheet out of which 75mm shall be flat and 20mm shall be tapered in 450 on the inner side to form top and bottom rail 115mm wide prelam pac sheet out of which 75mm shall be flat and 20mm shall be tapered on both sides to form lock rail. top, bottom and lock rail shall be provided either side of the panel. 10mm ( 5mmx2 ) thick, 20mmwide cross pac sheet shall be provided as gap insert for top and bottom rail. panelling of 5mm thick both side prelam pac sheet to be fitted in the ms. frame welded / sealed to the stiles & rails with 7mm ( 5mm+2mm ) thick x 15mm wide pac sheet beading on inner side, and joined together with solvent cement adhesive etc. an additional 5mm thick pac strip of 20mm width is to be stuck on the interior side of the „c‟ channel using pac solvent cement adhesive etc. complete as per direction of engineer – in charge, manufacture specification and drawing. bmt n.03 400.00 painting to new walls with 2 coats of plastic emulsion paint of approved brand and shade over a base coat of appropriate primer of approved brand, making 3 coats in all to give an even shade after thourughly brushing the surface to remove all dirt and remains of loose powdered materials, including cost and conveyance of all materials to work site and all operational, incidental, labour charges etc. complete for finished item of work as per ss 911 for internal walls 50.00 painting to new iron work two coats with synthetic enamel paint of approved brand and shade over one coat of red oxide primer coat ( total 3 coats ) including cost and conveyance of all materials to site , all incidental , operational & labour charges for preparing and cleaning the surface of dirt with soap and brushes , including putty , etc . , complete for finished item of work . ( apss no . 1201 , 1207 , 1212 ) . 6.00 supply and transportation of 20w led street light luminaire made of pressure diecast alluminium body with powder coated, having protective toughned glass, supply input voltage 120 270 v ac, p.f > 0.90, high power leds having system efficacy > 110 lm / w and junction temprature < 70°c, with ingrees protection ip66, luminaire performance complies to is 10322 ( part 5 / sec 3 ) , driver surge protection 4kv, external surge protection 10 kv with optics distribution , thd<10% at 110 volts ac, driver efficiency >90%, cct: 3000k 5700k, minimum cri>70, etc., complete make : philips ( green line ) / geventure / crompton ( hawk ) / bajaj ( edge+ ) 6.00 fixing of led street light luminary with 1.0 mtr., 25mm dia gi pipe bracket and anti tilting ms flat etc., including giving connections and labour charges etc., complete. 25.00 supply of 48 ( 1200mm ) sweep , 5 star rated ceiling fan, with double ball bearings , power input not more than 53w , air delivery more than 218 cubic meter / min and service value 4.11, but without regulator including cost and conveyance of all materials etc. complete. make: crompton / orient. 25.00 labour charges for fixing of ceiling fan and regulator including transportation and giving connections with twin core wire etc., complete. 20.00 supply and transportation of 18w, 1800 lumens, t8, 1200mm length led patty type tube light, input voltage ac 220 260 volts with pf>0.9, surge protection: kv, thd<15%, with inbuilt driver and frosted cover cct: 3000k 5700k, minimum cri>70, .etc., complete makes: phillips / ge / crompton. 20.00 fixing of 18w led tube light luminaire on wall / ceiling with all accessories including giving connections and all labour charges etc., complete. 5.00 supply and transportation of 12w down lighter recessed / surface mounting made of diecast alluminium body with powder coating, acrylic diffuser with driver, operating voltage range of 150 to 265 volts ac, power factor > 0.9 high power leds having efficacy of > 120 lumins / watt etc., complete with 3 years warranty. make : phillips / ge / crompton / vin / bajaj / havells. elec 3.9.1 c 10.00 supply and fixing of 16 / 20a modular 1 way combi socket with shutter and 16a / 20a 1 way modular switch duly recessed in wall with 3 modular box and 3 modular cover frame including earth connections and all labour charges etc., complete. make: legrand arteor / carbtree murano / gm zenova / 100.00 supply and run of 1 of 14 / 0.3mm ( 1.0 sq.mm ) frls / zhfr p.v.c. insulated 1100v grade as peris:694 / 1990 specification for insulated flexible copper cable in existing pipe for earth continuity including all labour charges etc., complete. [ for earth lead to circuit mains, power sockets ] . mmake: finolex / rr kable / havells. 100.00 supply and run of 2 of 36 / 0.3mm ( 2.5 sq.mm ) frls / zhfr pvc insulated 1100v grade as peris:694 / 1990 specification for copper cable in existing pipe for mains inlcuding all labour charges etc., complete. [ from distribution board to power sockets and computer boards ] . make: finolex / rr kable / havells. 