37718314 bids are invited for n9515 0000 ( mild steel sheet black 2500x 1250x160mm ) ( q3 ) , n9530 000147 ( alu bronze bar rd solution heat dia 100mm ) ( q3 ) , n9535 000443 ( sheet alluminium alloy sheet 2400x900x3.55mm ) ( q3 ) mse total quantity : 18...
37434240 auction sale of lot no: 04 lot name: old aluminium alloy dummy pads...
37358604 tender for supply of flp material fl proof long description: flameproof & weatherproof switch socket combined with plug as per the specifications mentioned below. ( i ) enclosure : ex d as per is : 2148 / 81 suitable for installation in hazardous location as per the area of classification mentioned ( ii ) area classification : div / zone 1 & 2 as per is : 5572 / 94 gas group : iia &iib as per is : 2148 / 81 ( iii ) weatherproof protection : ip 65 as per is : 13947 ( part 1 ) ( iv ) rating : 16 a , 240 v ac , 1 phase , 3 pin ( v ) material : cast aluminum alloy lm6 ( vi ) gasket : endless neoprene rubber ( vii ) hardware : stainless steel ( viii ) finish : inside & outside light grey epoxy powder coating shade no. 631 as per is : 5 ( ix ) earthing : 1 no inside and 2 nos outside ( x ) cable entry : 2 nos x 3 / 4 et ( xi ) terminals : brass stud / clip on type terminals fitted on non hygroscopic insulated dmc terminal block suitable for terminating 2 nos. 3c x 2.5 sq mm ywy cable, flp & wp double compression glands.specifications: ( i ) cable gland : ex d as per is : 2148 / 81 suitable for installation in hazardous location as per the area of classification mentioned ( ii ) area classification : div / zone 1 & 2 as per is : 5572 / 94 and gas group : i, iia &iib as per is : 2148 / 81 ( iii ) weatherproof ingress protection : ip 66 as per is : 13947 ( part 1 ) or is : 2147 / 1962 ( iv ) cable gland size : 32 mm et.suitable for cable od : 27.0 30.0 mm ( v ) material : nickel coated brass., flp & wp double compression glands.specifications:i ) cable gland : ex d as per is : 2148 / 81 suitable for installation in hazardous location as per the area of classification mentioned ( ii ) area classification : div / zone 1 & 2 as per is : 5572 / 94 and gas group : i, iia &iib as per is : 2148 / 81 ( iii ) weatherproof ingress protection : ip 66 as per is : 13947 ( part 1 ) or is : 2147 / 1962 ( iv ) cable gland size : 1 1 / 2 ( 38 mm ) et. suitable for cable od : 30.5 33.5 mm ( v ) material : nickel coated brass etc...
37202417 bids are invited for indium free aluminium alloy anode mk xi nsn5342 720484379 (q3) , mg. aluminium alloy anode pkoa 8 nsn5342 720513691 (q3) mse total quantity : 605...
37196222 supply of aluminium single ladder 9.14 meter ( 30 feet with hook on top ) long without joint aluminium ladder made out of high tensile aluminium alloy c section as per is 773 / 1983 of size: 66.6 mm x 31.8 mm thickness of section 4 mm with step 25.4 mm dia. aluminium non slippery corrugated pipe at 10 center double rivited to chhannel to ensure maximum safety. steps must be strong enough to support at a time weight of 2 men ( 140 kg ) with warranty as per is 4571 / 1977 & rubber shoes to be fitted on both ends. make sumer, skyward, sj, king or similar. [ warranty period: 30 months after the date of delivery ] , aluminium single ladder 9.14 meter ( 30 feet with hook on top ) long without joint aluminium ladder made out of high tensile aluminium alloy c section as per is 773 / 1983 of size: 66.6 mm x 31.8 mm thickness of section 4 mm with step 25.4 mm dia. aluminium non slipperycorrugated pipe at 10 center double rivited to chhannel to ensure maximum safety. steps must be strong enough to support at a time weight of 2 men ( 140 kg ) with warranty as per is 4571 / 1977 & rubber shoes to be fitted on both ends. make sumer, skyward, sj, king or similar [ warranty period: 30 months after the date of delivery ] ...
36960746 supply of aluminium single ladder 9.14 meter ( 30 feet with hook on top ) long without joint aluminium ladder made out of high tensile aluminium alloy c section as per is 773 / 1983 of size: 66.6 mm x 31.8 mm thickness of section 4 mm with step 25.4 mm dia. aluminium non slippery corrugated pipe at 10 center double rivited to chhannel to ensure maximum safety. steps must be strong enough to support at a time weight of 2 men ( 140 kg ) with warranty as per is 4571 / 1977 & rubber shoes to be fitted on both ends. make sumer, skyward, sj, king or similar. [ warranty period: 30 months after the date of delivery ] , aluminium single ladder 9.14 meter ( 30 feet with hook on top ) long without joint aluminium ladder made out of high tensile aluminium alloy c section as per is 773 / 1983 of size: 66.6 mm x 31.8 mm thickness of section 4 mm with step 25.4 mm dia. aluminium non slipperycorrugated pipe at 10 center double rivited to chhannel to ensure maximum safety. steps must be strong enough to support at a time weight of 2 men ( 140 kg ) with warranty as per is 4571 / 1977 & rubber shoes to be fitted on both ends. make sumer, skyward, sj, king or similar [ warranty period: 30 months after the date of delivery ] ...
36787031 auction sale of lot no: 24.0 lot name: alum scrap alluminium alloy...
36783781 supply of aluminium single ladderaluminium single ladder, aluminium single ladder 9.14 meter ( 30 feet with hook on top ) long without joint aluminium ladder made out of high tensile aluminium alloy c section as per is 773 / 1983 of size: 66.6 mm x 31.8 mm thickness of section 4 mm with step 25.4 mm dia. aluminium non slippery corrugated pipe at 10 center double rivited to chhannel to ensure maximum safety. steps must be strong enough to support at a time weight of 2 men ( 140 kg ) with warranty as per is 4571 / 1977 & rubber shoes to be fitted on both ends. make sumer, skyward, sj, king or similar. [ warranty period: 30 months after the date of delivery ] , aluminium single ladder 9.14 meter ( 30 feet with hook on top ) long without joint aluminium ladder made out of high tensile aluminium alloy c section as per is 773 / 1983 of size: 66.6 mm x 31.8 mm thickness of section 4 mm with step 25.4 mm dia. aluminium non slipperycorrugated pipe at 10 center double rivited to chhannel to ensure maximum safety. steps must be strong enough to support at a time weight of 2 men ( 140 kg ) with warranty as per is 4571 / 1977 & rubber shoes to be fitted on both ends. make sumer, skyward, sj, king or similar [ warranty period: 30 months after the date of delivery ] ...
36427936 bids are invited for strap cutter mse strap cutter light 32 , tensioner,alloy steel,maint , sealer,aluminium alloy,maint , strap cutter heavy duty 50 total quantity : 30...
36416666 auction sale of lot no: 40 lot name: alum. scrap alluminium alloy...
36323010 bids are invited for nsn5342 720484365 indium free aluminium alloy anode mk ii ( q3 ) , nsn5342 720484364 indium free aluminium alloy anode mk iii ( q3 ) , nsn5342 720484372 indium free aluminium alloy anode mk vi ( q3 ) , nsn5342 720484379 indium free aluminium alloy anode mk xi ( q3 ) mse total quantity : 1459...
36190674 bids are invited for mn activated low potential 22v53c002 1 mn activated low potential al alloy anodes poka 3 2 indium free aluminium alloy anode mk iv 3 mn activated low potential al alloy anodes poka 1 4 indium free aluminium alloy anode mk i 5 indium free aluminium alloy anode mk v 6 mn activated low potential al alloy anodes poka 5 total quantity : 1700...
36160657 provision of essential b and r and e and m items for 308 type iii flats at ayyapakkam as per boq 2 s&f for powder coated aluminium frame for doors, windows & ventilators with one or more rebates including joining cleats for fixing etc. complete all as specified 3 s&f for powder coated aluminium windows and ventilator shutters, sliding type without sash bars of aluminium section of weighing 0.55 kg/m including necessary jointing cleats, glazing clips, neoprene rubber packing, powder coated aluminium snap beading, screws etc complete all as specified and as directed. 4 s&f stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and as directed. 5 s&f 2nd class hard wood 35 mm thick glazed and skelton shutter open rebated factory made and prepared to receive glass / gauge etc, edges of framing plain, chamfered or rounded and fitted with cut and mitered beads for securing gauge, size of members as per ssr part i section clause 8.20 (a) all as specified and as directed. 6 s&f 2nd class hard wood (sal) plain solid straight chowkhat or frame, wrought, framed, rebated on the solid, put together with glue and pinned at joint complete all as specified and as directed.. 7 m & l for preparation of new wooden surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel painting over a coat of pink primer complete all as specified and as directed. 8 s&f for 300 mm aluminium alloy, anodised, sliding door bolts with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and as directed 9 s/f 150 mm aluminium handles, cast type, anodised etc complete all as specified and as directed. 10 s&f for 300mm, mild steel ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and as directed. 11 s&f for aluminium anodised barrel tower bolt 150 mm length complete all as specified and as directed. 12 s&f for 100 mm aluminium anodized butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised complete all as specified and as directed. 13 s&f for 140mm length floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor / door complete all as specified and as directed. 14 s&f 18/19mm thick, solid core construction with block board grade 1 quality exterior garde decorative type with decorative face veneer with lipping on both faces as in kitchen cupboards including shutter, drawer etc. complete all as specified and as directed. 15 s&f for 150 mm mild steel tee hinges, stove enamelled black, medium type and fixed complete all as specified and as directed. 16 s&f for ball catches with 8mm dia steel ball, and brass body and strikingplate including letting in and fixed complete all as specified and as directed. 17 s&f for aluminium anodised barrel tower bolt 75 mm length complete all as specified and as directed. 18 s&f for drawer handles, projection drop (50mm to 65mm) on screwed plate complete all as specified and as directed. 19 s&f for 50mm dia, polished, hard wood knobs fixed with screws complete all as specified and as directed. 20 supply and fixed 600 mm x 450 mm size beveled edge mirror of selected quality glass, 5.50 mm thick, mounted on 6mm thick ac pain building board or commercial plywood and fixed to wall with wooden plugs and chromium plated brass screws & cup washers complete all as specified and as directed. 21 s&f steel plate rack made of 0.63mm thick stainless sheet of overall size 600x760x250mm with providing necessary partition shelves & hanging arrangement etc as per manufacturer trade pattern as approved by the engineer in charge and fixed to wall with wooden plug with brass chromium plated screws complete all as specified and as directed. 22 s&f for cabinet mirror of standared size (340mmx540mmx130mm) ptmt alloy inlcluding shleves and shutters topped with mirror fixed complete all as specified and as directed. 23 s&f for 20mm dia stainless steel decorative curtain rod fixing to all opening and joineries portion complete all as specified and directed. 24 m&l for stainless steel brackets (decorative type) with end holders complete all as specified and directed. 25 supply and fix in towel rail, 600mm long chromium plated fixed with and including chromium plated brass screws with wooden plugs complete all as specified and as directed 26 suuply and fixed in 15mm dia bore stop valves/ angular valve fancy type chromium plated (concealed type) screwed both ends for 15mm dia bore gi pipe or for union complete all as specified and as directed. 27 e/m schedule 28 supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 v, 1200 mm sweep. min air delivery 210 cfm with service value 6.00 bee. five star rated with brushless direct current motor (bldc) all as specified and as directed by engineer in charge. 29 supply and fix electric water heater, storage type steel body with copper inner tank and heating element upto 2 kw capacity 25 litre, bee 5 star rated complete with all accessories such as safety valve, thermostate, nrv, connection piece etc all as specified and directed by engineer in charge. 30 supply and fix exhaust fan heavy duty , steel body ac single phase. 230v of size 300m sweep with, blades, and frame andlouvers all as specified and directed by engineer in charge. 31 supply and fixing led light fitting mirror type with high out put diffuser 4 feet, 20 watt 220 v ac decorative type with driver holder and led lamp including connecting up with three core flexiblecopper conductor cable of suitable size complete all as specified and directed by engineer in charge. 32 supply and fixing led light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 v ac decorative type with driver holder and led lamp including connecting up with three core flexiblecopper conductor cable of suitable size complete all as specified and directed by engineer in charge. 33 s & f call bell ding dong, ac, 240 v, single pole, complete all specified and directed. ...
36156607 e public tender for supply of safety items at iocl atchutapuram terminal stainless steel conforming to grade 1 or 4 of is 3444:1999 ( latest amendments ) / aluminium alloy shall conform to is designation 4225, 4450 or 4600 of is 617:1976 ( latest amendments ) exposed aluminium surfaces shall an anodized finish and all threaded parts of aluminium alloy components shall be coated with molybdenum listed grease . / zinc aluminium alloy as per clause no 5.2.3 of bis 903 : 1993 ( latest amendments aluminum alloys used for casting shall conform to designation 4450, 4425 and 4600 of is :617:1975 etc ...
