33523723
provision of deficient sailors married accommodations at certain places at visakhapatnam 1 surface dressing not exceeding 15 cm deep and getting out in soft / loose soil complete all as specified and as directed. 2 rough excavation not exceeding 1.5m deep and getting out in soft / loose soil complete all as specified and as directed. 3 excavation in trenches not exceeding 1.5m wide and not exceeding 10 sq.m on plan area and not exceeding 1.5m deep in soft / loose soil complete all as specified and as directed. 4 excavation in trenches not exceeding 1.5m wide and not exceeding 10 sq.m on plan area and depth exceeding 1.5m but not exceeding 3.0m and getting out in soft / loose soil complete all as specified and as directed. 5 removal of excavated material [ soil ] to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and as directed. 6 removal of excavated material [ soil ] to a distance exceeding 250 m but not exceeding 500m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and as directed. 7 returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25cm thick of excavated soil complete all as specified and as directed. note: a deduction of 10% shall be made from total computed volume of filling to cater in bulk irrespective of machinery used for ramming. 8 m & l for pcc 1:4:8, type d 2, using 40mm graded stone aggregate as in foundation, fillings, mass concrete, footings etc complete all as specified and as directed. 9 m & l for rcc m–30 design mix, using 20mm graded stone aggregate as in foundations including rafts, footings, foundation beams, plinth beams, bases for columns etc. complete all as specified and as directed. 10 use and removal of steel formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits [ if any ] of foundation and plinth beams and similar work, vertical or to batter for rough finished surfaces complete all as specified and as directed. 11 m & l for rcc m 30 design mix, using 20mm graded stone aggregate as in columns, pillars, piers, posts and struts etc. complete all as specified and as directed. 12 use and removal of steel formwork to sides of pillars, posts, struts, piers, columns and stanchions of any shape / cross section for rough finished surfaces of concrete complete all as specified and as directed. 13 m & l for rcc m 30 design mix, using 20mm graded stone aggregate as in beams, cantilevers, bressummers, lintels over 1.5m span etc complete all as specified and as directed. 14 use and removal of steel formwork to sides and soffits of floor or roof beams, beam launchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc, splays between floors and beams and similar works for rough finished surfaces of concrete complete all as specified and as directed. 15 m & l for rcc m 30 design mix, using 20mm graded stone aggregate as in slabs supported on walls, beams, columns, landings, shelves and the like complete all as specified and as directed. 16 use and removal of steel formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work not exceeding 200mm thick [ horizontal or sloping ] including rough finished surfaces complete all as specified and directed. 17 s & f reinforcement using high strength corrosion resistant deformed tmt bars of grade fe–500d of 10mm dia and over, cut to length, bent to shape required including cranking, bending, spirally for hooping, hooking ends and binding with annealed mild steel wire not less than 0.9mm dia or securing with clips or welded complete all as specified and as directed. 18 s & f reinforcement using high strength corrosion resistant deformed tmt bars of grade fe–500d of 5mm to 10mm dia bars as in stirrups, spacers and binders, cut to length, bent to shape required including cranking, bending, spirally for hooping, hooking ends and binding with annealed mild steel wire not less than 0.9mm dia or securing with clips or welded complete all as specified and as directed. 19 s & f gi wire cloth / mesh with2 mm dia of wire and fixed with tinned tacks or stainless steel wire staples as in lateral reinforcement for pre fabricated concrete wall panels / modules all as per manufacturers instructions, as specified and as directed. 20 m & l for providing pre fabricated reinforced concrete wall panels / modules with hollow infill patterns, light weight with acoustic properties duly factory fabricated through computer aided automated 3d printing technology with desired models / patterns / logos, etc. as per the drawings provided by the engineer in charge for the building. the pre fabricated 3d wall panels shall be cast off site in layer by layer with layer thickness of 15 20mm each and layer width of 30 35mm, including transportation from off site to on site, installed and assembled in position all as per manufacturers instructions, as specified and as directed.notes: [ a ] the pre fabricated reinforced concrete wall panels / modules with any sort of design as per the drawings provided shall be procured and installed through specialist firms viz. m / s. micob pvt ltd., ( gandhi nagar, gujrat ) / m / s. tvasta manufacturer solutions pvt ltd. ( chennai ) . necessary mou shall be entered with any of the specialist manufacturer as mentioned above to provide technical support and to provide trained persons for supervision of the work and the same shall be submitted alongwith the tender documents [ t bids ] . if any tenderer fails to produce mou, their bid shall be rejected and their financial bid shall not be opened. [ b ] an authorised person of the specialist manufacturer of the panels shall be made available by the contractor at site for co ordination with the department as well as with the off site manufacturing unit for smooth execution of the work including supervision of work at site at every stage of work without hampering the desired progress of the work. [ c ] the size and shape of the panels shall vary according to the site requirement during execution of the work and the contractor shall be required to quote the rate accordingly and nothing extra shall be allowed on