20.00 supply and fixing of 6 / 10a 3 / 2 pin modular plug socket with 6 / 10a one way modular switch control on a common switch board covered with 3 module cover frame including earth con and including wire leads, earth connections along with all labour charges etc., complete. 50.00 supply and fixing of batten holder / slanting holder in lieu of ceiling rose of light point complete with all connections and all labour charges with 7w led, 490lumens bulb ( for new installation ) . 40.00 wiring with 2 runs of 14 / 0.3mm ( 1.0 sq.mm ) fire retardant low smoke frls / hffr pvc insulated 1100v grade as peris:694 / 1990 specification flexible copper cable in existing pipe with 6a one way modular switch with 6 modular cover frame, 3 plate ceiling rose including all labour charges etc., complete for light, bell, fan and exhaust fan points in non residential buildings. 50.00 supply and laying of ashirvad / ajay / astral flow guard or equivalent cpvc pipes and fittings to meet the requirement of astm d 2846 and are produced in cts ( copper tube sizes 1 / 2 to 2 ) ashirwad flowguard sdr 13.5 pipes are made from identical cpvc compounds having the same physical properties for hot and cold water ( is 15778 2007 ) 22.20 mm od pipes sdr 13.5 120.00 supply and laying of ashirvad / ajay / astral flow guard or equivalent cpvc pipes and fittings to meet the requirement of astm d 2846 and are produced in cts ( copper tube sizes 1 / 2 to 2 ) ashirwad flowguard sdr 13.5 pipes are made from identical cpvc compounds having the same physical properties for hot and cold water ( is 15778 2007 ) 28.60 mm od pipes sdr 13.5 30.00 granolithic concrete flooring 20 mm thick with ( 1:1:2 ) , using 6mm to 12 mm size hard granite machine crushed metal laid over cc bed already laid or rcc roof slab, in alternate panels of size not exceeding 1.50 m x 1.50 m and finishing the top surface to required smoothness and slopes and thread lining including cost of all materials like cement, metal, sand and water etc., complete, including seigniorage charges, etc., complete for finished item of work, 3.00 pcc ( 1:5:10 ) prop. using 40mm gauge hard granite metal from approved quarry with hand mixing including cost and conveyance of all materials to site, labour charges for laying, ramming, curing etc., complete for foundations and under stone slab flooring for finished item of work. ( apss no 402 ) . 5000.00 providing and placing on terrace polythelene water storage tanks ( at all floor levels ) double layer approved brand conforming to is12701 1996 and mnufacture with cover and suitable locking arrangements making necessary holes for inlet & outlets and overflow pipes but without fittings & base support for tanks, making good the same to ensure leak proof with an appropriate masonary platform including cost and conveyance of all materials to site, labour etc., complete for finished item of work as directed by the engineer in charge 150.00 providing roofing with 0.50 mm thick galvanized / pre painted g.i profiled sheets fixed to the purlins with 14 size self drilling screws with neoprene washer. side laps are stiched with self tapping / drilling screws. end laps are to be sealed with 25 x 3 mm butyl tape. the sheets are provided with anti capillary grove including all incidental & operational charges cost and conveyance of all materials to site etc., complete for finished item of work. 3.00 supplying and fixing 20 mm nb size gm gate ( peet ) valve as per is 778, class i, indian make heavy type, including cost and conveyance of all materials to site, labour etc., complete for finished item of work. 6.00 supplying and fixing 25 mm nb size gm gate ( peet ) valve as per is 778, class i, indian make heavy type, including cost and conveyance of all materials to site, labour etc., complete for finished item of work. 100.00 supplying and fixing ms pipes and tubes for vertical support column pipes and for roof truss made with ms pipes and tubes as per approved drawing or as directed by the engineer in charge, including cost and conveyance of all materials to site and labour charges for fabrication , fixing etc., complete for the finished item of work . 200.00 white washing 3 coats with white cement to ceiling of approved quality to give an even shade after thoroughly brushing the surface to remove all dirt and remains of loose powdered materials including cost of all materials, labour charges and incidental such as scaffolding, lift charges etc., complete for finished item of work, but excluding conveyance charges of materials...