35806565 bids are invited for alluminium alloy sheet 22v95c012 mse 1 alluminiunm alloy sheet perforated 1000 x 2000 x 1.6 mm 2 alluminium chequered plate ( 3658 x 813mm x 5mm ) 3 allum. alloy plate size 5000x1250x5mm 4 alu.alloy angle bar 50x50x5mm l 5000mm total quantity : 373...
35488394 supply, installation, testing and commissioning of lighting protection system to sri vakulamatha temple, tirupati , supply and installation of 10mm dia aluminium alloy solid round conductor of material aimgsi used in air termination and down conductor system. cross sectional area of conductor should be 50 mm2.test parameter:a. lightning impulse current of 100 ka for 10 / 350 microsb. electrical resistivity 0.036 micro ohm, tensile strength 120 to 240 mpa or n / mm2, salt spray no sign of corrosion.tested as per iec 62561 2.cape type: src 10 al ( article no. 400 009 ) / any other equvalant reputed make, supply and installation of stainless steel conductor holder for fixing the 10 mm dia round conductor on the side wall.test parameter:salt spray test no sign of corrosiontested as per iec 62561 1cape type: ch 8 10 ( article no. 400 213 ) / any other equvalant reputed make, supply and installation of stainless steel cross connector for 8 mm solid round al. conductor and 10 mm copper coated conductor to meet the requirements for is / iec 62305. tested for electrical, mechanical and chemical as per iec 62561.cape type no. ccss 8 10 ( article no. 400 206 ) / any other equvalant reputed make, supply and installation of expansion piece with connector to compensate the expansion and contraction of solid round al. conductor during temperature variations. expansion piece should be consider at every 20 meter length of straight horizontal air termination and connected at both the end with use of straight connector conductor.test parameter:electrical resistivity test 0.036 micro ohm, salt spray test no sign of corrosion.tested as per iec 62561 1.cape type: epc 8 ( article no:401 209 ) / any other equvalant reputed make, supply and installation of straight conductor connector for interconnecting 8mm aluminium conductor to meets the requirement of is / iec 62305.tested for electrical, mechanical and chemical as per iec 62561.cape type : cj 10 / any other equvalant reputed make, supply and installation of 2 metre vertical airterminal of dia 10 mm with interception tip with supporting accessories selected as per angle of protection chart to meet the requirement of is / iec 62305. tested for electrical, mechanical and chemical as per iec 62561. cape type: vat 2 ( article no. 400 420 ) + cape type: itvat ( article no. 400 405 ) + supporting accessories / any other equvalant reputed make, down conductor:supply and installation of 10mm dia aluminium alloy solid round conductor of material aimgsi used in air termination and down conductor system. cross sectional area of conductor should be 50 mm2.test parameter:a. lightning impulse current of 100 ka for 10 / 350 sb. electrical resistivity 0.036 micro ohm, tensile strength 120 to 240 mpa or n / mm2, salt spray no sign of corrosion.tested as per iec 62561 2.cape type: src 10 al ( article no. 400 009 ) / any other equvalant reputed make, supply and installation of stainless steel conductor holder for fixing the 10 mm dia round conductor on the side wall.test parameter:salt spray test no sign of corrosiontested as per iec 62561 1cape type: ch 8 10 ( article no. 400 213 ) / any other equvalant reputed make, supply and installation of lightning counter lcd screen shows the number of lightning strikes, hour and date of lightning events buttons enable time / date setting and log viewing. replaceable battery, working life minimum five years, complies with iec / en 62561 6.cape type no: pro ler ( article no. 400 999 ) / any other equvalant reputed make, supply and installation of test joint with enclosure to interconnect between 10 mm al. round conductor to 10 mm round copper coated round conductor to meet the requirements of is / iec 62305. tested for mechanical as per iec 62561.cape type: tjrre ( article no. 401 215 ) / any other equvalant reputed make, supply and installation of rust resistant non corossive 10 mm dia copper bonded round conductor used for earth termination inside the concrete and soil.test parameter:short circuit current test for copper bonded conductor: test 6 ka ratings, as per cross sectional area for 1 sec ( is3043 or ieee80 ) electrical resistivity before and after salt mist spray test: 0.25 micro ohm max. tensile test 290 to 510 n / mm2, adhesion no peel or crack and bend test no seperation of cu, cu coating thickness min. 70 micro ohmtested as per iec 62561 2.cape type no. src 10 cu ( article no. 400 010 ) or any other equvalant, supply and installation of stainless steel cross connector for 8 mm solid round al. conductor and 10 mm copper coated conductor to meet the requirements of is / iec 62305. tested for electrical, mechanical and chemical as per iec 62561.cape type: ccss 8 10 ( article no. 400206 ) / any other equvalant, supply and installation of cape make ul listed maintenance free copper bonded earth rod of 3048 mm length having the dia of 17.2 mm with copper coating thickness of 254 microns. the rod has been tested for dimension, marking, tensile strength, salt mist, coating thickness, electgrical resistivity test before and after corrosion test as per iec 62561 2 and ul 467.cape type: cbr 1710 ( article no.: 300 060 ) / any other equvalant supply and installation of cape make earth enhancing mineral compound tested for leaching and tclp with nabl accredited lab as per iec 62561 7 25 kgcape type: prosan 12.5 ( article no: 300 830 ) / any other equvalantsupply and installation of cape make earth rod clamp made for terminating cable / flat conductor.cape type: erc1417 ss ( article no: 300 463 ) / any other equvalantsupply and installation of cape make earth chamber inspection pit made up of poly propylene material.cape type: ec 290 ( article no: 300 852 ) / any other equvalant...
35392403 auction sale of lot no: 13.0 lot name: alluminium alloy...
35179328 supply, installation, testing and commissioning of lighting protection system to sri vakulamatha temple, tirupati , supply and installation of 10mm dia aluminium alloy solid round conductor of material aimgsi used in air termination and down conductor system. cross sectional area of conductor should be 50 mm2.test parameter:a. lightning impulse current of 100 ka for 10/350 microsb. electrical resistivity 0.036 micro ohm, tensile strength 120 to 240 mpa or n/mm2, salt spray no sign of corrosion.tested as per iec 62561 2.cape type: src 10 al (article no. 400 009) / any other equvalant reputed make,supply and installation of stainless steel conductor holder for fixing the 10 mm dia round conductor on the side wall.test parameter:salt spray test no sign of corrosiontested as per iec 62561 1cape type: ch 8 10 (article no. 400 213) / any other equvalant reputed make,supply and installation of stainless steel cross connector for 8 mm solid round al. conductor and 10 mm copper coated conductor to meet the requirements for is/iec 62305. tested for electrical, mechanical and chemical as per iec 62561.cape type no. ccss 8 10 ( article no. 400 206) / any other equvalant reputed make,supply and installation of expansion piece with connector to compensate the expansion and contraction of solid round al. conductor during temperature variations. expansion piece should be consider at every 20 meter length of straight horizontal air termination and connected at both the end with use of straight connector conductor.test parameter:electrical resistivity test 0.036 micro ohm, salt spray test no sign of corrosion.tested as per iec 62561 1.cape type: epc 8 (article no:401 209) / any other equvalant reputed make,supply and installation of straight conductor connector for interconnecting 8mm aluminium conductor to meets the requirement of is/iec 62305.tested for electrical, mechanical and chemical as per iec 62561.cape type : cj 10 / any other equvalant reputed make,supply and installation of 2 metre vertical airterminal of dia 10 mm with interception tip with supporting accessories selected as per angle of protection chart to meet the requirement of is/iec 62305. tested for electrical, mechanical and chemical as per iec 62561. cape type: vat 2 (article no. 400 420) + cape type: itvat (article no. 400 405) + supporting accessories / any other equvalant reputed make,down conductor:supply and installation of 10mm dia aluminium alloy solid round conductor of material aimgsi used in air termination and down conductor system. cross sectional area of conductor should be 50 mm2.test parameter:a. lightning impulse current of 100 ka for 10/350 sb. electrical resistivity 0.036 micro ohm, tensile strength 120 to 240 mpa or n/mm2, salt spray no sign of corrosion.tested as per iec 62561 2.cape type: src 10 al (article no. 400 009) / any other equvalant reputed make,supply and installation of stainless steel conductor holder for fixing the 10 mm dia round conductor on the side wall.test parameter:salt spray test no sign of corrosiontested as per iec 62561 1cape type: ch 8 10 (article no. 400 213) / any other equvalant reputed make,supply and installation of lightning counter lcd screen shows the number of lightning strikes, hour and date of lightning events buttons enable time/date setting and log viewing. replaceable battery, working life minimum five years, complies with iec/en 62561 6.cape type no: pro ler ( article no. 400 999) / any other equvalant reputed make,supply and installation of test joint with enclosure to interconnect between 10 mm al. round conductor to 10 mm round copper coated round conductor to meet the requirements of is/iec 62305. tested for mechanical as per iec 62561.cape type: tjrre ( article no. 401 215 ) / any other equvalant reputed make,supply and installation of rust resistant non corossive 10 mm dia copper bonded round conductor used for earth termination inside the concrete and soil.test parameter:short circuit current test for copper bonded conductor: test 6 ka ratings, as per cross sectional area for 1 sec (is3043 or ieee80) electrical resistivity before and after salt mist spray test: 0.25 micro ohm max. tensile test 290 to 510 n/mm2, adhesion no peel or crack and bend test no seperation of cu, cu coating thickness min. 70 micro ohmtested as per iec 62561 2.cape type no. src 10 cu (article no. 400 010) or any other equvalant,supply and installation of stainless steel cross connector for 8 mm solid round al. conductor and 10 mm copper coated conductor to meet the requirements of is /iec 62305. tested for electrical, mechanical and chemical as per iec 62561.cape type: ccss 8 10 (article no. 400206)/any other equvalant,supply and installation of cape make ul listed maintenance free copper bonded earth rod of 3048 mm length having the dia of 17.2 mm with copper coating thickness of 254 microns. the rod has been tested for dimension, marking, tensile strength, salt mist, coating thickness, electgrical resistivity test before and after corrosion test as per iec 62561 2 and ul 467.cape type: cbr 1710 (article no.: 300 060) / any other equvalant supply and installation of cape make earth enhancing mineral compound tested for leaching and tclp with nabl accredited lab as per iec 62561 7 25 kgcape type: prosan 12.5 (article no: 300 830) / any other equvalantsupply and installation of cape make earth rod clamp made for terminating cable / flat conductor.cape type: erc1417 ss (article no: 300 463) / any other equvalantsupply and installation of cape make earth chamber inspection pit made up of poly propylene material.cape type: ec 290 (article no: 300 852) / any other equvalant...
35049956 auction sale of lot no: 22 lot name: alum. scrap alluminium alloy...
34989570 supply of aluminium alloy wall support extn ladderaluminium alloy wall support extn ladder, aluminium alloy wall support extn ladder close ht 24 feet extended ht 45 feet made of high tensile aluminium alloy c section 66 x 32 x 3.16 mm thickness of ohe 30 grade t6 temper of hindalco make steel made of no slip al. alloy corrugated flutted pipe of 28 x 3mm dia seps to be riveted at top 305mm interval extendable another locking rubber shoes at the bottom safety top hooks safety hand rails and addl ms guide pipe mixed inside the ladder at 1 mtr interval for stability of ladder => limited...
34812131 bids are invited for cricket stag aluminium alloy table tennis table , stag table tennis ball , table tennis rackets , football , football shin guards , yoga mats , batting gloves , wicket keeping gloves , medicine ball 1 kg , swiss ball , shot put 4 kg , shot put 7.26 kg , men s javelin , women s javelin , tennis racket , tennis balls , discus , knee cap , ankle cap , badminton racquets , badminton racquet grips , badminton nylon shuttles , badminton outdoor nets , cricket bats english willow , throwball , carrom board , carrom board coins , carrom board striker , carrom board powder , stop watches total quantity : 146...
34796668 supply of aluminum gauge cum level along with spirit level: export quality pie brand box type precision insulated track gauge cum level our mode: lg 2 ( i ) bg made from high tensile extruded aluminum alloy tubing. the instrument measures with precision gauge, cross levels and super elevation by the use of separate spirit level. the gauge sets automatically at 90 degrees to the rail, it is precise, rugged and convenient to use, generally and functionally to rdso latest drg. no. tm / 0108 specification no. tm 58 but superior approved by rdso and railway board with spirit level model sl 2 as per rdso latest drg.no. tm 2004, brand:1.pie 2.paul&co or benra.aluminum gauge cum level along with spirit level: export quality pie brand box type precision insulated track gauge cum level our mode: lg 2 ( i ) bg made from high tensile extruded aluminum alloy tubing. the instrument measures with precision gauge, cross levels and super elevation by the use of separate spirit level. the gauge sets automatically at 90 degrees to the rail, it is precise, rugged and convenient to use, generally and functionally to rdso latest drg. no. tm / 0108 specification no. tm 58 but superior approved by rdso and railway board with spirit level model sl 2 as per rdso latest drg.no. tm 2004, brand:1.pie 2.paul&co or benra., aluminum gauge cum level along with spirit level: export quality pie brand box type precision insulated track gauge cum level our mode: lg 2 ( i ) bg made from high tensile extruded aluminum alloy tubing. the instrument measures with precision gauge, cross levels and super elevation by the use of separate spirit level. the gauge sets automatically at 90 degrees to the rail, it is precise, rugged and convenient to use, generally and functionally to rdso latest drg. no. tm / 0108 specification no. tm 58 but superior approved by rdso and railway board with spirit level model sl 2 as per rdso latest drg.no. tm 2004, brand:1.pie 2.paul&co or benra....