this account. [ d ] the contractor shall submit necessary design details and requisite manufacturers test certificates in respect of the 3d printed wall panels / modules prior to incorporation of the same at site. 21 [ e ] the fabrication of concrete 3d printed wall panels shall be commenced only after conforming the strength parameters of the walls with respect to m 30 design mix strength. the composition of materials for 3d printed walls shall be as follows: ( i ) opc 53 grade cement ( not less than 550 kg / cum ) ( ii ) fly ash ( not less than 300 kg / cum ) ( iii ) quartz m sand ( not less than 1000 kg / cum ) ( iv ) silica fumes / fibers to improve the buildability, extrudability and flowability ( not less than 180 kg / cum ) ( v ) water ( not less than 300 litres / cum ) ( vi ) super plasticizers viscosity modifying agent ( not less than 35 litres / cum ) ( vii ) galvanised steel wire mesh with 2mm dia wires as in lateral reinforcement placed in horizontal position at every 300mm height to increase tensile and flexural strength. ( viii ) fe 500d anti corrosive tmt reinforcement bars shall be used as main reinforcement with 30mm nominal cover in semi automatic method of 3d printing without hampering the printing speed. [ spacing of bars shall be as per the detailed drawing provided at the time of execution ] [ f ] all safety measures shall be ensured while transportingthe wall panels from off site to on site and the wall panels shall be transported only after attaining the target mean strength in accordance with m 30 design criteria. [ g ] each wall panel shall be provided with suitable anchorage for lifting and installing in position. suitable capacity of crane, trailer, lifting arrangements shall be provided by the contractor for handling of the panels at both off site and on site. [ h ] the weight of each panel / module shall not exceed 700 kg. [ i ] the wall panels shall be with 40% rustic finish. 22 [ j ] the panels shall be compatible to mechanical, electrical and plumbing systems to be accommodated in the building and accordingly the panels shall be fabricated in the factory as per the drawings provided or as directed by the engineer in charge as per site requirement. [ k ] the tmt bars provided as main reinforcement and wire mesh provided as lateral reinforcement shall be measured and paid separately under relevant items of this schedule / boq. [ l ] the contractor shall submit psmb duly marked with the location for record. [ m ] site visit to the manufacturer’s workshop / factory shall be made by the departmental executive staff authorized by the accepting officer during fabrication of wall panels and at the time of delivery of each lot to check the manufacturing process and to determine the strength parameters of the panels. [ n ] quality assurance plan shall be submitted by the contractor to the accepting officer for approval within 15 days from the date of commencement. 23 [ o ] the contractor shall furnish a written guarantee to ge from the specialist firm engaged by him for a period of 25 years from the certified date of completion by the ge for the effectiveness of the 3d printed wall panels supplied and installed in the subject work on non judicial stamp paper of ? 100.00. during the aforesaid guarantee period of 25 years, the contractor shall be solely responsible for the effectiveness of the 3d printed wall panels. any sign of cracks or defects of any type noticed by the ge during this period shall be promptly rectified by the contractor without any extra cost to the government. the above provision shall not however, absolve the contractor of his responsibility of effectiveness of the 3d printed wall panels as required under the provisions of contract. should the ge, at any time during construction or reconstruction or prior to the expiration of guarantee period of 25 years after the 3d printed wall panel work has been completed as per contract, finds that any building / structure showing any sign of cracks or defects of any type, the contractor shall, on demand in writing from the ge specifying the location complained of notwithstanding that the same may have been inadvertently passed / certified and paid for, forthwith undertake to carry out such treatment as may be necessary to render the structure [ s ] free from cracks or defects at his own expenses for a period of 25 years from the certified date of completion. in the event of his failing to do so, within the period as specified by the ge in his demand aforesaid, the ge may undertake such rectifications as may be necessary through other agency at the risk and expense in all respects of the contractor. the liability of the contractor under this condition shall not extend beyond the period of 25 years from the certified date of completion, unless the ge had previously given notice to the contractor. 24 [ p ] a security deposit against the guarantee period for effectiveness of the 3d printed wall panels supplied and installed in the subject work for 25 years shall be calculated @ 5% of the amount of 3d printed wall panels priced at contract rates and shall be retained by the government from the contractor’s dues. this amount shall be refunded to the contractor after the expiration of the guarantee period of 25 years from the certified date of completion by the ge, provided always that the contractor shall first have been paid the final bill and have rendered no demand certificate [ iafa – 451 ] . alternatively, the contractor may furnish fixed deposit receipt in lieu of security deposit from a schedule bank in favour of ge for the above said guarantee period. condition 10, 46 & 68 of general conditions of contracts [ iafw – 2249 ] shall be deemed to be amended to the extent mentioned above. [ q ] any minor constructional details not specified elsewhere but which are essential for execution and completion of work including all incidental charges shall also be deemed to be considered by the contractor and the rate quoted shall be deemed to include for all the above provisions no extra claims shall be allowed by the department. 