Tirumala Tirupati Devasthanams - Andhra Pradesh

30522322 miscellaneous works at old dpw stores near alipiri tirupati. 40.00 dismantling ac or gi sheet roofing including ridges, rafters and purlins etc., and carefully stacking useful materials for reuse. dismantling ac or gi sheet roofing including ridge dismantling ac or gi sheet roofing including ridge na 10.02 0.50 demolition including stacking of serviceable materials and disposal of unserviceable materials within 100 metres lead brick work demolition including stacking of serviceable mater demolition including stacking of serviceable mater na 268.33 130.00 dismantling, clearing away and carefully stacking materials useful for re use thorough scraping of old plastered surface dismantling, clearing away and carefully stacking dismantling, clearing away and carefully stacking na 6.16 3.00 earthwork excavation for foundations and depositing on bank for all lifts and with an initial lead of 10m including all operational, incidental, labour charges such as shoring, sheeting, planking, strutting etc., complete for finished item of work ordinary soil manual means up to 3m depth. note: cost of dewatering may be added, where required, up to 5% of labour cost. assessment for dewatering shall be made as per site condition. earthwork excavation for foundations and depositi earthwork excavation for foundations and depositi na 238.81 6.00 cement concrete ( 1:4:8 ) using 40 mm ( 0.54 cu.m ) , 20 mm ( 0.27 cu.m ) and 12 mm ( 0.09 cu.m ) nominal size hard broken granite crushed metal from any source conforming to the relevant isi standards for foundations etc., laid in layers of not more than 15 cm thick well compacted including curing, machine mixing, cost and conveyance of all materials etc., complete. note: measurement boxes shall be used for measuirng the quantities of cement, aggregate and water required for the given concrete mix. cement concrete ( 1:4:8 ) using 40 mm ( 0.54 cu.m ) , 2 cement concrete ( 1:4:8 ) using 40 mm ( 0.54 cu.m ) , 2 na 4, 127.61 2.00 cement concrete ( 1:2:4 ) using 20 mm ( 0.54 cu.m ) , 12 mm ( 0.36 cu.m ) nominal size hard broken granite crushed metal from any source conforming to the relevant isi standards for foundations etc., laid in layers of not more than 15 cm thick well compacted including centring charges, curing, machine mixing, cost and conveyance of all materials etc., complete. note: measurement boxes shall be used for measuirng the quantities of cement, aggregate and water required for the given concrete mix. cement concrete ( 1:2:4 ) using 20 mm ( 0.54 cu.m ) , 1 cement concrete ( 1:2:4 ) using 20 mm ( 0.54 cu.m ) , 1 na 6, 796.35 5.50 construction of brick masonry in cm ( 1:6 ) using well burnt bricks 2nd class or ground moulded ( non modular or traditional size ) ( 230 x 110 x 70 mm ) including curing, cost and conveyance of all materials as directed during execution and complying with standard specifications etc., complete. construction of brick masonry in cm ( 1:6 ) using w construction of brick masonry in cm ( 1:6 ) using w na 5, 958.52 0.00 plastering in cm using best river sand from approved quarry including cost and conveyance of all materials, screening, curing, rounding of corners, incidental charges as directed during execution complying with standard specifications etc., complete for the following proportions plastering in cm using best river sand from appro plastering in cm using best river sand from appro na 0.00 30.00 do in cm ( 1:5 ) 12 mm thick do in cm ( 1:5 ) 12 mm thick do in cm ( 1:5 ) 12 mm thick na 223.37 75.00 do in cm ( 1:5 ) 20 mm thick do in cm ( 1:5 ) 20 mm thick do in cm ( 1:5 ) 20 mm thick na 346.89 200.00 supply and fixing of ms tubes & pipes of all diameters as per ls 1161, including labour charges for fabricating all heavy steel works like trusses, stanchions, heavy beams and girders including cost of welding rods, power charges, etc and labour charges for fixing heavy iron grills, trusses, etc., complete in position, including painting the grills with two ( 2 ) coats with ready mixed synthetic enamel paint in all shades grade 1 having voc ( volatile organic compound ) content less than 50 grams / liter, approved colour and make, over a priming coat with ready mixed red oxide metal primer paint, total three ( 3 ) coats, including cost and conveyance of all materials, including brushes to have smooth finish, as directed during execution complying with standard specifications etc., complete supply and fixing of ms tubes & pipes of all diame supply and fixing of ms tubes & pipes of all diame na 116.48 35.00 painting priming coat with ready mixed cement primer ( water thinnable ) for interior grade i for old plastered surface including cost and conveyance of all materials including brushes to have smooth finish as directed during execution. painting priming coat with ready mixed cement prim painting priming coat with