34741616 bids are invited for indium free aluminium 21v53c017 1 nsn5342 720484365 indium free aluminium alloy anode mk ii 2 nsn5342 720484364 indium free aluminium alloy anode mk iii 3 nsn5342 720484372 indium free aluminium alloy anode mk vi 4 nsn5342 720484379 indium free aluminium alloy anode mk xi total quantity : 1459...
34428034 bids are invited for indium free aluminium alloy anode mk xi nsn5342 720484379 (q3) , mg. aluminium alloy anode pkoa 8 nsn5342 720513691 (q3)mse total quantity : 605...
34064820 auction sale of lot no: 7 lot name: alluminium alloy...
33993500 auction sale of lot no: scrap/tlc ogl 02/sep 22 lot name: scrap aluminium alloy scrap and copper scrap...
33882329 supply of unbranded aluminum alloy pneumatic impact wrenches, size 1 / 2 ( na ) unbranded aluminum alloy pneumatic impact wrenches, size 1 / 2 ( na ) , unbranded aluminum alloy pneumatic impact wrenches, size 1 / 2 ( na ) => limited...
33871592 bids are invited for aluminium and aluminium alloy bare foil for food packaging is:15392 ( q3 ) total quantity : 40...
33732206 auction sale of lot no: 18.0 lot name: alum. scrap alluminium alloy...
33523723 provision of deficient sailors married accommodations at certain places at visakhapatnam 1 surface dressing not exceeding 15 cm deep and getting out in soft / loose soil complete all as specified and as directed. 2 rough excavation not exceeding 1.5m deep and getting out in soft / loose soil complete all as specified and as directed. 3 excavation in trenches not exceeding 1.5m wide and not exceeding 10 sq.m on plan area and not exceeding 1.5m deep in soft / loose soil complete all as specified and as directed. 4 excavation in trenches not exceeding 1.5m wide and not exceeding 10 sq.m on plan area and depth exceeding 1.5m but not exceeding 3.0m and getting out in soft / loose soil complete all as specified and as directed. 5 removal of excavated material [ soil ] to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and as directed. 6 removal of excavated material [ soil ] to a distance exceeding 250 m but not exceeding 500m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and as directed. 7 returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25cm thick of excavated soil complete all as specified and as directed. note: a deduction of 10% shall be made from total computed volume of filling to cater in bulk irrespective of machinery used for ramming. 8 m & l for pcc 1:4:8, type d 2, using 40mm graded stone aggregate as in foundation, fillings, mass concrete, footings etc complete all as specified and as directed. 9 m & l for rcc m–30 design mix, using 20mm graded stone aggregate as in foundations including rafts, footings, foundation beams, plinth beams, bases for columns etc. complete all as specified and as directed. 10 use and removal of steel formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits [ if any ] of foundation and plinth beams and similar work, vertical or to batter for rough finished surfaces complete all as specified and as directed. 11 m & l for rcc m 30 design mix, using 20mm graded stone aggregate as in columns, pillars, piers, posts and struts etc. complete all as specified and as directed. 12 use and removal of steel formwork to sides of pillars, posts, struts, piers, columns and stanchions of any shape / cross section for rough finished surfaces of concrete complete all as specified and as directed. 13 m & l for rcc m 30 design mix, using 20mm graded stone aggregate as in beams, cantilevers, bressummers, lintels over 1.5m span etc complete all as specified and as directed. 14 use and removal of steel formwork to sides and soffits of floor or roof beams, beam launchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc, splays between floors and beams and similar works for rough finished surfaces of concrete complete all as specified and as directed. 15 m & l for rcc m 30 design mix, using 20mm graded stone aggregate as in slabs supported on walls, beams, columns, landings, shelves and the like complete all as specified and as directed. 16 use and removal of steel formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work not exceeding 200mm thick [ horizontal or sloping ] including rough finished surfaces complete all as specified and directed. 17 s & f reinforcement using high strength corrosion resistant deformed tmt bars of grade fe–500d of 10mm dia and over, cut to length, bent to shape required including cranking, bending, spirally for hooping, hooking ends and binding with annealed mild steel wire not less than 0.9mm dia or securing with clips or welded complete all as specified and as directed. 18 s & f reinforcement using high strength corrosion resistant deformed tmt bars of grade fe–500d of 5mm to 10mm dia bars as in stirrups, spacers and binders, cut to length, bent to shape required including cranking, bending, spirally for hooping, hooking ends and binding with annealed mild steel wire not less than 0.9mm dia or securing with clips or welded complete all as specified and as directed. 19 s & f gi wire cloth / mesh with2 mm dia of wire and fixed with tinned tacks or stainless steel wire staples as in lateral reinforcement for pre fabricated concrete wall panels / modules all as per manufacturers instructions, as specified and as directed. 20 m & l for providing pre fabricated reinforced concrete wall panels / modules with hollow infill patterns, light weight with acoustic properties duly factory fabricated through computer aided automated 3d printing technology with desired models / patterns / logos, etc. as per the drawings provided by the engineer in charge for the building. the pre fabricated 3d wall panels shall be cast off site in layer by layer with layer thickness of 15 20mm each and layer width of 30 35mm, including transportation from off site to on site, installed and assembled in position all as per manufacturers instructions, as specified and as directed.notes: [ a ] the pre fabricated reinforced concrete wall panels / modules with any sort of design as per the drawings provided shall be procured and installed through specialist firms viz. m / s. micob pvt ltd., ( gandhi nagar, gujrat ) / m / s. tvasta manufacturer solutions pvt ltd. ( chennai ) . necessary mou shall be entered with any of the specialist manufacturer as mentioned above to provide technical support and to provide trained persons for supervision of the work and the same shall be submitted alongwith the tender documents [ t bids ] . if any tenderer fails to produce mou, their bid shall be rejected and their financial bid shall not be opened. [ b ] an authorised person of the specialist manufacturer of the panels shall be made available by the contractor at site for co ordination with the department as well as with the off site manufacturing unit for smooth execution of the work including supervision of work at site at every stage of work without hampering the desired progress of the work. [ c ] the size and shape of the panels shall vary according to the site requirement during execution of the work and the contractor shall be required to quote the rate accordingly and nothing extra shall be allowed on this account. [ d ] the contractor shall submit necessary design details and requisite manufacturers test certificates in respect of the 3d printed wall panels / modules prior to incorporation of the same at site. 21 [ e ] the fabrication of concrete 3d printed wall panels shall be commenced only after conforming the strength parameters of the walls with respect to m 30 design mix strength. the composition of materials for 3d printed walls shall be as follows: ( i ) opc 53 grade cement ( not less than 550 kg / cum ) ( ii ) fly ash ( not less than 300 kg / cum ) ( iii ) quartz m sand ( not less than 1000 kg / cum ) ( iv ) silica fumes / fibers to improve the buildability, extrudability and flowability ( not less than 180 kg / cum ) ( v ) water ( not less than 300 litres / cum ) ( vi ) super plasticizers viscosity modifying agent ( not less than 35 litres / cum ) ( vii ) galvanised steel wire mesh with 2mm dia wires as in lateral reinforcement placed in horizontal position at every 300mm height to increase tensile and flexural strength. ( viii ) fe 500d anti corrosive tmt reinforcement bars shall be used as main reinforcement with 30mm nominal cover in semi automatic method of 3d printing without hampering the printing speed. [ spacing of bars shall be as per the detailed drawing provided at the time of execution ] [ f ] all safety measures shall be ensured while transportingthe wall panels from off site to on site and the wall panels shall be transported only after attaining the target mean strength in accordance with m 30 design criteria. [ g ] each wall panel shall be provided with suitable anchorage for lifting and installing in position. suitable capacity of crane, trailer, lifting arrangements shall be provided by the contractor for handling of the panels at both off site and on site. [ h ] the weight of each panel / module shall not exceed 700 kg. [ i ] the wall panels shall be with 40% rustic finish. 22 [ j ] the panels shall be compatible to mechanical, electrical and plumbing systems to be accommodated in the building and accordingly the panels shall be fabricated in the factory as per the drawings provided or as directed by the engineer in charge as per site requirement. [ k ] the tmt bars provided as main reinforcement and wire mesh provided as lateral reinforcement shall be measured and paid separately under relevant items of this schedule / boq. [ l ] the contractor shall submit psmb duly marked with the location for record. [ m ] site visit to the manufacturer’s workshop / factory shall be made by the departmental executive staff authorized by the accepting officer during fabrication of wall panels and at the time of delivery of each lot to check the manufacturing process and to determine the strength parameters of the panels. [ n ] quality assurance plan shall be submitted by the contractor to the accepting officer for approval within 15 days from the date of commencement. 23 [ o ] the contractor shall furnish a written guarantee to ge from the specialist firm engaged by him for a period of 25 years from the certified date of completion by the ge for the effectiveness of the 3d printed wall panels supplied and installed in the subject work on non judicial stamp paper of ? 100.00. during the aforesaid guarantee period of 25 years, the contractor shall be solely responsible for the effectiveness of the 3d printed wall panels. any sign of cracks or defects of any type noticed by the ge during this period shall be promptly rectified by the contractor without any extra cost to the government. the above provision shall not however, absolve the contractor of his responsibility of effectiveness of the 3d printed wall panels as required under the provisions of contract. should the ge, at any time during construction or reconstruction or prior to the expiration of guarantee period of 25 years after the 3d printed wall panel work has been completed as per contract, finds that any building / structure showing any sign of cracks or defects of any type, the contractor shall, on demand in writing from the ge specifying the location complained of notwithstanding that the same may have been inadvertently passed / certified and paid for, forthwith undertake to carry out such treatment as may be necessary to render the structure [ s ] free from cracks or defects at his own expenses for a period of 25 years from the certified date of completion. in the event of his failing to do so, within the period as specified by the ge in his demand aforesaid, the ge may undertake such rectifications as may be necessary through other agency at the risk and expense in all respects of the contractor. the liability of the contractor under this condition shall not extend beyond the period of 25 years from the certified date of completion, unless the ge had previously given notice to the contractor. 24 [ p ] a security deposit against the guarantee period for effectiveness of the 3d printed wall panels supplied and installed in the subject work for 25 years shall be calculated @ 5% of the amount of 3d printed wall panels priced at contract rates and shall be retained by the government from the contractor’s dues. this amount shall be refunded to the contractor after the expiration of the guarantee period of 25 years from the certified date of completion by the ge, provided always that the contractor shall first have been paid the final bill and have rendered no demand certificate [ iafa – 451 ] . alternatively, the contractor may furnish fixed deposit receipt in lieu of security deposit from a schedule bank in favour of ge for the above said guarantee period. condition 10, 46 & 68 of general conditions of contracts [ iafw – 2249 ] shall be deemed to be amended to the extent mentioned above. [ q ] any minor constructional details not specified elsewhere but which are essential for execution and completion of work including all incidental charges shall also be deemed to be considered by the contractor and the rate quoted shall be deemed to include for all the above provisions no extra claims shall be allowed by the department. 25 m & l for 40 mm thick pcc 1:2:4, type b 0, using 12.5mm graded aggregate as in padding over roof slabs, surface finished fair and even without using extra cement complete all as specified and as directed. 26 m & l for preparing the surfaces of concrete roof and brushing neat cement slurry with 3.0 kg of cement per sq.m area, rendering 10mm thickin cement mortar 1:3 on concrete surfaces finished even and smooth without using extra cementincluding mixing of water proofing compound of approved make as per manufacturers instructions for levelling the surface smooth to receive the water proofing membrane, priming the surface with a coat of cold applied bituminous primer @ 0.50 kg per sq.m, applying a coat of blown bitumen of grade 85 / 25 @ 1.2 kg per sq.m, laying polymeric water proofing membrane of weight not less than 3.00 kg per sq.m reinforced with polyester non woven fabric of weight notless than 150 grams per sq.m, by torch application with side over lap of 100mm & end over lap of 150mm & tucked into the chases on vertical surfaces by thermo fusion including applying a coat of blown bitumen of grade 85 / 25 @ 1.2 kg per sq.m and finished with a coat of bituminous aluminium paint @ 100 grams per sq.m on top for water proofing treatment completecomplete all as specified and as directed. note: water proofing compound will be measured and paid separately. 