25 m & l for 40 mm thick pcc 1:2:4, type b 0, using 12.5mm graded aggregate as in padding over roof slabs, surface finished fair and even without using extra cement complete all as specified and as directed. 26 m & l for preparing the surfaces of concrete roof and brushing neat cement slurry with 3.0 kg of cement per sq.m area, rendering 10mm thickin cement mortar 1:3 on concrete surfaces finished even and smooth without using extra cementincluding mixing of water proofing compound of approved make as per manufacturers instructions for levelling the surface smooth to receive the water proofing membrane, priming the surface with a coat of cold applied bituminous primer @ 0.50 kg per sq.m, applying a coat of blown bitumen of grade 85 / 25 @ 1.2 kg per sq.m, laying polymeric water proofing membrane of weight not less than 3.00 kg per sq.m reinforced with polyester non woven fabric of weight notless than 150 grams per sq.m, by torch application with side over lap of 100mm & end over lap of 150mm & tucked into the chases on vertical surfaces by thermo fusion including applying a coat of blown bitumen of grade 85 / 25 @ 1.2 kg per sq.m and finished with a coat of bituminous aluminium paint @ 100 grams per sq.m on top for water proofing treatment completecomplete all as specified and as directed. note: water proofing compound will be measured and paid separately. 27 m & l for rendering to brick / concrete surfaces, 10 mm thick in cement mortar 1:6, surfaces finished even and smooth without using extra cement complete all as specified and as directed. 28 m & l for rendering 5mm thick in cement mortar 1:4 including mixing water proofing compound as per manufacurers instructions over a backing coat of 10mm thick in cm 1:6 on concrete or brick masonry surfacesand finishing the top surface even and smooth without using extra cement complete all as specified and as directed.note: water proofing compoundwill be measured and paid separately. 29 supply only integral water proofing compound [ isi marked ] of approved make. 30 m & l for rendering 5 mm thick in cement mortar 1:3 on fair faces of concrete surface of ceiling surfaces finished even and smooth without using extra cement complete all as specified and as directed. 31 demolition of cement concrete of any description and in any position not otherwise specifically provided for and removing rubbish to a distance not exceeding 1.50 km complete all as specified and as directed. 32 m & l for two coats of weather proof exterior emulsion paint [ 100% acrylic ] by using auto roller / airless sprayer over a coat of exterior primer of same manufacturer as that of paint on newly plastered walls / ceiling, pillasters, bands, borders, soffits of chajjas and projections including necessary preparation of surfaces by using vaccume based sanding machine complete all as specified and as directed. 33 m & l for preparing newly plastered ceiling surfaces and applying threecoats of white washing complete all as specified and as directed. 34 m & l for preparing newly plastered wall surfaces by using vaccume based sanding machineandapplying two coats of acrylic washable distemper by using auto roller / airless sprayer, over a coat of alkali resistant primer over two or more coats of cement based wall care putty on walls by using multipurpose mixture for proper mixing of putty and putty sprayer for application of putty including rubbing with sand paper to obtain a smooth surface and making good any undulations on the wall surfaces complete all as specified and as directed. 35 m & l for vitrified tiles, double charged, coloured, premium quality, of size not exceeding 0.36 sq.m, 10 mm thick as in floors, set and jointed in cement slurry and pointed flush using polymer based cementitious tiling joint filler to match the shade of the tile including screed bed or bedding layer of mortar 15 mm thick in cement mortar 1:4 complete all as specified and as directed. note: the colour / shade / design of tiles shall be as approved by ge. 36 m & l for vitrified tiles, double charged, coloured, premium quality, of size not exceeding 0.36 sq.m, 10 mm thick as in skirting and dado, set and jointed in cement slurry and pointed flush using polymer based cementitious tiling joint filler to match the shade of the tile over backing coat of 10mm thick in cement mortar 1:3 complete all as specified and as directed. note: the colour / shade / design of tiles shall be as approved by ge. 37 m & l for non skid ceramic tiles, joint free, coloured, premium quality of size exceeding 0.11 sq.m and not exceeding 0.18 sq.m, 7 to 8 mm thick [ square or rectangular ] as in floors etc, set and jointed in neat cement slurry and pointed flush using polymer based cementitious tiling joint filler to match the shade of the tile including screed bed or bedding layer of mortar 15 mm thick in cement mortar 1:4 complete all as specified and as directed. note: the colour / shade / design of tiles shall be as approved by ge. 38 m & l for joint free glazed ceramic tiles, edge cut, concept type, coloured, premium quality, of size 450 mm x 300 mm, 7 to 8 mm thick as in vertical surfaces such as skirting, dado etc set and jointed in neat cement slurry and pointed flush using polymer based cementitious tiling joint filler to match the shade of the tile over backing coat of 10mm thick in cement mortar 1:3 complete all as specified and as directed. note: the colour / shade / design of tiles shall be as approved by ge. 39 s & f gi water tubing of 15 mm bore, medium grade conforming to is 1239 [ part 1 ] including all fittings such as bends, tees, short pieces, connectors, elbows, reducers, union, sockets etc fixed to walls, ceiling or laid on floors including testing complete all as specified and as directed. 40 s & f gi water tubing of 20 mm bore, medium grade conforming to is 1239 [ part 1 ] including all fittings such as bends, tees, short pieces, connectors, elbows, reducers, union, sockets etc fixed to walls, ceiling or laid on floors including testing complete all as specified and as directed. 