ready mixed cement prim na 40.98 5.80 painting priming coat with ready mixed cement primer ( water thinnable ) for exterior grade 2 for old plastered surface including cost and conveyance of all materials including brushes to have smooth finish as directed during execution. painting priming coat with ready mixed cement prim painting priming coat with ready mixed cement prim na 43.50 110.00 painting two ( 2 ) coats for old internal walls, with acrylic emulsion paint interior grade having voc ( volatile organic compound ) content less than 50 grams / liter of approved brand and shade after thoroughly brushing the surface to remove all dirt and remains of loose powdered materials, including cost and conveyance of all materials to work site and all operational, incidental, labour charges etc., complete for finished item of work as per ss 911 for internal walls. painting two ( 2 ) coats for old internal walls, wit painting two ( 2 ) coats for old internal walls, wit na 63.01 150.00 painting two ( 2 ) coats for old external walls, with acrylic emulsion paint exterior grade with silicon additives having voc ( volatile organic compound ) content less than 50 grams / liter of approved brand and shade after thoroughly brushing the surface to remove all dirt and remains of loose powdered materials, including cost and conveyance of all materials to work site and all operational, incidental, labour charges etc., complete for finished item of work as per ss 911 for external walls. painting two ( 2 ) coats for old external walls, wit painting two ( 2 ) coats for old external walls, wit na 100.74 60.00 painting two ( 2 ) coats for new external walls, with acrylic emulsion paint exterior grade with silicon additives having voc ( volatile organic compound ) content less than 50 grams / liter of approved brand and shade over a priming coat with ready mixed cement primer ( water thinnable ) of exterior grade 2, total three ( 3 ) coats after thoroughly brushing the surface to remove all dirt and remains of loose powdered materials, including cost and conveyance of all materials to work site and all operational, incidental, labour charges etc., complete for finished item of work as per ss 911 for external walls. painting two ( 2 ) coats for new external walls, wit painting two ( 2 ) coats for new external walls, wit na 216.36 370.00 supply and fixing of ms structural steel, i.e., angles, channels and i sections, including labour charges for fabricating steel works like window grills, compound wall grills, iron doors, windows including cost of welding rods, power charges, etc and labour charges for fixing grills etc., complete in position, including painting the grills with two ( 2 ) coats with ready mixed synthetic enamel paint in all shades grade 1 having voc ( volatile organic compound ) content less than 50 grams / liter, approved colour and make, over a priming coat with ready mixed red oxide metal primer paint, total three ( 3 ) coats, including cost and conveyance of all materials, including brushes to have smooth finish, as directed during execution complying with standard specifications etc., complete supply and fixing of ms structural steel, i.e., an supply and fixing of ms structural steel, i.e., an na 105.41 1700.00 supplying and fixing in position m.s ornamental grills for windows and ventilators or for veranda openings using m.s. flats, square rods, angles sheets etc., of approved design including necessary cuttings, bending fabrication, welding, grinding and finishing smooth including painting the grills with two coats with synthetic enamel paint gr i over a primary coat ( red oxide metal primer ) ( total three coats ) of approved make and colour including cost of making the holes into rcc or masonry works and making good the same wherever necessary, including cost and conveyance of all materials, incidental charges etc., complete. supplying and fixing in position m.s ornamental g supplying and fixing in position m.s ornamental g na 105.68 40.00 supply and fixing of galvalume sheet pre painted galvalume trapezoidal profile roofing sheets with 0.47mm thickness ( total coated thickness tct ) , coating: alu zinc coating az150 gsm. tensile strength: 550 mpa. paint coating: regular modified polyester painting. painting thickness ( top ) : 18 to 20 microns, ( bottom ) : 5 to 7 microns. sheet width: 1.020, length: maximum 12 meters with regular range colours with minimum end lap of 15 cms etc., complete as directed during execution ( original coil shall be of make tata blue scope / jsw ) supply and fixing of galvalume sheet pre painted g supply and fixing of galvalume sheet pre painted g na 593.81 150.00 supply and fixing of stainless steel ss 304 grade tubes, sections, plates, sheets and pipes of all sizes and diameters etc., including cost and conveyance of all materials and labour charges for fabrication of stainless steel railing works