27 m & l for rendering to brick / concrete surfaces, 10 mm thick in cement mortar 1:6, surfaces finished even and smooth without using extra cement complete all as specified and as directed. 28 m & l for rendering 5mm thick in cement mortar 1:4 including mixing water proofing compound as per manufacurers instructions over a backing coat of 10mm thick in cm 1:6 on concrete or brick masonry surfacesand finishing the top surface even and smooth without using extra cement complete all as specified and as directed.note: water proofing compoundwill be measured and paid separately. 29 supply only integral water proofing compound [ isi marked ] of approved make. 30 m & l for rendering 5 mm thick in cement mortar 1:3 on fair faces of concrete surface of ceiling surfaces finished even and smooth without using extra cement complete all as specified and as directed. 31 demolition of cement concrete of any description and in any position not otherwise specifically provided for and removing rubbish to a distance not exceeding 1.50 km complete all as specified and as directed. 32 m & l for two coats of weather proof exterior emulsion paint [ 100% acrylic ] by using auto roller / airless sprayer over a coat of exterior primer of same manufacturer as that of paint on newly plastered walls / ceiling, pillasters, bands, borders, soffits of chajjas and projections including necessary preparation of surfaces by using vaccume based sanding machine complete all as specified and as directed. 33 m & l for preparing newly plastered ceiling surfaces and applying threecoats of white washing complete all as specified and as directed. 34 m & l for preparing newly plastered wall surfaces by using vaccume based sanding machineandapplying two coats of acrylic washable distemper by using auto roller / airless sprayer, over a coat of alkali resistant primer over two or more coats of cement based wall care putty on walls by using multipurpose mixture for proper mixing of putty and putty sprayer for application of putty including rubbing with sand paper to obtain a smooth surface and making good any undulations on the wall surfaces complete all as specified and as directed. 35 m & l for vitrified tiles, double charged, coloured, premium quality, of size not exceeding 0.36 sq.m, 10 mm thick as in floors, set and jointed in cement slurry and pointed flush using polymer based cementitious tiling joint filler to match the shade of the tile including screed bed or bedding layer of mortar 15 mm thick in cement mortar 1:4 complete all as specified and as directed. note: the colour / shade / design of tiles shall be as approved by ge. 36 m & l for vitrified tiles, double charged, coloured, premium quality, of size not exceeding 0.36 sq.m, 10 mm thick as in skirting and dado, set and jointed in cement slurry and pointed flush using polymer based cementitious tiling joint filler to match the shade of the tile over backing coat of 10mm thick in cement mortar 1:3 complete all as specified and as directed. note: the colour / shade / design of tiles shall be as approved by ge. 37 m & l for non skid ceramic tiles, joint free, coloured, premium quality of size exceeding 0.11 sq.m and not exceeding 0.18 sq.m, 7 to 8 mm thick [ square or rectangular ] as in floors etc, set and jointed in neat cement slurry and pointed flush using polymer based cementitious tiling joint filler to match the shade of the tile including screed bed or bedding layer of mortar 15 mm thick in cement mortar 1:4 complete all as specified and as directed. note: the colour / shade / design of tiles shall be as approved by ge. 38 m & l for joint free glazed ceramic tiles, edge cut, concept type, coloured, premium quality, of size 450 mm x 300 mm, 7 to 8 mm thick as in vertical surfaces such as skirting, dado etc set and jointed in neat cement slurry and pointed flush using polymer based cementitious tiling joint filler to match the shade of the tile over backing coat of 10mm thick in cement mortar 1:3 complete all as specified and as directed. note: the colour / shade / design of tiles shall be as approved by ge. 39 s & f gi water tubing of 15 mm bore, medium grade conforming to is 1239 [ part 1 ] including all fittings such as bends, tees, short pieces, connectors, elbows, reducers, union, sockets etc fixed to walls, ceiling or laid on floors including testing complete all as specified and as directed. 40 s & f gi water tubing of 20 mm bore, medium grade conforming to is 1239 [ part 1 ] including all fittings such as bends, tees, short pieces, connectors, elbows, reducers, union, sockets etc fixed to walls, ceiling or laid on floors including testing complete all as specified and as directed. 41 s & f gi water tubing of 25 mm bore, medium grade conforming to is 1239 [ part 1 ] including all fittings such as bends, tees, short pieces, connectors, elbows, reducers, union, sockets etc fixed to walls, ceiling or laid on floors including testing complete all as specified and as directed. 42 s & fvitreous china wash down water closet [ pedestal pattern ] , white, including 10 litres capacity, pvc valve less, syphonic action type, low level flushing cistern, white, with inlet ball valve, float, handle, flush pipe of polyethylene of lowor high density of pvc, 32mm dia, pvc connection of 15mm bore and 600mm long with ptmtcheck nut and union etc. including brackets and connections to pipe and flush pipe including plastic water closet seat back closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging device and p or s trap complete all as specified and as directed. 43 s & fvitreous china ware wash hand basin, white, flat back of size 450 mm x 300 mm including pillar taps, cast copper alloy, chromium plated, fancy type, 15 mm dia, with capstan head, screwed down high pressure with or with out lettered hot or cold with long screwed shanks and fly nuts screwed for iron pipe and fixed, 32mm dia brass chromium plated waste fittings with long screw shanks and fly nuts, flange end bedded in red led cement and other end fixed, rubber plug with rings including ci brackets, cutting for and pinning in ends of brackets or erecting strand, 32mm bore pvc flexible waste pipe, pvc connection of 15mm bore and 600mm long with ptmt check nut and union etc. complete all as specified and as directed. 44 s & fbib taps, 15 mm dia, brass chromium plated, fancy type with crutch or butterfly handle, screwed down for iron pipe and fixed etc. complete all as specified and as directed. 45 s & fstop valves, 15 mm dia, cast copper alloy with capstan head, chromium plated, fancy type, screwed down high pressure with crutch or butterfly handle with long shank and cup [ concealed type ] for iron pipe etc complete all as specified and as directed. 46 s & fangle cock, 15 mm dia, cast copper alloy with capstan head, chromium plated, screwed down high pressure with crutch or butterfly handle for iron pipe etc. complete complete all as specified and as directed. 47 s & f ptmt tubular towel rail, 20mm dia, d type, 600 mm long between flanges, fixed with and including chromium plated brass screws and wooden / plastic cleats [ minimum weight 190 grams ] complete all as specified and as directed. 48 s & f ptmt soap dish with screws complete all as specified and as directed. 49 s & f rotational moulded polythene [ hdpe ] water tanks, triple layered, isi marked, cylindrical & vertical type 1000 litres capacity hoisted and fixed in position including provision of 40mm / 25mm dia spouts for connecting inlet, outlet, over flow and washout pipes complete all as specified and as directed. 50 s & f ball valves, 25 mm bore, high pressure of ptmt with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe [ minimum weight 25mm 455 grams ] etc complete all as specified and as directed. 51 s & f gun metal globe or gate valve of class i, pressure tested of 1.5 mpa, 25 mm bore with iron wheel head, screwed both ends for iron pipe, conforming to is, isi marked complete all specified and as directed. 52 m & l for 40mm bore dia high density polyethylene pipes [ hdpe of pressure rating 6 kgf / sq.cm laid in trenches or fixed to walls or ceilings or in floors etc. complete all as specified 53 s & f 75mm bore pvc [ swr ] pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and as directed. 54 s & f 75mm outlet pvc [ swr ] floor trap with grating including jointing with solvent cement complete all as specified and as directed. 55 s & f 110mm bore pvc [ swr ] pipes single socketed, in any length with rubber ring joints, fixed to walls including necessary brackets, clamps complete all as specified and as directed. 56 s & f 75 mm bore pvc [ swr ] bends of any radius including jointing with solvent cement complete all as specified and as directed. 57 s & f 110 mm bore pvc [ swr ] bends of any radius including jointing with solvent cement complete all as specified and as directed. 58 s & f 75 mm bore pvc [ swr ] branch piece, single [ singley ] equal or unequal jointing with solvent cement complete all as specified and as directed. 59 s & f 110 mm bore pvc [ swr ] branch piece, single [ singley ] equal or unequal jointing with solvent cement complete all as specified and as directed. 60 s & f 110mm bore pvc [ swr ] gully trap with grating including jointing with solvent cement complete all as specified and as directed. 61 m & l for hardcore of gauge not exceeding 63mm of broken stones or boulders, deposited, spread and levelled in layers not exceeding15 cm thick watered and rolled with power road roller of 8 to 12 ton capacity and consolidated to required gradient and camber complete all as specified. 62 m & l for 75 mm thick, pcc 1:3:6, type c 1, using 20mm graded stone aggregate as in plinth protection, surfaces finished even and smooth complete all as specified and as directed. 63 s & f solid pvc door frame of size 50mmx47mm made out of 5mm plain colour pvc sheet reinforced with ms square tube in opening complete all as specified and as directed. 64 s & f factory made solid panel pvc door shutter 30 mm thick [ style ] consisting of frame made out of m.s. tubes for top & bottom rails. m.s. frame shall be covered with heat moulded plain colour pvc c channel having a pvc sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour pvc sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour pvc sheet to be fitted in the m.s. frame welded / sealed to the stiles & rails with suitable pvc sheet beading, and joined together with solvent cement fixing in frame at site as per specification complete all as specified and as directed. 65 m & l forpowder coated aluminium sections [ minimum 50 micron thick ] of approved colour as in door, window, ventilator frames, partitions with one or more rebates and door, windows shutters sliding / openable type / ventilator shutter aluminium section including necessary joining cleats, glazing clips, neoprene rubber packing, powder coated aluminium snap beading, screws and locking arrangements complete all as specified and as directed. note: [ a ] the size of aluminium sections shall be all as specified in relevant is code and mes schedule part i. [ b ] supply only panel inserts of glass / gauze / grills will be measured and paid separately. [ c ] unit rate quoted shall be deemed to include for cost of rubber beading, glazing clips, neoprene packing and fixing only of panel inserts ofglass / gauze / grills etc. 66 s & f 75mm size, butt hinges, stainless steel, medium weight, bright polished including fixtures complete all as specified and as directed. 67 s & f aluminium anodised handle, of extruded section fabricated type of size 75mm long complete all as specified and as directed. 68 s & f aluminium anodised barrel tower bolt of size 100 mm size of extruded section complete all as specified and as directed. 69 supply only powder coated aluminium deco grill of model / design no. dg 104 ( 7.2mmx4.2mm ) including powder coated aluminium channel of size 30 x 12 x 1.5mm for fixing deco grill complete all as specified and as directed. 70 supply only 5mm thick sheet glass ordinary quality in squares exceeding 0.5 sq.m in each pane complete all as specified and as directed. 71 supply only 4mm thick figured glass and glazing with oil putty or with wooden beads in squares not exceeding 0.5 sq.m in each pane complete all as specified and as directed. 72 supply onlystainless steel wire cloth / mesh with average aperture not exceeding 1.40 mm and dia of wire 0.36 mm complete all as specified and as directed. 73 s & f stainless steel wire cloth / mesh with average aperture not exceeding 1.40 mm and dia of wire 0.36 mm complete all as specified and as directed. 74 m & l for plain cement concrete type c1 [ nominal mix ] 1:3:6 using 20mm graded stone aggregate cast in situ in lintels up to 1.5m span, cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings up to 60 cm in height, copings, kneelers, apex stones, bed plates including weathering, slightly rounded or chamfered angles and throating as directed including use and waste of form work, complete all as specified and as directed. 75 m & l for two coats of synthetic enamel paint over one coat of pink primer to newly untreated wooden surfaces over 10cm width or girth including preparation of surfaces complete all as specified and as directed. 76 s & f mild steel work conforming to fe 290, grade e 165 as in bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required, hooks [ stay ] , heavy, for large gates, hook and pintle hinges, large hasps and staples, chains, hand made sliding bolts, clamps, hold fasts, wall ties, hooks for hanging fans, plain angle cleats for securing purlins to wood trusses or rafters, knee piece inserts, two way and three way straps, plate washers and similar small articles complete all as specified and as directed. 77 s & fstainless steel curtain rod, 20 mm dia with fixing brackets, end caps etc complete all as specified and as directed. 