41 s & f gi water tubing of 25 mm bore, medium grade conforming to is 1239 [ part 1 ] including all fittings such as bends, tees, short pieces, connectors, elbows, reducers, union, sockets etc fixed to walls, ceiling or laid on floors including testing complete all as specified and as directed. 42 s & fvitreous china wash down water closet [ pedestal pattern ] , white, including 10 litres capacity, pvc valve less, syphonic action type, low level flushing cistern, white, with inlet ball valve, float, handle, flush pipe of polyethylene of lowor high density of pvc, 32mm dia, pvc connection of 15mm bore and 600mm long with ptmtcheck nut and union etc. including brackets and connections to pipe and flush pipe including plastic water closet seat back closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging device and p or s trap complete all as specified and as directed. 43 s & fvitreous china ware wash hand basin, white, flat back of size 450 mm x 300 mm including pillar taps, cast copper alloy, chromium plated, fancy type, 15 mm dia, with capstan head, screwed down high pressure with or with out lettered hot or cold with long screwed shanks and fly nuts screwed for iron pipe and fixed, 32mm dia brass chromium plated waste fittings with long screw shanks and fly nuts, flange end bedded in red led cement and other end fixed, rubber plug with rings including ci brackets, cutting for and pinning in ends of brackets or erecting strand, 32mm bore pvc flexible waste pipe, pvc connection of 15mm bore and 600mm long with ptmt check nut and union etc. complete all as specified and as directed. 44 s & fbib taps, 15 mm dia, brass chromium plated, fancy type with crutch or butterfly handle, screwed down for iron pipe and fixed etc. complete all as specified and as directed. 45 s & fstop valves, 15 mm dia, cast copper alloy with capstan head, chromium plated, fancy type, screwed down high pressure with crutch or butterfly handle with long shank and cup [ concealed type ] for iron pipe etc complete all as specified and as directed. 46 s & fangle cock, 15 mm dia, cast copper alloy with capstan head, chromium plated, screwed down high pressure with crutch or butterfly handle for iron pipe etc. complete complete all as specified and as directed. 47 s & f ptmt tubular towel rail, 20mm dia, d type, 600 mm long between flanges, fixed with and including chromium plated brass screws and wooden / plastic cleats [ minimum weight 190 grams ] complete all as specified and as directed. 48 s & f ptmt soap dish with screws complete all as specified and as directed. 49 s & f rotational moulded polythene [ hdpe ] water tanks, triple layered, isi marked, cylindrical & vertical type 1000 litres capacity hoisted and fixed in position including provision of 40mm / 25mm dia spouts for connecting inlet, outlet, over flow and washout pipes complete all as specified and as directed. 50 s & f ball valves, 25 mm bore, high pressure of ptmt with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe [ minimum weight 25mm 455 grams ] etc complete all as specified and as directed. 51 s & f gun metal globe or gate valve of class i, pressure tested of 1.5 mpa, 25 mm bore with iron wheel head, screwed both ends for iron pipe, conforming to is, isi marked complete all specified and as directed. 52 m & l for 40mm bore dia high density polyethylene pipes [ hdpe of pressure rating 6 kgf / sq.cm laid in trenches or fixed to walls or ceilings or in floors etc. complete all as specified 53 s & f 75mm bore pvc [ swr ] pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and as directed. 54 s & f 75mm outlet pvc [ swr ] floor trap with grating including jointing with solvent cement complete all as specified and as directed. 55 s & f 110mm bore pvc [ swr ] pipes single socketed, in any length with rubber ring joints, fixed to walls including necessary brackets, clamps complete all as specified and as directed. 56 s & f 75 mm bore pvc [ swr ] bends of any radius including jointing with solvent cement complete all as specified and as directed. 57 s & f 110 mm bore pvc [ swr ] bends of any radius including jointing with solvent cement complete all as specified and as directed. 58 s & f 75 mm bore pvc [ swr ] branch piece, single [ singley ] equal or unequal jointing with solvent cement complete all as specified and as directed. 59 s & f 110 mm bore pvc [ swr ] branch piece, single [ singley ] equal or unequal jointing with solvent cement complete all as specified and as directed. 60 s & f 110mm bore pvc [ swr ] gully trap with grating including jointing with solvent cement complete all as specified and as directed. 61 m & l for hardcore of gauge not exceeding 63mm of broken stones or boulders, deposited, spread and levelled in layers not exceeding15 cm thick watered and rolled with power road roller of 8 to 12 ton capacity and consolidated to required gradient and camber complete all as specified. 62 m & l for 75 mm thick, pcc 1:3:6, type c 1, using 20mm graded stone aggregate as in plinth protection, surfaces finished even and smooth complete all as specified and as directed. 63 s & f solid pvc door frame of size 50mmx47mm made out of 5mm plain colour pvc sheet reinforced with ms square tube in opening complete all as specified and as directed. 64 s & f factory made solid panel pvc door shutter 30 mm thick [ style ] consisting of frame made out of m.s. tubes for top & bottom rails. m.s. frame shall be covered with heat moulded plain colour pvc c channel having a pvc sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour pvc sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour pvc sheet to be fitted in the m.s. frame welded / sealed to the stiles & rails with suitable pvc sheet beading, and joined together with solvent cement fixing in frame at site as per specification complete all as specified and as directed. 