using ss welding rods including buffing, polishing, lacquer finishing, to present seamless finishing etc., complete as directed during execution supply and fixing of stainless steel ss 304 grade supply and fixing of stainless steel ss 304 grade na 512.81 0.00 supply of semi skilled work men ( 2nd class ) / unskilled work men, as and when required, as directed during execution. supply of semi skilled work men ( 2nd class ) / unsk supply of semi skilled work men ( 2nd class ) / unsk na 0.00 15.00 do semi skilled work men ( 2nd class ) mason / brick layer / stone cutter / carpenter / plumber do semi skilled work men ( 2nd class ) mason / do semi skilled work men ( 2nd class ) mason / na 702.94 25.00 do unskilled work men man mazdoor / woman mazdoor do unskilled work men man mazdoor / woman ma do unskilled work men man mazdoor / woman ma na 656.08 30.00 supply and fixing of glow sign radium stickers name plate / sign ( or ) instruction boards using 3mm thick acrylic white sheet as back ground and glow sign radium sticker one layer for letters of different sizes as directed during execution including cost of 3mm thick acrylic sheet, radium sticker and all labour charges for computer design and cutting, pasting and fixing the boards to walls. supply and fixing of glow sign radium stickers nam supply and fixing of glow sign radium stickers nam na 143.53 450.00 labour charges for laying & fixing of precast concrete blocks for paving of all grades, any thickness, all sizes & shapes including all labour charges for loading & unloading, laying to desired lines and levels complete excluding cost of cement, sand, water, electricity etc., complete. labour charges for laying & fixing of precast conc labour charges for laying & fixing of precast conc na 254.40 1800.00 supplying and fixing galvanized steel barbed wire ( is:278 1978 weighing 9.38 kg per 100 metres ( min ) , straining and fixing to any type of standard, rails, staining bolts, including securing with and provision of galvanized mild steel wire, staples or steel pins, etc., as directed ( posts and struts of wood, concrete, steel etc., ) and straining bolts shall be paid for separately type a iowa & type b glidden type designation as per standard specification supplying and fixing galvanized steel barbed wire supplying and fixing galvanized steel barbed wire na 11.65 15.00 conveyance charges for machinery for transporting earth / sand / gravel / murrum / lime / surki by tippers and trucks including loading, unloading and idle hire charges with a lead up to 5 km etc., complete as directed during execution. conveyance charges for machinery for transporting conveyance charges for machinery for transporting na 96.30 rupees six lakh ( s ) fifty three thousand three hundred eighty six only...

Hindustan Petroleum Corporation Limited - Andhra Pradesh

30383427 tender for building repair works site clearance and dismantling: dismantling and clearing of any site for further construction, supplying and laying plain cement concrete of volumetric mix 1:2:4 (1 cement: 2 sand: 4 coarse aggregates) using 43/53 grade ordinary portland cement with 20 mm downgraded coarse aggregate for aprons, including shuttering if required) in foundation, screed, aprons, pits, steps, drains, footings, retaining wall, beams etc in sub structure etc., at all level as per drawings, specifications and instruction of engineer, supply and laying of vitrified floor tiles (premium quality vitrified tiles of approved brand of approved make or approved equivalent) of size 600 mm x 600 mm, in approved shades/design, as directed by the engineer in charge, including 20 mm (average thickness) bed mortar in cement mortar 1:6, cement slurry, leveling, grouting of joints with matching color cement etc complete., providing and applying two coats of ''premier plastic/acrylic emulsion paint'' of hpcl approved make and colour/shade over a coat of water based primer including preparation of surface by thorough cleaning as per manufacturers specification fully to give an even shade as approved and curing as per manufacturers specifications and as directed. item to include all accessories, tools and labour, men material and lift upto 5 meters., scaffolding with all cleaning, depropping, clearing complete. item to include getting mock up for 2 sq.m area approved by architect/engineer in charge...

Hindustan Shipyard Limited - Andhra Pradesh

30193424 procurement of paints and misc items for colony procurement of paints and misc items for colony , exterior weather proof emulsion paint , gi barbed wire of 12mm guage , thinner for enamel paint ename thinner for enamel paints , golden yellow enamel paint synthetic enamel golden yellow paint , balck and blue enamel paint white synthetic enamel paint , white cement white synthetic enamel paint , paint brush 3 inch 3 inch brush , paint brush 4 inch 3 inch brush , paint brush 6 inch 3 inch brush...