78 s & f second class hard wood, plain, solid, straight chowkats and frames, wrought, framed, rebated on the solid, rounded or chamfered, put together with glue, pinned at joints complete all as specified and directed. 79 s & f factory made, 30 mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and as directed. 80 s & f factory made, 30mm thick, second class hard wood, glazed and skeleton door shutters, open rebated and prepared to receive glass, gauze, etc. [ without sash bars ] , edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc., sizes of members of shutters as specified in ssr part – i, section 8, clause 8.24 [ a ] and fitted to chowkats complete all as specified and as directed. 81 s & f aluminium alloy anodised sliding door bolt with hasp and staple [ bolt type ] of size 250 mm and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and as directed. 82 s & f aluminium anodised barrel tower bolt of size 300 mm size of extruded section complete all as specified and as directed. 83 s & f aluminium anodised handle, of extruded section fabricated type of size 200mm long complete all as specified and as directed. 84 m & l for two coats of synthetic enamel paint over one coat of red oxide / zinc chrome primer on new steel surfaces over 10cm width or girth including preparation of surfaces complete all as specified and as directed. 85 m & l for providing pre construction anti termite treatment for the backfill in contact with foundation by applying emulsion at the rate of 7.5 litres per square metre of vertical surface [ area of the substructure in contact with back fill ] complete all as specified and as directed. 86 m & l for providing pre construction anti termite treatment for the top surface of filled earth by applying emulsion at the rate of 5 litres per square metre ofsurface complete all as specified and as directed. 87 m & l for providing pre construction anti termite treatment for the soil under plinth protection by applying emulsion at the rate of 5 litres per square metre of surfacearea complete all as specified and as directed. 88 m & l for providing pre construction anti termite treatment for the soil along with external perimeter of building by applying emulsion at the rate of 2.25 litres per running metre of the perimeter wall complete all as specified and as directed. 89 m & l for 150 mm dia rcc pipes, class np3, laid and jointed with collars laid in trenches and jointedwith cement mortar complete all as specified and as directed. 90 m & l for concrete bed to drain pipes of size 150 mm bore packing under and haunching against the sides of pipes after they are laid and fitted in cement concrete, type c2, 1:3:6, using 40mm graded stone aggregate complete all as specified and as directed. 91 s & f rolled mild steel work conforming to fe 410 w, grade e 250, quality a as in framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc complete, drilled for fixing of steel sheeting or other covering, doors etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings [ exclusive of steel sheeting or other covering, running rails and guides ] and hanging, also fastening and fixing complete all as specified and as directed. 92 m & l for granite stone slabs of 18 to 20 mm thick of colour mexican red / ruby red / z black / pearl black as in skirting, dado, risers of steps, jambs, pillars, wall lining [ veneering to wall ] etc. with machine cut edges, table rubbed and prepolished to smooth mirror finish all to required sizes, granite stone slabs shall be of design / pattern as directed, including diagonals, inlays, borders, margins in two or more colours / shades, designs / patterns of stone slabs, set and bedded with grey cement [ slurry ] and jointed andpointed flush using polymer based cementitious tiling joint filler to match the shade of the granite slabs over backing coat of 10mm thick in cement mortar 1:3complete all as specified and as directed. note: single stone slab shall be used for entire height of skirting / dado / risers and joints shall match with the flooring. 93 s & fstainless steel kitchen sink with drainage board, made of stainless steel sheet of 1 mm thick, with plugs, washers, waste fittings, 32 mm dia, brass, chromium plated, and 32mm dia pvc flexible waste pipe, 750 mm long, including bedding in cement mortar to dwarf wall or including fixing cantilever ci brackets and connecting union to waste pipe, over all size 915 mm x 460 mm bowl size 410 mm x 330 mm x 160 mm complete all as specified and as directed. 94 s & f floor door stopper of size 150 mm of aluminium alloy body and tongue, anodised, with hard drawn steel spring complete all as specified and as directed. 95 m & l for point wiring complete with 1100 volts, frls grade, 1.5 sq.mm, single core, two runs, pvc insulated, unsheathed, multistranded copper conductor cable, conforming to is 694 drawn through and including heavy duty pvc conduit, 20 mm dia including all accessories concealed in walls / roofs / floors / ceiling etc. or surface type / semi concealed type and metal gi flush box of suitable size and thickness including modular type base / grid frame & cover frame for housing modular type switches, sockets and regulators etc. concealed in walls, including 1100 volts, frls grade, 1.5 sq.mm, single core, pvc insulated, unsheathed, multistranded copper conductor cable as earth continuity conductor with colour coding and connecting to earth dolly for one light / fan point / bell point / switchcomplete all as specified and as directed. 96 all as per serial item no. 91 above but one 3 pin switch socket outlet 5 amps on independent board complete all as specified. 97 all as per serial item no. 91 above but one 3 pin switch socket outlet 5 amps on same board complete all as specified. 98 all as per serial item no. 91 above but one 15 amps power point on independent board, with 1100 volts, frls grade, 4.0 sq.mm, single core, pvc insulated, unsheathed, multistranded copper conductor cable confirming to is 694 and including 1100 volts, frls grade, 4.0 sq.mm, single core, pvc insulated, unsheathed, multistranded copper conductor cable as earth continuity conductor. 99 s & f switch, modular type, one module, single pole, one way, 6 amps, 230 volts complete all as specified and as directed. 100 s & f switch modular type, one module, single pole, one way, 16 amps, 230 volts complete all as specified and as directed. 101 s & f ceiling rose, pvc body, 65 x 50 mm, three terminals, 230 volts complete all as specified and as directed. 102 s & f socket outlet, 3 pin, 6 amps, modular type, two modules, 230 volts, complete all as specified and as directed. 103 s & f socket outlet, 3 pin, 16 amps and 3 pin, 5 amps, modular type, two modules, multipurpose, 230 volts complete all as specified and as directed. 104 s & f bell push, modular type, single pole, 5 amps, 230 volts complete all as specified and as directed. 105 s & f bell, ding dong / multi music type, ac, 230 volts, single pole complete all as specified and as directed. 106 s & f sp & n enclosure with 2 pole and earth metal plug & socket for incorporating sp mcb complete including one mcb, sp, 20 amps, 240 volts complete all as specified and as directed. 107 s & f surface & wall mounted energy efficient led tube light fitting, of not less than 2000 lumens output, 5700 k of cool white, with extruded aluminium / crca housing and robust construction with necessary acrylic diffuser & integrated electronic driver, all accessories internally prewired and connecting up with twin core pvc insulated, sheathed flexible copper conductor cable of size 1.5 sq.mmcomplete all as specified and as directed. note: light fitting shall be of pf>0.95 108 s & fsurface & wall mounted energy efficient led decorative lamp, of not less than 1000 lumens output, 5700 k of cool white, with extruded aluminium / crca housing and robust construction with necessary acrylic diffuser & integrated electronic driver, all accessories internally prewired and connecting up with twin core pvc insulated, sheathed flexible copper conductor cable of size 1.5 sq.mm complete all as specified and as directed. note: light fitting shall be of pf>0.95 109 s & fenergy efficient sleek led mirror light fitting of not less than 500 lumens, surface & wallmounted with acrylic / pmma diffuser for soft glare free light with all accessories internally prewired and including connecting up with twin core pvc insulated, sheathed flexible copper conductor cable of size 1.5 sq.mm and complete all as specified and as directed. note: light fitting shall be of pf>0.95 110 s & f energy efficient, low noise, ceiling fan, 1200mm sweep of any colour as approved, 03 blades, bee 5 star rated, with bldc motor, copper wound, 350 rpm, with double ball bearing, conforming to is 374, isi marked, suitable for operation on single phase, 240 volts, ac, 50hz, including down rod, canopies, shackles, safety rope, hanging clamps, bushes, having p.f >0.95, service value >6.5, air delivery >215 cmm, power consumption less than 35 watt, thd less than 5%including provision of electronic speed control regulator step type, including connecting up with twin core pvc insulated, sheathed flexible copper conductor cable of size 1.5 sq.mm complete all as specified and as directed. note: ceiling fan shall be provided with 05 years onsite replacement warranty. rate quoted is deemed to be including the same and nothing shall be paid extra on this account. 111 s & f exhaust fan, 230mm sweep, 1400 rpm, metal body, heavy duty, with double ball bearing, generally conforming to is, isi marked, suitable for operation on single phase, 240 volts, ac, 50 hz, including louvers shutter / grill / guard, bee 5 star rated and of approved colour including connecting up with twin core pvc insulated, sheathed flexible copper conductor cable of size 1.5 sq.mm and fixing in existing opening and making good the disturbed surface to match with existing surfaces complete all as specified and as directed. 112 s & f energy efficient, bee 5 star rated storage type water heater [ geyser ] 25 litres capacity with 2000 watt capacity heating element conforming to is 2082, vertical storage type with specially designed titanium enamel coated / glass coated steel inner tank & heating element and abs outer shell complete fixed to wall with suitable expansion fasteners including 02 nos. of 450 mm long x 15mm dia stainless steel braided flexible hot & cold water connections and 15mm bore non return valvecomplete all as specified and as directed. note: geyser shall be provided with 05 years onsite replacement warranty. rate quote is deemed to be including the same and nothing shall be paid extra on this account. 113 s & f energy efficient & long life building security light luminaire, of not less than 4500 lumens output, 5700 k with pressure die cast aluminium housing, ip66 protection, heat resistant glass cover, high power leds as light source, electronic driver including gi bracket made out of 32 mm bore gi tube, medium grade of size not exceeding 1.50 m in length and bent to shape required and fixed with 2 nos of pole fitting clamps made out of ms flat of size 50 x 6mm, bolts, nuts, washers and painting with two coats of aluminium paint over a coat of primer red oxide zinc chrome primer and connecting up with three core pvc insulated, sheathed flexible copper conductor cable of size 1.5 sq.mmcomplete all as specified and as directed. note: light fitting shall be of pf>0.95 114 s & fmccb db v tpn, 4 way, 415 volts, with din channel, double door with 200 amps rated bus bar suitable for mounting mcbbs flush mounted with wall including making good disturbed surfaces complete all as specified and as directed. 115 s & fmcb db, spn, 12 way, 240 volts, with din channel, double door with 200 amps rated bus bar suitable for mounting mcbs flush mounted with wall including making good disturbed surfaces complete all as specified and as directed. 116 s & f mcb, spn, 40 to 63 amps, 10 ka, c curve, ac, 230 volts, 50 hz complete all as specified and as directed. 117 s & f mcb, tpn, 40 to 63 amps, 10 ka, c curve, ac, 230 volts, 50 hz complete all as specified and as directed. 118 s & f mccb, fp, 63 amps, 16 ka, 415 volts, 50 hz, suitable for fixing on n3 frame complete all as specified and as directed. 119 s & f mccb, fp, 125 amps, 16 ka, 415 volts, 50 hz, suitable for fixing on n3 frame complete all as specified and as directed. 120 s & fmcb, sp, 6 to 32 amps, 10 ka, c curve, ac, 230 volts, 50 hz complete all as specified and as directed. 121 m & l for sub main wiring with 2 runs of single core 2.5 sq.mm single core, pvc insulated, unsheathed, multistranded copper conductor cable, 1100 volts, frlsh grade, isi marked, drawing through and including heavy duty pvc conduit, 20 mm dia with all accessories concealed in walls / roofs / floors / ceiling etc. or surface type / semi concealed type including one run of 2.5 sq.mm, single core, pvc insulated, unsheathed, multistranded copper conductor cable, 1100 volts, frlsh grade earth continuity conductorcomplete all as specified and as directed. note: 3 runs of 2.5 sq.mm pvc insulated coper conductor cable& one run of 20 mm dia pvc conduit will be measured as one unit 122 m & l for sub main wiring with 2 runs of single core 4 sq.mm single core, pvc insulated, unsheathed, multistranded copper conductor cable, 1100 volts, frlsh grade, isi marked, drawing through and including heavy duty pvc conduit, 20 mm dia with all accessories concealed in walls / roofs / floors / ceiling etc. or surface type / semi concealed type including one run of 4 sq.mm, single core, pvc insulated, unsheathed, multistranded copper conductor cable, 1100 volts, frlsh grade earth continuity conductor complete all as specified and as directed. note: 3 runs of 4 sq.mm pvc insulated coper conductor cable& one run of 20 mm dia pvc conduit will be measured as one unit 123 m & l for sub main wiring with 2 runs of single core 6 sq.mm single core, pvc insulated, unsheathed, multistranded copper conductor cable, 1100 volts, frlsh grade, isi marked, drawing through and including heavy duty pvc conduit, 20 mm dia with all accessories concealed in walls / roofs / floors / ceiling etc. or surface type / semi concealed type including one run of 6 sq.mm, single core, pvc insulated, unsheathed, multistranded copper conductor cable, 1100 volts, frlsh grade earth continuity conductor including taking down old sub main wiring of any description and making good disturbed surface complete all as specified and as directed. note: 3 runs of 6 sq.mm pvc insulated coper conductor cable& one run of 20 mm dia pvc conduit will be measured as one unit 124 supplying, laying and testing xlpe insulated and pvc sheathed, frls, armoured heavy duty underground cable, isi marked with aluminium stranded conductor 1100 volt grade of size 3.5 core, 25 sq.mm cross section suitable for earthed system, laying in trenches / duct / fixed to poles / drawn through pipes / sleeving through pipe in duct, including suitable size double compression copper stainless steel cable gland, crimping type cable lugs, sockets etc. complete all as specified and as directed. 