65 m & l forpowder coated aluminium sections [ minimum 50 micron thick ] of approved colour as in door, window, ventilator frames, partitions with one or more rebates and door, windows shutters sliding / openable type / ventilator shutter aluminium section including necessary joining cleats, glazing clips, neoprene rubber packing, powder coated aluminium snap beading, screws and locking arrangements complete all as specified and as directed. note: [ a ] the size of aluminium sections shall be all as specified in relevant is code and mes schedule part i. [ b ] supply only panel inserts of glass / gauze / grills will be measured and paid separately. [ c ] unit rate quoted shall be deemed to include for cost of rubber beading, glazing clips, neoprene packing and fixing only of panel inserts ofglass / gauze / grills etc. 66 s & f 75mm size, butt hinges, stainless steel, medium weight, bright polished including fixtures complete all as specified and as directed. 67 s & f aluminium anodised handle, of extruded section fabricated type of size 75mm long complete all as specified and as directed. 68 s & f aluminium anodised barrel tower bolt of size 100 mm size of extruded section complete all as specified and as directed. 69 supply only powder coated aluminium deco grill of model / design no. dg 104 ( 7.2mmx4.2mm ) including powder coated aluminium channel of size 30 x 12 x 1.5mm for fixing deco grill complete all as specified and as directed. 70 supply only 5mm thick sheet glass ordinary quality in squares exceeding 0.5 sq.m in each pane complete all as specified and as directed. 71 supply only 4mm thick figured glass and glazing with oil putty or with wooden beads in squares not exceeding 0.5 sq.m in each pane complete all as specified and as directed. 72 supply onlystainless steel wire cloth / mesh with average aperture not exceeding 1.40 mm and dia of wire 0.36 mm complete all as specified and as directed. 73 s & f stainless steel wire cloth / mesh with average aperture not exceeding 1.40 mm and dia of wire 0.36 mm complete all as specified and as directed. 74 m & l for plain cement concrete type c1 [ nominal mix ] 1:3:6 using 20mm graded stone aggregate cast in situ in lintels up to 1.5m span, cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings up to 60 cm in height, copings, kneelers, apex stones, bed plates including weathering, slightly rounded or chamfered angles and throating as directed including use and waste of form work, complete all as specified and as directed. 75 m & l for two coats of synthetic enamel paint over one coat of pink primer to newly untreated wooden surfaces over 10cm width or girth including preparation of surfaces complete all as specified and as directed. 76 s & f mild steel work conforming to fe 290, grade e 165 as in bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required, hooks [ stay ] , heavy, for large gates, hook and pintle hinges, large hasps and staples, chains, hand made sliding bolts, clamps, hold fasts, wall ties, hooks for hanging fans, plain angle cleats for securing purlins to wood trusses or rafters, knee piece inserts, two way and three way straps, plate washers and similar small articles complete all as specified and as directed. 77 s & fstainless steel curtain rod, 20 mm dia with fixing brackets, end caps etc complete all as specified and as directed. 78 s & f second class hard wood, plain, solid, straight chowkats and frames, wrought, framed, rebated on the solid, rounded or chamfered, put together with glue, pinned at joints complete all as specified and directed. 79 s & f factory made, 30 mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and as directed. 80 s & f factory made, 30mm thick, second class hard wood, glazed and skeleton door shutters, open rebated and prepared to receive glass, gauze, etc. [ without sash bars ] , edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc., sizes of members of shutters as specified in ssr part – i, section 8, clause 8.24 [ a ] and fitted to chowkats complete all as specified and as directed. 81 s & f aluminium alloy anodised sliding door bolt with hasp and staple [ bolt type ] of size 250 mm and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and as directed. 82 s & f aluminium anodised barrel tower bolt of size 300 mm size of extruded section complete all as specified and as directed. 83 s & f aluminium anodised handle, of extruded section fabricated type of size 200mm long complete all as specified and as directed. 84 m & l for two coats of synthetic enamel paint over one coat of red oxide / zinc chrome primer on new steel surfaces over 10cm width or girth including preparation of surfaces complete all as specified and as directed. 85 m & l for providing pre construction anti termite treatment for the backfill in contact with foundation by applying emulsion at the rate of 7.5 litres per square metre of vertical surface [ area of the substructure in contact with back fill ] complete all as specified and as directed. 86 m & l for providing pre construction anti termite treatment for the top surface of filled earth by applying emulsion at the rate of 5 litres per square metre ofsurface complete all as specified and as directed. 87 m & l for providing pre construction anti termite treatment for the soil under plinth protection by applying emulsion at the rate of 5 litres per square metre of surfacearea complete all as specified and as directed. 88 m & l for providing pre construction anti termite treatment for the soil along with external perimeter of building by applying emulsion at the rate of 2.25 litres per running metre of the perimeter wall complete all as specified and as directed. 89 m & l for 150 mm dia rcc pipes, class np3, laid and jointed with collars laid in trenches and jointedwith cement mortar complete all as specified and as directed. 90 m & l for concrete bed to drain pipes of size 150 mm bore packing under and haunching against the sides of pipes after they are laid and fitted in cement concrete, type c2, 1:3:6, using 40mm graded stone aggregate complete all as specified and as directed. 