125 m & l for dry river sand cushioning over and around the cable for cable protection in trenches, levelled and punned down complete all as specified and as directed. note: the punned down thickness shall be measured for payment. 126 supply and lay bricks, common burnt clay building bricks, sub–class b, designation 75 in trenches for cable protection complete all as specified and as directed. 127 supplying and laying gi pipe, 40mm dia, light grade for cable protection at road crossing etc. or fixing on wall / poles of any type, secured with clamps complete all as specified and as directed. 128 m & l for cutting bituminous road / hardstanding etc. as required for jointing / laying cables and pipeline of width not exceeding 300mm and depth not exceeding 600mm and refilling after laying and making good with pcc 1:2:4, type b1 using 20mm graded stone aggregate, 100mm thick complete all as specified and as directed. 129 earthing complete with galvanised steel earth plate electrode 600 x 600 x 6 mm thick burried directly in ground [ earth pit not less than 2.25 m deep below ground level ] with top edge of plate not less than 1.50 m below normal ground level connected to 4 mm gi wire [ earth lead ] and gi pipe 15 mm, medium grade for earthing lead protection to the extent of maximum 7.5m, earth plate electrode surrounded by 150mm thick packed layers of charcoal and common salt filled in alternate layers, connected to the plate by means of gi bolts & nuts complete all as per electrical plate no. 3 of ssr part – i, connected to panel / db including testing on completion including main earthing, charcoal, common salt, pcc [ 1:2:4, type b1 ] pit with rcc 1:2:4, type b1 cover, 50 mm thick with 6 nos, 8 mm dia tmt bars in both ways, ms frame made with 40 x 40 x 6 mm angle iron, ms funnel with 20 mm bore, medium grade gi watering pipe, wire mesh, earth work excavation, return filling, removal of surplus soil etc.complete all as specified and as directed. 130 s & f microprocessor based single phase, 2 wire smart prepaid electronic tamper proof digital energy meter with bright lcd display, in home display unit including implementation of vending software system through server duly mapping of consumer, token system, load control facility, optical port for local communication / consumer interface unit with in built blue tooth low energy [ ble ] for remote access and alongwith vending software, high accuracy, rating 5 to 60 ampswith class 1 accuracy, ip 54 ingress protection, conforming to is 16444 & is 15959, iec 62055 31, iec 62053 21, iec 62052 11, cbip publication no. 304, isi marked, suitable for 240 volts, ac, 50 hz, including housing inmeter box with provision for earth connection, two separate cable entries for incoming and outgoing cables, transparent glass door for reading visibility with hinges and provision of 4 nos. of tamper proof lead free seals, complete all as specified and as directed. make: siemens / l & t / havells / hpl / schneider / securenote: [ a ] energy meter shall be provided with 10 years onsite replacement warranty and the rate quoted is deemed to be including the same and nothing shall be paid extra on this account. [ b ] the bidder is required to submit authenticity certificate issued by oem for the meters supplied under this contract. [ c ] meter box shall be measured for and paid separately under relevant item of boq. 131 s & f hot press moulded smc meter box of size not less than 250mm ( h ) x 250mm ( w ) x 155mm ( d ) suitable for housing of single phase prepaid electric energy meter, conforming to relevant is, with viewing glass, hinged door and earth bolt, mounted on pole / wall with suitable clamps / bolts / nuts complete all as specified and as directed.make: cat no. gsmb 2525 of sintex or equivalent in hensel / c&s 132 s & f upvc pipe of 50 mm bore, of pressure rating 10 kgf / sq.cm including all fittings such as bends, tees, short pieces, connectors, elbows, reducers, sockets etc and fixed to walls, ceiling, and laid on floors including testing complete all as specified and as directed. 133 s & f upvc pipe of 25 mm bore, of pressure rating 10 kgf / sq.cm including all fittings such as bends, tees, short pieces, connectors, elbows, reducers, sockets etc and fixed to walls, ceiling, and laid on floors including testing complete all as specified and as directed. 134 s & f gun metal globe or gate valve of class i, pressure tested of 1.5 mpa, 50 mm bore with iron wheel head, screwed both ends for iron pipe, conforming to is, isi marked complete all specified and as directed. 135 m & l for cutting or screwing existing steel tubing for alteration or additions of suitable size for 50mm dia complete all specified and as directed. 136 m & l for construction of valve chamber of size 600 x 600 x 600 mm internal size suitable for sluice valve, with pcc 1:4:8, type d2, using 40mm graded aggregate for foundation, 200 mm thick brickwork with fly ash bricks in cement mortar 1:6, 40 mm thick pcc, 1:2:4, type b1, using 20mm graded aggregate coping, rendering in cm 1:4, 15 mm thick including provision of mild steel sheet cover 3 mm thick with 40 x 40 x 6 mm size angle iron frame work embedded in concrete with suitable hinges and locking arrangements including two coat of synthetic enamel black paint over a coat of red oxide zinc chrome primer to steel surfaces and includingdemolition of existing valve chamber, necessary earth work excavation in any type of soil etc., removal of surplus soil off the premises complete all as specified and shown on drawing cedd / td / 119, sheet no. 1 / 1 dated 20 august 1983, revised up to 21 september 1992....
33448059 bids are invited for wrought aluminium and aluminium alloys extruded tube and hollow sections for general engineering purposes (q3)mse total quantity : 498...
33335749 tender for supply of technology and design, engineering, manufacturing and supply, erection and commissioning of required equipment for setting up high and aluminum alloy melting plant and casting production plant...
33296430 supply of manganese activated low potential aluminum alloy sacrificial anodes ( pkoa ) ...
33176703 supply of supply of 19/3.99mm aac spider conductor (aluminum alloy stranded conductor) as per is:398 (part 1) 1996 or latest.supply of 19/3.99mm aac spider conductor (aluminum alloy stranded conductor) as per is:398 (part 1) 1996 or latest.,supply of 19/3.99mm aac spider conductor (aluminum alloy stranded conductor) as per is:398 (part 1) 1996 or latest. sse/ohe & andhra pradesh 500.00 metre...
33157743 bids are invited for wrought aluminium and aluminium alloys extruded tube and hollow sections for general engineering purposes (q3) total quantity : 375...
33084146 extension supply of technology and design engineering manufacturing and supply erection and commissioning of required equipment for setting up high end aluminum alloy melting plant and casting production plant...
32965241 replacement of defective light, repair and maint of lt panel board metering equipment, switch gears, day to day maint of 11 kv distribution cables, attending complaint and replacement of unsv ug cable gallery earthing, earthing strips all allied work replacement of defective light, repair and maint of lt panel board metering equipment, switch gears, day to day maint of 11 kv distribution cables, attending complaint and replacement of unsv ug cable gallery earthing, earthing strips all allied work servicing / maintinance ofmultiple section oflt panel board in one substation comprising minimum up to 05 nos acbs / mccbs / sdfs , busbar chamber, swich gear chamber, metering chamber cable termination / tray chamber after opening front / top / side / back cover by using forced air pressure andbrushes, cleaning of all dust / durt, complete cleaning of out side surface of panel board using suitable cleaning agents, tighting of all nuts & bolts of busbar / switchgear / cable terminals, repair / replacement to defective metering wiring from acb / mccb / ct to meter and replacement of defective meters, cts, indicator lamp, metering terminal blocks, mcb, replacement of defective aluminum cable lugs, nuts bolts washers, replacement of defective panel knob / door knob and hinges complete all as specified and as directednote: ( i ) panel meter, indicator lamp, mcb, busbarand ct will be measured and paid seperately as supply only. ( ii ) required aluminium cable lugs, metering cables and nuts bolts washers shall be inclusive of quoted rate. ( iii ) servicing / maintinance of acbs measured seperatelly. 2 all as per item no 1.00 above but comprisingacbs / mccbs / sdfs up to total 10 nos 3 all as per item no 1.00 above but comprisingacbs / mccbs / sdfs up to total 15 nos 4 all as per item no 1.00 above but comprisingacbs / mccbs / sdfs up to total 23 nos 5 all as per item no 1.00 above but comprisingacbs / mccbs / sdfs up to total 28 nos 6 servicing, repair, maintinance of air circuit breaker 630 amps to 3200 amps capacity by drawing out movable unit, forced air cleaning of movable and fixed unit, decarbonize breaker contracts and checking for any defects due to any flush / loose contact, cleaning of all fixed and moving contact point, terminal connection points with ctc, replacement of defective parts and re fixing acb, cables completes all as specified and as directed. note: ( a ) required male / female acb contacts, trip coils, closing coils, electronic protection unitwill be measured as supply only. ( b ) all cleaning agents are included in the quoted rate. 7 supply only fixed contract of acb 630a to 3200acomplete all as specified and as directed 8 supply only moving contract of acb 630a to 3200acomplete all as specified and as directed 9 supply only electronic protection unit of acb 630a to 3200acomplete all as specified and as directed 10 supply only shunt trip coil of acb 630a to 3200acomplete all as specified and as directed 11 supply only closing coil acb 630a to 3200a complete all as specified and as directed 12 supply only digital electronic ammeter ( 0 3200 amps range ) withbuilt in selector switch suitable for lt 415 v panel flush pattern square type 96 mm x 96 mm with adopter completeall as specified and directed. cat part no: 30002385 ( dm3110 ) make: schneider or conserve / l&t / hpl 13 supply only digital electronic volt meter ( 0 500 volts range ) withbuilt in selector switch suitable for lt 415 v panel flush pattern square type 96 mm x 96 mm with adopter completeall as specified and directed. cat part no: 30002386 ( dm3210 ) make: schneider or conserve / l&t / hpl 14 supply only indication lamps ( led type ) red, yellow and blue in colours of 22.5 mm dia to monitor on lt panel board suitable for 240 v ac supply and taking down unserviceable indication lamps complete all as specified and directed. cat part no: 1sfa619402r5201 make: siemens / c&s / schneider / abb 15 supply only metering current transformer of 1000 / 5 amps class 1, 15 va, completeall as specified and directed by engr in charge.make: rishabh or equivelent of kappa / ae 16 supply only metering current transformer of 1200 / 5 amps class 1, 15 va, all complete all as specified and directed.make: rishabh or equivelent of kappa / ae 17 supply only metering current transformer of 1600 / 5 amps class 1, 12.5 va, complete allas specified and directed.make: rishabh or equivelent of kappa / ae 18 supply only metering current transformer of 2000 / 5 amps, class 1, 12.5va, complete all as specified and directed. make: rishabh or equivelent of kappa / ae 19 supply only metering current transformer of 2500 / 5 amps, class 1, 5va, complete all as specified and directed. make: rishabh or equivelent of kappa / ae 20 supply only metering current transformer of 3000 / 5 amps, class 1, 1.5va, complete all as specified and directed. make: rishabh or equivelent of kappa / ae 21 supply only metering current transformer of 800 / 5 amps, class 1, 2.5va, complete all as specified and directed. make: rishabh or equivelent of kappa / ae 22 supply only switch disconnector fuse unit , tpn , open execution, bolted fuse link, 415v, conforming to is / iec 60947 3, telescopic shaft for depth adjustment terminal shrouds on both side, door interlock facility of current rating 250 amps including boted hrc fuse 03 nos ( make l&t, cat no fn 250 tpn sk 95682 & hrc fuse st 30781 or equivelent of siemens / abb / havells ) 23 all as per item no 22.00 above but capacity of 400 amps. ( make l&t, cat no fn 315 tpn sk 95591 & hrc fuse st 30784 or equivelent of siemens / abb / havells ) 24 supply only hrc fuse of capacity 400 ampscomplete all as specified and as directed ( make l&t cat no sf94335 and equivalent to standard / ge / schneider ) 25 supply only hrc fuse of capacity 250 ampscomplete all as specified and as directed ( make l&t cat no sf94333 and equivalent to standard / ge / schneider ) 26 supply and fix mccb, 4 pole, 400 amp, 36 ka braking capacity, ics = 100% icu as per iec 60947 2, with micrologic 2 ( up asic based ) , complete all as specified and as directedmake schneider cat part no lv432677 or equivelent of legrand / abb 27 all as item no 26.00 above but of size 4 pole, 630 amp, 36 ka. make make schneider cat part no lv432877 or equivelent of legrand / abb 28 all as item no 26.00 above but of size 4 pole, 250 amp, 36 ka. make make schneider cat part no lv431780 or equivelent of legrand / abb 29 all as item no 26.00 above but of size 3 pole, 160 amps, 36 ka. make schneider cat part no lv430770 or equivelent of legrand / abb 30 supply and fix mccb 3 pole, 125 amps, 25 ka braking capacity, ics = 100% icu as per iec 60947 2, with thermal magnetic trip unit. complete all as specified and as directed make schneider cat part no lv430311 or equivelent of legrand / abb 31 supplay, fix and connecting by mannualchangover switchsheet steel enclosure versionconforms to iec 60947 3 of capacity 630 amps four pole complete all as specified and as directed ( make l&t cat part no co46300osooor equicalent to havells / indo asian. 32 supplay, fix and connecting by mannualchangover switchsheet steel enclosure versionconforms to iec 60947 3 of capacity 400 amps four pole complete all as specified and as directed ( make l&t cat part no co44000osooor equicalent to havells / indo asian. 33 supplying and laying synthetic rubber insulated mats 2 mm thick for voltage upto 3.3 kv for electrical purpose as per is 15652 2006, ( superseding is 5424 ) suitable for electrical shock safety of sizes 2m x 1m.complete all as specified and as directed 34 m&l for painting of outer surface of multiple section ofcomplete lt panel board size up to 5.5 m x 3.2 in one substation comprising acbs / mccbs / sdfs , busbar chamber, swich gear chamber, metering chamber cable termination / tray using one coat of synthetic enamel paint after preparation of surface, providing protection cover to all metering equipment, panel meters, switchgears, cleaning of all meters and switch gearscomplete all as specified and as directed 35 all as per item no 34.00 above but lt panel board size up to 7.5 m x 4.5 m. 36 m&l for painting of both side surface of ms cable trench cover using one coat of black bituminius paint after preparation of surfacecomplete all as specified and as directed 37 m&l for plate girder or single stanchions, fe 290 built up of one beam or channel section with flange plates, caps bases, splices, angle brackets, cleats and other connection and taking out of oldunsv ms cable cover / support structure. 38 dimantling, taking out all earth connection of strip from panel board to earth test pit any size and replace the worn out earth strip, nut / bolts / washers connect all joint with new nots, bolts and washers to in original positioncomplete all as specified and as directednote : earth gi strip measured and paid separetely 39 m & l for earth continuity conductor gi strip of size 32 x 6 mmcomplete all as specified and as directed 40 m&l for writing letter and fixing lt panel boardsurface showing incoming and outgoing capacity inamps and feeder name of letter five not less than 30 x 50 mm complete all as specified and as directed 41 dismantlingexisting unserviceable / corrodedlt pillar box and supply, fabricate, install, testing and commissioning out door type, double door dust & vermin proof lt pillar box of 2.1 m length, 1 m width & 1.6 m height fabricated vertically by using 50x50x5 mm angle iron frame, fixing with nuts & bolts on 75 x 40 mm ismc as per directions of engineer in charge and using 3 mm thick crca ms sheet all over body front and back cover with hinges and aldrops for locking arrangments, 1 mm thick frp coating all over the external surfaces and 3 mm thick ms sheet for bus bar cover, piller box, partitions and bottom cable entry covers duly painted with one coat of redoxide and two coats of synthetic enamel paint including control wiring complete in lt piller box with 1.5 sq mm frls copper conductor cable and 5a mcb sps 2.5 amp for meters, breaker control supply and indication lamps and provision to accommodate the following: ( a ) 3 ph+1n copper busbar of equal sizes of capacity 1.5 times of ratedcurrent of incoming switchgear. ( b ) 3 ph+1n copper busbar of equal sizes of capacity 1.5 times of ratedcurrent of outgoing switchgears as down links / connectivity links to switchgear. 42 ( c ) digital ammeter & voltmeter for incoming & digital ammeter for outgoing. ( d ) led indication lamps for ryb for incoming and outgoing indication. ( red, yellow & blue coloured ) ( e ) lt acb – 1600amps, 4p, 50ka, complete with over current and earth fault tripping device as incomer 01no ( f ) lt acb 1600 amps, 3p, 50 ka complete with over current and earth fault tripping device as out going 01 no ( g ) mccb 630amps, 3p, 36ka complete with over current and earth fault tripping device as out going 01no ( h ) mccb 400amps, 3p, 36ka complete with over current and earth fault tripping device as outgoing 01nonote : ( i ) unit rate quoted include for necessary grouting / chipping of concrete and anchor fastners and providing necessary pcc ( 1:2:4 ) type b1 using 20 mm gradedcrushed stone agreegate for foundation to fix the lt piller box. ( ii ) cost of digital ammeter, voltmeter, led lamps, cts, lt acbs, mccbs and mcbs shall be included in the quoted rate. ( iii ) drawing shall be got approved by ge before fabrication of the lt piller box. ( iv ) all incoming and outgoing cable connections are to be made as per existing one and rate deemeded to be included in the quoted rate. ( v ) the pillar box shall be brought to jetty gallery part by part and to be assembled in site being limited space of work / movement and rate shall deemed to be included in quoted rate. ( vi ) copper busbars with pvc sleeves shall be measured and paid seperately under respective item in this schedule as supply only 43 supply only copper bus bar links with pvc sleeves of raing 630 a to 2000 acomplete all as specified and as directed 44 supply and fix lt acb 4 pole4000 a, 50 ka breaking capacity, 415 v, 50 hz, manual drawn out type and manually charged with micro processor et2l trip unit ( without display ) release protection system against over current, earth fault and short circuit with 2 no + 2 nc auxiliary switch, safety shutter, cradle guard, operating handles conforming to iec 60947 2 & 3complete all as specified and as directedmake: cat.no. mvs40n4mw2lofschneider / l&t / abb / ge / legrand 45 all as per item no 44.00 above but of capacity2000amps, 4polecat.no. mvs20n3mw2lof schnider equivelent make inl&t / abb / ge / legrand 46 all as per item no 44.00 above but of capacity1600amps, 4polecat.no. mvs16n3mw2l of schnider equivelent make inl&t / abb / ge / legrand 47 all as per item no 44.00 above but of capacity1250amps, 4polecat.no. mvs12n3mw2l of schnider equivelent make inl&t / abb / ge / legrand 48 all as per item no 44.00 above but of capacity1000amps, 4polecat.no. mvs10n3mw2lof schnider equivelent make inl&t / abb / ge / legrand 49 attending day to day electrical complaints and call on repair of control panel of street light, security light, garden light, perimeter light, tower light & high mast light providedinsidedockyard, decarbonizing all contact points of contactors , replacement of wornout aluminium cable lugs, wornout screws, nuts, bolts and washers, tightening the loose connections whereever required, adjustment of timer, cleaningand restore the power supply complete all as specified and as directednote : ( i ) replacement of spares vizmcb, mccb, contactors, timers, cables, will be measured and paid for separately as supply only and labour element for taking down the replaced spares shall be deemed to include in the unit rate quoted. ( ii ) if the qty of complaints to be attended in a control panel / lt panel is more than 01 no in a day, altogether the complaints will be considered only 1 ( one ) . ( iii ) the contractor has to engage qualified electricians and helpers in sufficient nos to attend and rectify the defects. ( iv ) job card for repairing work will be issued by concern je and the same shall be signed by contractor / or his rep and shall be returned to concerned je on completion of each job work. 50 material and labour for disconnecting the burnt out high mast tower winch motor 3 phase , 415v, 50hz, 1400 rpm, 4 pole, 2hp and rewinding with supper enameled copper wire of same gauge / size of wire including re fixing the same in its original position testing and commissioning complete all as specified and as directed 51 material and labour for servicing of high mast tower control mechanism by greasing and varnishing of electric motor 2 hp, 3 phase 415 volts 50hz including replacement of unsv plug and socket for trouble free functioning including painting of starter panel with one coat of synthetic enamel paint complete all as specified and as directed 52 supply and fixing high mast tower winch motor 3 phase 415 v 50hz 1400 rpm 4 pole 2hp complete all as specified and as directed 53 s&f pvc junction box of outdoor type, weather proof, with provision of hole at bottom for cable entry, hinged door with locking arrangement, of size not less than 200mm ( l ) x 100mm ( b ) x 300mm ( h ) incl taking down unserviceable one, fixed to pole with ms clamp, nuts, bolts and washers complete including one 3ph 4 pole connection block. complete all as specified and as directedmake syntex / hansel 54 supply and fixing / laying through trench.surface or wall including required necessary saddle / clamp any highthdpe double wall pipe corugated pipe of size 40 mm dia for cable protection laid in trenches in lieu of sand / brick protection complete all as specified and as directed 55 taking out old unserviceable lt ug cable of any size any description including hdpe pipe and bricks for cable protection where ever appeared and complete all as specified and as directed 56 supply and laying in trenches xlpe insulated, armoured, heavy duty electric cable with stranded aluminium conductor, 1100 volts grade cross section area 6 sqmm 2 core and connection complete with aluminium cable lugscomplete all as specified and as directed 57 all as per ser no 56.00 but of size 10 sqmm, 4 core 58 all as per ser no 56.00 but of size 16 sqmm 4 core 59 all as per ser no 56.00 but of size 25 sqmm 3.5 core 60 all as per ser no 56.00 but of size 35 sqmm 3.5 core 61 m&l for dismatling and taking out street light cable loop near pole forsize of cable 6sqmm to 25 sqmm after dismantling connection from junction box, cutting, removing damaged portion of the cable ends, providing new aluminium cable end terminals, laying of cable through protection pipe through coping to junction box including necessary connection complete all as specified and as directed. ( note: earth work, pole coping pcc, cable protection, pipe measured separately ) 62 m&l for dismantling taking out cables 10 sqmm to 16 sqmm from trench, including making straight through joints at damaged portion and relaying to trench complete all as specified and as directed ( note: earth work, hdpe pipe for cable protection will be measured and paid separately. heat shrink straight through cable joints inclusive of quoted rate ) 63 m&l for dismantling taking out cables 25 sqmm to 35 sqmm from trench, making straight through joints at damaged portion and relaying to trench complete all as specified and as directed ( note: earth work, hdpe pipe for cable protection will be measured and paid separately. heat shrink straight through cable joints inclusive of quoted rate ) 64 supply and fixing pvc insulated, pvc round shethed copper flexible electric cable 1.5 sqmm 3 core, 1100 volts grade and dismantling wornout / defective cables from sl / flood light fitting at pole / tower top to jb at bottom of pole through pole / tower complete all as specified and as directedmake : plaza / gloster / havells / polycab. 65 m&l for complete servicing, repair, maintenance of timer panel, by cleaning inside and outside, replacement of burnt mcb, mccb, timer, contactor, wiring, bypass toggle switch complete all as specified and as directednote: replacement of mcb, mccb, timer, contactor shall be measured as supply only 66 supply only power contactor 3 phase, 415v, 32 amps cap utilsed for heavy duty by taking down the old perished / deteriorated contactor complete all as specified and as directedmake: schneider, model etvs lc1e3201 or equivelent of legrand / l&t / abb 67 supply only surface mounting analog time switchesheavy duty of 230 v 50hz including dismantling taking down unsv one and complete all as specified and as directedmake : 6499 15 maxi rex 4qt ( daily ) of legrand or equivelent of abb / l&t 68 supply only mcb, sp, 10ka, c 6 32 a including dismantling taking down unsv onecomplete all as specified and as directedmake: schneider or equivelent of legrand / abb / l&t 69 supply only mcb, dp, 10ka, c 40a 63 a including dismantling taking down unsv one complete all as specified and as directed make: schneider or equivelent of legrand / abb / l&t 70 supply only mcb, 4p, 10ka, c 40a 63 a including dismantling taking down unsv onecomplete all as specified and as directedmake: schneider or equivelent of legrand / abb / l&t 71 supply only mccb with thermal magnetic release, 16 ka, 3 pole, 415v, 100 a, complete all as specified and as directedmake: schneider , model easy compact cvs 100 bs, lv510950 to 58 or equivelent of legrand / abb / l&t 72 m&l for dismantling of non functional street light / flood lightfrom any type of pole at hight upto 9 mtr by suitable ladder for repair of the same for replacement unserviceable items like led driver, connector block and decarbonising contact points and refixing the same to pole after repair of any type securitylight .note: required led driver shall be measured and paid separately 73 supply only led driver suitable for street light fitting 1x 120 watt, 230v, make cg / halvells / bajaj / philips / wipro 74 supply only led driver suitable for street light fitting 1x 150 w , 230v, make cg / halvells / bajaj / philips / wipro 75 supply only led driver suitable for flood light fitting 1x 200 w, 230v, make cg / halvells / bajaj / philips / wipro 76 supply only led driver suitable for flood light fitting 1x 250 w, 230v, make cg / halvells / bajaj / philips / wipro 77 s&f on wall / pole timer enclosure out door type complete with timeranalog time switchesheavy duty of 230 v 50hz, power contactor 3 phase mnx 18 , 415v, 32 amps, mcb, tpn, 10ka, c 40a 63 a with, rotary switch with connector for incoming and outgoing cable entry complete all as specified and as directedmake indi asian / havells 78 m&l for painting of steel fabricated light tower not less than 10 mtr high with one coat of aluminium paint after preparation of complete surface complete surface including writing tower number with synthetic enamel black paint complete all as specified and as directed 79 m&l for painting of steel tubular pole any type / swan neck pole with one coat of aluminium paint after preparation of complete surface including writing pole number with synthetic enamel black paint complete all as specified and as directed 80 m&l for white wash to pole coping pcc complete all as specified and as directed 81 s & f street light fitting led 150 watt watt incl dismantling taking down unsv one complete all as specified and as directed.make cg or equivelent of halvells / bajaj / philips / wipro 82 s & f flood light fitting led 210 watt watt incl dismantling taking down unsv one complete all as specified and as directedmake cg or equivelent of halvells / bajaj / philips / wipro 83 s & f flood light fitting led 300 watt incl dismantling taking down unsv one complete all as specified and directed, make cg, model cfs 501 300 57 60d sl gl ngg or equivelent of halvells / bajaj / philips / wipro 84 s & f flood light fitting led 350 watt incl dismantling taking down unsv one complete all as specified and directed, make cg, model cfs 501 350 57 60d sl gl ngg or equivelent of halvells / bajaj / philips / wipro 85 taking down old unserviceable aviation light fitting, and supply & fix new led aviation light fitting withyellow painted die cast aluminium alloy housing, red coloured polycarbonate dome and accessories includingclamps, nuts, bolts and service connections up to the junction box complete all as per make bajaj andcat no.bjaol 2 bc gls 2 x 100w bc bajaj or eqiuvalent in philips / cg / havells / wipro. 