91 s & f rolled mild steel work conforming to fe 410 w, grade e 250, quality a as in framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc complete, drilled for fixing of steel sheeting or other covering, doors etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings [ exclusive of steel sheeting or other covering, running rails and guides ] and hanging, also fastening and fixing complete all as specified and as directed. 92 m & l for granite stone slabs of 18 to 20 mm thick of colour mexican red / ruby red / z black / pearl black as in skirting, dado, risers of steps, jambs, pillars, wall lining [ veneering to wall ] etc. with machine cut edges, table rubbed and prepolished to smooth mirror finish all to required sizes, granite stone slabs shall be of design / pattern as directed, including diagonals, inlays, borders, margins in two or more colours / shades, designs / patterns of stone slabs, set and bedded with grey cement [ slurry ] and jointed andpointed flush using polymer based cementitious tiling joint filler to match the shade of the granite slabs over backing coat of 10mm thick in cement mortar 1:3complete all as specified and as directed. note: single stone slab shall be used for entire height of skirting / dado / risers and joints shall match with the flooring. 93 s & fstainless steel kitchen sink with drainage board, made of stainless steel sheet of 1 mm thick, with plugs, washers, waste fittings, 32 mm dia, brass, chromium plated, and 32mm dia pvc flexible waste pipe, 750 mm long, including bedding in cement mortar to dwarf wall or including fixing cantilever ci brackets and connecting union to waste pipe, over all size 915 mm x 460 mm bowl size 410 mm x 330 mm x 160 mm complete all as specified and as directed. 94 s & f floor door stopper of size 150 mm of aluminium alloy body and tongue, anodised, with hard drawn steel spring complete all as specified and as directed. 95 m & l for point wiring complete with 1100 volts, frls grade, 1.5 sq.mm, single core, two runs, pvc insulated, unsheathed, multistranded copper conductor cable, conforming to is 694 drawn through and including heavy duty pvc conduit, 20 mm dia including all accessories concealed in walls / roofs / floors / ceiling etc. or surface type / semi concealed type and metal gi flush box of suitable size and thickness including modular type base / grid frame & cover frame for housing modular type switches, sockets and regulators etc. concealed in walls, including 1100 volts, frls grade, 1.5 sq.mm, single core, pvc insulated, unsheathed, multistranded copper conductor cable as earth continuity conductor with colour coding and connecting to earth dolly for one light / fan point / bell point / switchcomplete all as specified and as directed. 96 all as per serial item no. 91 above but one 3 pin switch socket outlet 5 amps on independent board complete all as specified. 97 all as per serial item no. 91 above but one 3 pin switch socket outlet 5 amps on same board complete all as specified. 98 all as per serial item no. 91 above but one 15 amps power point on independent board, with 1100 volts, frls grade, 4.0 sq.mm, single core, pvc insulated, unsheathed, multistranded copper conductor cable confirming to is 694 and including 1100 volts, frls grade, 4.0 sq.mm, single core, pvc insulated, unsheathed, multistranded copper conductor cable as earth continuity conductor. 99 s & f switch, modular type, one module, single pole, one way, 6 amps, 230 volts complete all as specified and as directed. 100 s & f switch modular type, one module, single pole, one way, 16 amps, 230 volts complete all as specified and as directed. 101 s & f ceiling rose, pvc body, 65 x 50 mm, three terminals, 230 volts complete all as specified and as directed. 102 s & f socket outlet, 3 pin, 6 amps, modular type, two modules, 230 volts, complete all as specified and as directed. 103 s & f socket outlet, 3 pin, 16 amps and 3 pin, 5 amps, modular type, two modules, multipurpose, 230 volts complete all as specified and as directed. 104 s & f bell push, modular type, single pole, 5 amps, 230 volts complete all as specified and as directed. 105 s & f bell, ding dong / multi music type, ac, 230 volts, single pole complete all as specified and as directed. 106 s & f sp & n enclosure with 2 pole and earth metal plug & socket for incorporating sp mcb complete including one mcb, sp, 20 amps, 240 volts complete all as specified and as directed. 107 s & f surface & wall mounted energy efficient led tube light fitting, of not less than 2000 lumens output, 5700 k of cool white, with extruded aluminium / crca housing and robust construction with necessary acrylic diffuser & integrated electronic driver, all accessories internally prewired and connecting up with twin core pvc insulated, sheathed flexible copper conductor cable of size 1.5 sq.mmcomplete all as specified and as directed. note: light fitting shall be of pf>0.95 108 s & fsurface & wall mounted energy efficient led decorative lamp, of not less than 1000 lumens output, 5700 k of cool white, with extruded aluminium / crca housing and robust construction with necessary acrylic diffuser & integrated electronic driver, all accessories internally prewired and connecting up with twin core pvc insulated, sheathed flexible copper conductor cable of size 1.5 sq.mm complete all as specified and as directed. note: light fitting shall be of pf>0.95 109 s & fenergy efficient sleek led mirror light fitting of not less than 500 lumens, surface & wallmounted with acrylic / pmma diffuser for soft glare free light with all accessories internally prewired and including connecting up with twin core pvc insulated, sheathed flexible copper conductor cable of size 1.5 sq.mm and complete all as specified and as directed. note: light fitting shall be of pf>0.95 110 s & f energy efficient, low noise, ceiling fan, 1200mm sweep of any colour as approved, 03 blades, bee 5 star rated, with bldc motor, copper wound, 350 rpm, with double ball bearing, conforming to is 374, isi marked, suitable for operation on single phase, 240 volts, ac, 50hz, including down rod, canopies, shackles, safety rope, hanging clamps, bushes, having p.f >0.95, service value >6.5, air delivery >215 cmm, power consumption less than 35 watt, thd less than 5%including provision of electronic speed control regulator step type, including connecting up with twin core pvc insulated, sheathed flexible copper conductor cable of size 1.5 sq.mm complete all as specified and as directed. note: ceiling fan shall be provided with 05 years onsite replacement warranty. rate quoted is deemed to be including the same and nothing shall be paid extra on this account. 111 s & f exhaust fan, 230mm sweep, 1400 rpm, metal body, heavy duty, with double ball bearing, generally conforming to is, isi marked, suitable for operation on single phase, 240 volts, ac, 50 hz, including louvers shutter / grill / guard, bee 5 star rated and of approved colour including connecting up with twin core pvc insulated, sheathed flexible copper conductor cable of size 1.5 sq.mm and fixing in existing opening and making good the disturbed surface to match with existing surfaces complete all as specified and as directed. 112 s & f energy efficient, bee 5 star rated storage type water heater [ geyser ] 25 litres capacity with 2000 watt capacity heating element conforming to is 2082, vertical storage type with specially designed titanium enamel coated / glass coated steel inner tank & heating element and abs outer shell complete fixed to wall with suitable expansion fasteners including 02 nos. of 450 mm long x 15mm dia stainless steel braided flexible hot & cold water connections and 15mm bore non return valvecomplete all as specified and as directed. note: geyser shall be provided with 05 years onsite replacement warranty. rate quote is deemed to be including the same and nothing shall be paid extra on this account. 113 s & f energy efficient & long life building security light luminaire, of not less than 4500 lumens output, 5700 k with pressure die cast aluminium housing, ip66 protection, heat resistant glass cover, high power leds as light source, electronic driver including gi bracket made out of 32 mm bore gi tube, medium grade of size not exceeding 1.50 m in length and bent to shape required and fixed with 2 nos of pole fitting clamps made out of ms flat of size 50 x 6mm, bolts, nuts, washers and painting with two coats of aluminium paint over a coat of primer red oxide zinc chrome primer and connecting up with three core pvc insulated, sheathed flexible copper conductor cable of size 1.5 sq.mmcomplete all as specified and as directed. note: light fitting shall be of pf>0.95 114 s & fmccb db v tpn, 4 way, 415 volts, with din channel, double door with 200 amps rated bus bar suitable for mounting mcbbs flush mounted with wall including making good disturbed surfaces complete all as specified and as directed. 115 s & fmcb db, spn, 12 way, 240 volts, with din channel, double door with 200 amps rated bus bar suitable for mounting mcbs flush mounted with wall including making good disturbed surfaces complete all as specified and as directed. 116 s & f mcb, spn, 40 to 63 amps, 10 ka, c curve, ac, 230 volts, 50 hz complete all as specified and as directed. 117 s & f mcb, tpn, 40 to 63 amps, 10 ka, c curve, ac, 230 volts, 50 hz complete all as specified and as directed. 118 s & f mccb, fp, 63 amps, 16 ka, 415 volts, 50 hz, suitable for fixing on n3 frame complete all as specified and as directed. 119 s & f mccb, fp, 125 amps, 16 ka, 415 volts, 50 hz, suitable for fixing on n3 frame complete all as specified and as directed. 120 s & fmcb, sp, 6 to 32 amps, 10 ka, c curve, ac, 230 volts, 50 hz complete all as specified and as directed. 121 m & l for sub main wiring with 2 runs of single core 2.5 sq.mm single core, pvc insulated, unsheathed, multistranded copper conductor cable, 1100 volts, frlsh grade, isi marked, drawing through and including heavy duty pvc conduit, 20 mm dia with all accessories concealed in walls / roofs / floors / ceiling etc. or surface type / semi concealed type including one run of 2.5 sq.mm, single core, pvc insulated, unsheathed, multistranded copper conductor cable, 1100 volts, frlsh grade earth continuity conductorcomplete all as specified and as directed. note: 3 runs of 2.5 sq.mm pvc insulated coper conductor cable& one run of 20 mm dia pvc conduit will be measured as one unit 122 m & l for sub main wiring with 2 runs of single core 4 sq.mm single core, pvc insulated, unsheathed, multistranded copper conductor cable, 1100 volts, frlsh grade, isi marked, drawing through and including heavy duty pvc conduit, 20 mm dia with all accessories concealed in walls / roofs / floors / ceiling etc. or surface type / semi concealed type including one run of 4 sq.mm, single core, pvc insulated, unsheathed, multistranded copper conductor cable, 1100 volts, frlsh grade earth continuity conductor complete all as specified and as directed. note: 3 runs of 4 sq.mm pvc insulated coper conductor cable& one run of 20 mm dia pvc conduit will be measured as one unit 123 m & l for sub main wiring with 2 runs of single core 6 sq.mm single core, pvc insulated, unsheathed, multistranded copper conductor cable, 1100 volts, frlsh grade, isi marked, drawing through and including heavy duty pvc conduit, 20 mm dia with all accessories concealed in walls / roofs / floors / ceiling etc. or surface type / semi concealed type including one run of 6 sq.mm, single core, pvc insulated, unsheathed, multistranded copper conductor cable, 1100 volts, frlsh grade earth continuity conductor including taking down old sub main wiring of any description and making good disturbed surface complete all as specified and as directed. note: 3 runs of 6 sq.mm pvc insulated coper conductor cable& one run of 20 mm dia pvc conduit will be measured as one unit 124 supplying, laying and testing xlpe insulated and pvc sheathed, frls, armoured heavy duty underground cable, isi marked with aluminium stranded conductor 1100 volt grade of size 3.5 core, 25 sq.mm cross section suitable for earthed system, laying in trenches / duct / fixed to poles / drawn through pipes / sleeving through pipe in duct, including suitable size double compression copper stainless steel cable gland, crimping type cable lugs, sockets etc. complete all as specified and as directed. 