86 excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m in depth and getting out in soft loose soil for cable work or from above cable duct complete all as specified and as directed 87 returning, filling in including spreading, levelling, watering and well ramming in layers not exceeding 25cm thick complete all as specified and as directed. 88 removing of excavated material not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and as directed. 89 m&l for dry sand cushioning for under groundcable provided with layer and sand 8 cm deep before laying the cable and 15cm after laying the cable complete all as specified and as directed. 90 supplying and laying un reinforced precast concrete cable cover, class hv, type 1, flat, size 300mm x 180mm x 40mm complete all as specified and as directed 91 surface dressing of areas of above cable duct by clearing away all grass, wild vegetation, saplings, shrubs, brushwood, undergrowth, roots, and trees not exceeding 30cm girth and removing rubbish upto a distance of 50 meters outside the periphery of the area under clearance complete all as specified and as directed 92 m & l making chequrered plates as per existing sizes and thickness both side lifting handle as per existing one including painting of one coat red oxide primerand two coat of black bituminius paint, including necessary pcc wks as per site requirment and taking out of old unsv chequered plate complete all as specified and directed. 93 cleaning of cable duct of size 1.2 x 1.0 by removing out all mud, soil, waste materials and disposal of waste materials to nearest gurbage bin and soil mud to low laying area of dockyard 94 s / f of cable rack made with structural steel section of isa 75x75x8mm, ( fe 290, gde e 165 ) pre welded, inside duct, on wall , placing in position and fixing to wall with fastener steel bolt not less than20 mm dia, including painting with one coat of red oxide and two coat of black bituminous paint all as specified and directed. note: cable rack drawing shall be obtained from engr in charge. 95 dismantling taking out unserviceable ms cable support from wall / surface of gallery any type by removing nuts & bolts / cutting braces complete all as specified and as directed 96 taking out old unsv ht ug cable of any size and any description including gi pipe of any dia and bricks for cable protection where ever appeared and complete all as specified and as directednote: ( 1 ) excavation and earth work shall bemeasured and paid separately. ( 2 ) serviceable cable obtained shall be stacked properly for re use. 97 m & l xlpe insulated, screened, pvc bedded, galvanised steel strip or wire armoured, electric power cables ( heavyduty ) with aluminium conductor, 11000 volts earthed, grade cross sectional area 185 sq. mm 3 core complete all as specified and as directed 98 all as per item no 97.00 above but for cable sizes 240 sqmm 3 core 99 all as per item no 97.00 above but for cable sizes 300sqmm 3 core 100 all as per item no 97.00 above but for cable sizes 400sqmm, 3 core 101 supply only cable jointing kit for 11 kv ( earthed ) grade cable for indoor termination heat shrink type joint complete with jointing material and accessories suitable for 3 core xlpe armoured aluminium conductor cable of size 185 sqmm incl dismentling / taking down unserviceable one complete all as specified and as directed 102 all as per item no 101.00 above ( indoor termination ) but for cable of size 240sqmm to 300 sqmm incl dismentling / taking down unserviceable one complete all as specified and as directed. 103 all as per item no 101.00 above ( indoor termination ) but for cable of size 400 sqmm incl dismentling / taking down unserviceable one complete all as specified and as directed. 104 supply only cable joining kit for 11 kv ( earthed ) grade cable for straight through heat shrink type joint complete with joining material and accessories suitable for 3 core xlpe armoured aluminium conductor cable of size 185sqmm incl dismentling / taking down unserviceable one. 105 all as per item no 104.00 above ( straight through heat shrink type joint ) but for cable of size 240sqmm to 400 sqmm incl dismentling / taking down unserviceable one complete all as specified and as directed. 106 m & l for road cutting / hard standing to a depth not less than 80 cm and not less than 60 cm wide for laying of gi pipe to draw to ugcable and making good the disturbed surface by filling of pcc ( 1:3:6 ) type c 2 using 40 mm graded stone aggregate and finished the surface even and smooth with out using extra cement and disposal off the surplus debris and soil to a distance not exceeding 50 m complete all as specified and as directed by engr in charge. 107 m & l 80 mm bore gi pipe tubes light grade for cable protection supporting with all fixing accessories ( clamp, nuts, bolt and washer etc ) complete all as specified and as directed by engr in charge. 108 dismantling taking out ht cable from cable rack / floor at gallery of marine jetty for repair / replacement of wornout steel cable rack or for realingnment of cable and refixingthe cables with proper staking with proper alignment of cable on repaired / existing rack and making feeder wise bundle of cable using pvc cable tie for sizes of cable 3 core, 185 to 240 sqmm, 11000 volts grade complete all as specified and as directed. note: each cable shall be measured separately.steel cable rack shall be measured separately as supply and fix 109 all as per item no 108.00 above but for cable sizes 300 to 400 sqmm, 3 core. 110 m&l for finding of cable fault of ug 11000 volts grade cable inside trench ( under soil / drain / pcc / road / trench ) by disconnecting both cable ends, using insulation tester, cable path / fault finder and rectification complete by necessary excuvation, cutting at fault position, fixing of straight through heat shrink joint, for cable sizes 185 sqmm to 400 sqmm, 3 core, 11000 volts grade or replacement of heat shrink indoor cable joint kit of size 185 sqmm to 400 sqmm, 3 coreand reconnection of both cable end to original position after complete satisfactory insulation test, fixing with old or required new nuts bolts washers complete with testing complete all as specified and as directednote: ( a ) items required for rectification such as heat shrink indoor cable joint kit / heat shrink straight through joints / heat shrink sleeves and earth work shall be measured separately . ( b ) required aluminium cable lugs and nuts bolts washers shall be inclusive of quoted rate. ( c ) contractor shall bring necessary testing equipment and rate shall be inclusive of quoted rate. 111 m&l for earthing complete with glvn. gi plate earth electrode 60cmx60cmx6 mm thick burried in ground vertically to a depth n. less than 1.5 m below normal gl, connected to gi strip32x6 mm earth lead by means of nuts, bolts, check nuts & washers all as specified and indicated inclu. concrete pit in pcc 1:3:6 type c 2 rcc, precast pit cover slab 400mmx400mmx80mm with handle for lifting made out of 8mm dia ms rod fixed flush to pit, funnel, wiremesh, 20mm dia gi pipe medium grade for watering charcoal and salt in alternate layers including necessary earth work excuvation & removal etc complete all as specified in plate no 5 of ssr part i 1991 ( zone e ) 112 m & l for earth continuity conductor gi strip of size 32 x 6 mm . 113 painting chequrered plates as per existing sizes and thicknessof one coat red oxide primerand two coat of black bituminius paint, complete all as specified and as directed 114 supply and fix cable route indicator to indicate path of ht cable 11000 volte material usde cast iron with pcc work complete all as specified and as directed...
32913265 supply of aluminium alloy anodes , aluminum alloy anodes as per drawing attached alap k t type 189a025 and size: ( 120+160 ) x 155 mm x 250 mm . net weight of each anode 14.3 kg. with mtc , aluminum alloy anodes as per drawing attached alap k. t type 5 268 a025s and size: ( 190=230 ) x210x280. net weight of each anodes 29.1 kg .with mtc. , aluminum alloy anodes as per drawing attached.alap k t type t 56a100. size: ( 33 +47 ) x47x1000 net weight of each anodes:4.71 kg. with mtc , aluminum alloy anodes as per sample . net weight f each anodes:14.3 kg.with mtc....
32900279 tender for selection of market research firm to perform the demand supply analysis of aluminium alloy flat rolled products (frp) market and recommend product mix & go to market strategy for a new plant of 60,000 tpa capacity at nellore, andhra pradesh, india...
32742912 extension supply of technology and design engineering manufacture and supply erection and commissioning of required equipment for setting up high end aluminum alloy melting and casting production plant...
32737762 aluminium alooy anodes aluminium alooy anodes , aluminum alloy anodes as per drawing attached alap k t type 189a025 and size:(120+160) x 155 mm x 250 mm . net weight of each anode 14.3 kg. with mtc , aluminum alloy anodes as per drawing attached alap k. t type 5 268 a025s and size: (190=230)x210x280. net weight of each anodes 29.1 kg .with mtc. , aluminum alloy anodes as per drawing attached.alap k t type t 56a100. size:(33 +47)x47x1000 net weight of each anodes:4.71 kg. with mtc , aluminum alloy anodes as per sample . net weight f each anodes:14.3 kg.with mtc....
32680782 auction sale of lot no: 18 lot name: alluminium alloy...
32547293 tender for installation of high end aluminium alloy melting, casting and flat rolled products production facility at nellore, andhra pradesh...
32547240 installation of high end aluminium alloy melting casting and flat rolled products productions facility...
32405521 auction sale of lot no: 2 lot name: alum. scrap alluminium alloy...
32276362 supply of gravity cock 1/2 inch (aluminium alloy) similar to jayson, powder coating conforming to icf/md/spec.091 rev.01 to icf drg.no.icf/sk 6 3 369, item 1, alt. g/2gravity cock 1/2 inch (aluminium alloy) similar to jayson, powder coating conforming to icf/md/spec.091 rev.01 to icf drg.no.icf/sk 6 3 369, item 1, alt. g/2,gravity cock 1/2 inch (aluminium alloy) similar to jayson, powder coating conforming to icf/md/spec.091 rev.01 to icf drg.no.icf/sk 6 3 369, item 1, alt g/2 carr. repair andhra pradesh 7714.00 numbers stores/tpty , scr...
32013338 supply of supply of of non ferrous fasteners consists of 10 items (enclosed as annexure 1 also), as per rdso specification no.ti/spc/ohe / fasteners /0120 rev 1 (march 2017 or latest). 1. copper split pin of size 5x40mm 1 no. 2. copper split pin of size 4x40mm 15 no. 3. copper split pin of size 4x32mm 5 no. 4. copper split pin of size 2.5x25mm 4 no. 5. copper split pin of size 2.5x20mm 2 no. 6. aluminum alloy rivets of size 6x 35 mm 8 no. 7. copper rivets of size 6x60 mm 4 no. 8. coppersupply of of non ferrous fasteners consists of 10 items (enclosed as annexure 1 also), as per rdso specification no.ti/spc/ohe / fasteners /0120 rev 1 (march 2017 or latest). 1. copper split pin of size 5x40mm 1 no. 2. copper split pin of size 4x40mm 15 no. 3. copper split pin of size 4x32mm 5 no. 4. copper split pin of size 2.5x25mm 4 no. 5. copper split pin of size 2.5x20mm 2 no. 6. aluminum alloy rivets of size 6x 35 mm 8 no. 7. copper rivets of size 6x60 mm 4 no. 8. copper,supply of set of non ferrous fasteners consists of 10 items (enclosed as annexure 1 also), as per rdso specification no.ti/spc/ohe / fasteners /0120 rev 1 (march 2017 or latest). 1. copper split pin of size 5x40mm 1 no. 2. copper split pin of size 4x40mm 15 no. 3. copper split pin of size 4x32mm 5 no. 4. copper split pin of size 2.5x25mm 4 no. 5. copper split pin of size 2.5x20mm 2 no. 6. aluminum alloy rivets of size 6x 35 mm 8 no. 7. copper rivets of size 6x60 mm 4 no. 8. copper rivets of size 6x50 mm 4 no. 9. phosphor bronze spring washer of size m 10 6 no. 10.phosphor bronze spring washer of size m 12 13 no....
31822264 identification of oems / authorized service personnel / service contractor for amcu in prakasam. supply of 40 liters capacity aluminum alloy milk cans to the districts....
31741484 bids are invited for 3mm thick h11x aluminium alloy sheet...
31686118 bids are invited for 7% tin lead sheet 3.00 mm thick n9535 015949 (q3) , alu. bronze bar rd solution heat dia 50mm n9530 000144 (q3) , alu. bronze bar rd solution heat dia 40mm n9530 000143 (q3) , bar rd alluminium bronze 25mm dia n9530 000141 (q3) , alu bronze bar rdsolution heat dia 100mm n9530 000147 (q3) , mildsteel sheet black 2500x 1250x160mm n9515 000180(q3) , sheet alluminium alloy sheet 2400x900x3.55mm n9535 000443 (q3)mse total quantity : 233...