125 m & l for dry river sand cushioning over and around the cable for cable protection in trenches, levelled and punned down complete all as specified and as directed. note: the punned down thickness shall be measured for payment. 126 supply and lay bricks, common burnt clay building bricks, sub–class b, designation 75 in trenches for cable protection complete all as specified and as directed. 127 supplying and laying gi pipe, 40mm dia, light grade for cable protection at road crossing etc. or fixing on wall / poles of any type, secured with clamps complete all as specified and as directed. 128 m & l for cutting bituminous road / hardstanding etc. as required for jointing / laying cables and pipeline of width not exceeding 300mm and depth not exceeding 600mm and refilling after laying and making good with pcc 1:2:4, type b1 using 20mm graded stone aggregate, 100mm thick complete all as specified and as directed. 129 earthing complete with galvanised steel earth plate electrode 600 x 600 x 6 mm thick burried directly in ground [ earth pit not less than 2.25 m deep below ground level ] with top edge of plate not less than 1.50 m below normal ground level connected to 4 mm gi wire [ earth lead ] and gi pipe 15 mm, medium grade for earthing lead protection to the extent of maximum 7.5m, earth plate electrode surrounded by 150mm thick packed layers of charcoal and common salt filled in alternate layers, connected to the plate by means of gi bolts & nuts complete all as per electrical plate no. 3 of ssr part – i, connected to panel / db including testing on completion including main earthing, charcoal, common salt, pcc [ 1:2:4, type b1 ] pit with rcc 1:2:4, type b1 cover, 50 mm thick with 6 nos, 8 mm dia tmt bars in both ways, ms frame made with 40 x 40 x 6 mm angle iron, ms funnel with 20 mm bore, medium grade gi watering pipe, wire mesh, earth work excavation, return filling, removal of surplus soil etc.complete all as specified and as directed. 130 s & f microprocessor based single phase, 2 wire smart prepaid electronic tamper proof digital energy meter with bright lcd display, in home display unit including implementation of vending software system through server duly mapping of consumer, token system, load control facility, optical port for local communication / consumer interface unit with in built blue tooth low energy [ ble ] for remote access and alongwith vending software, high accuracy, rating 5 to 60 ampswith class 1 accuracy, ip 54 ingress protection, conforming to is 16444 & is 15959, iec 62055 31, iec 62053 21, iec 62052 11, cbip publication no. 304, isi marked, suitable for 240 volts, ac, 50 hz, including housing inmeter box with provision for earth connection, two separate cable entries for incoming and outgoing cables, transparent glass door for reading visibility with hinges and provision of 4 nos. of tamper proof lead free seals, complete all as specified and as directed. make: siemens / l & t / havells / hpl / schneider / securenote: [ a ] energy meter shall be provided with 10 years onsite replacement warranty and the rate quoted is deemed to be including the same and nothing shall be paid extra on this account. [ b ] the bidder is required to submit authenticity certificate issued by oem for the meters supplied under this contract. [ c ] meter box shall be measured for and paid separately under relevant item of boq. 131 s & f hot press moulded smc meter box of size not less than 250mm ( h ) x 250mm ( w ) x 155mm ( d ) suitable for housing of single phase prepaid electric energy meter, conforming to relevant is, with viewing glass, hinged door and earth bolt, mounted on pole / wall with suitable clamps / bolts / nuts complete all as specified and as directed.make: cat no. gsmb 2525 of sintex or equivalent in hensel / c&s 132 s & f upvc pipe of 50 mm bore, of pressure rating 10 kgf / sq.cm including all fittings such as bends, tees, short pieces, connectors, elbows, reducers, sockets etc and fixed to walls, ceiling, and laid on floors including testing complete all as specified and as directed. 133 s & f upvc pipe of 25 mm bore, of pressure rating 10 kgf / sq.cm including all fittings such as bends, tees, short pieces, connectors, elbows, reducers, sockets etc and fixed to walls, ceiling, and laid on floors including testing complete all as specified and as directed. 134 s & f gun metal globe or gate valve of class i, pressure tested of 1.5 mpa, 50 mm bore with iron wheel head, screwed both ends for iron pipe, conforming to is, isi marked complete all specified and as directed. 135 m & l for cutting or screwing existing steel tubing for alteration or additions of suitable size for 50mm dia complete all specified and as directed. 136 m & l for construction of valve chamber of size 600 x 600 x 600 mm internal size suitable for sluice valve, with pcc 1:4:8, type d2, using 40mm graded aggregate for foundation, 200 mm thick brickwork with fly ash bricks in cement mortar 1:6, 40 mm thick pcc, 1:2:4, type b1, using 20mm graded aggregate coping, rendering in cm 1:4, 15 mm thick including provision of mild steel sheet cover 3 mm thick with 40 x 40 x 6 mm size angle iron frame work embedded in concrete with suitable hinges and locking arrangements including two coat of synthetic enamel black paint over a coat of red oxide zinc chrome primer to steel surfaces and includingdemolition of existing valve chamber, necessary earth work excavation in any type of soil etc., removal of surplus soil off the premises complete all as specified and shown on drawing cedd / td / 119, sheet no. 1 / 1 dated 20 august 1983, revised up to 21 september 1992....
Due Date : September 10, 2022
Tender Value : ₹ 1.30 Crore
